Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT
NM1440E _51 Engine / Hybrid System _056079 1GR-FE ENGINE MECHANICAL _0273697 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Cylinder Head Cover Sub-assembly

i.

Lightweight yet high-strength aluminum cylinder head cover sub-assemblies are used.


ii.

An oil delivery pipe is installed inside each cylinder head cover sub-assembly. This ensures lubrication to the sliding parts of the roller No. 1 valve rocker arm sub-assemblies, improving reliability.

W102077E03
3.125,0.573 2.781,0.229 2.781,0.229 1.927,0.229 true 3.854,0.531 4.167,0.229 4.167,0.229 5.083,0.229 true 4.719,1.875 5.271,1.323 5.271,1.323 5.833,1.323 true 2.406,1.396 2.406,3.219 true 3.448,3.219 1.969,3.219 true 5.813,2.104 6.188,2.104 true 3.938,1.469 3.208,1.469 true 1.75,0.125 1.927,0.385 0.177,0.26 10 false *1 5.885,1.219 6.063,1.479 0.177,0.26 10 false *1 6.25,2 6.427,2.26 0.177,0.26 10 false *2 5.135,0.125 5.313,0.385 0.177,0.26 10 false *2 1.771,3.115 1.948,3.375 0.177,0.26 10 false *3 3.031,1.365 3.208,1.625 0.177,0.26 10 false *4

Text in Illustration
*1 Oil Delivery Pipe *2 Cylinder Head Cover
*3 Cylinder Head Cover Gasket *4 Oil Filler Housing



b.

Cylinder Head Gasket RH and No. 2 Cylinder Head Gasket LH

i.

Steel-laminate type cylinder head gaskets are used. A shim is used around the cylinder bore of each gasket to help enhance sealing performance and durability.

W102708E02
1.948,1.417 2.135,1.656 2.135,1.656 2.323,1.656 true 1.948,2.448 2.135,2.219 2.135,2.219 2.323,2.219 true 5.188,1.896 5.375,2.125 5.375,2.125 5.563,2.125 true 1.031,0.156 1.198,0.302 0.167,0.146 10 false *A 1.031,2.021 1.198,2.167 0.167,0.146 10 false *B 2.771,0.781 2.885,0.927 0.115,0.146 10 false A 3.385,0.781 3.51,0.927 0.125,0.146 10 false A 2.354,1.552 2.521,1.698 0.167,0.146 10 false *1 2.354,2.115 2.521,2.26 0.167,0.146 10 false *1 4.646,1.021 4.813,1.167 0.167,0.146 10 false *a 5.594,2.021 5.76,2.167 0.167,0.146 10 false *2

Text in Illustration
*A For Right Bank *B For Left Bank
*1 Cylinder Head Gasket *2 Shim
*a A - A Cross Section - -
V100135

Engine Front - -



c.

Cylinder Head Sub-assembly RH and Cylinder Head Sub-assembly LH

i.

The cylinder structure is simplified by separating the cam journal portion (camshaft housing sub-assembly) from the cylinder head.


ii.

The cylinder head, which is made of aluminum, contains pentroof-type combustion chambers. The spark plug is located in the center of the combustion chamber in order to improve the engine's anti-knock performance.


iii.

The intake ports are on the inside and the exhaust ports on the outside of the left and right banks respectively.


iv.

A taper squish combustion chamber is used to improve anti-knock performance and intake efficiency. In addition, engine performance and fuel economy are improved.


v.

Siamese type intake ports are used to reduce the overall surface area of the intake port walls. This prevents the fuel from adhering to the intake port walls, thus reducing HC exhaust emissions.

W102079E03
1.271,2.156 1.625,1.135 1.625,1.135 1.823,1.135 true 1.271,2.542 1.625,3.563 1.625,3.563 1.823,3.563 true 1.083,2.396 0.667,3.563 0.667,3.563 0.479,3.563 true 4.5,1.813 4.104,1.135 4.104,1.135 3.948,1.135 true 5.063,2.958 5.063,3.479 true 5.063,3.208 5.656,3.208 5.656,3.208 5.656,2.969 true 6.083,2.51 6.219,2.875 6.219,2.875 6.396,2.875 true 0.344,0.708 0.542,0.875 0.198,0.167 10 false *a 3.844,0.708 4.042,0.875 0.198,0.167 10 false *b 1.188,1.021 1.323,1.198 0.135,0.177 10 false A 1.188,3.344 1.302,3.542 0.115,0.198 10 false A 1.854,1.031 2.031,1.229 0.177,0.198 10 false *1 1.865,3.458 2.042,3.656 0.177,0.198 10 false *2 0.281,3.458 0.458,3.688 0.177,0.229 10 false *3 3.76,1.031 3.927,1.208 0.167,0.177 10 false *4 6.417,2.771 6.594,2.938 0.177,0.167 10 false *5 5,3.49 5.167,3.667 0.167,0.177 10 false *6

Text in Illustration
*1 Intake Valve *2 Exhaust Valve
*3 Spark Plug Hole *4 Camshaft Housing
*5 Upright Intake Port *6 Taper Squish Area
*a View from Bottom *b A - A Cross Section
V100135

Exhaust Side
V100136

Intake Side

HINT:

The difference between a siamese type intake port and independent type one is shown in the illustration.


W102107E04
0.479,0.594 0.677,0.792 0.198,0.198 10 false *A 3.917,0.594 4.115,0.792 0.198,0.198 10 false *B

Text in Illustration
*A Siamese Type *B Independent Type



d.

Cylinder Block Sub-assembly

i.

The cylinder block sub-assembly is made of aluminum alloy, so it is lightweight.


ii.

The cylinder block sub-assembly has a bank angle of 60°, a bank offset of 36.6 mm (1.441 in.) and a bore pitch of 105.5 mm (4.15 in.), resulting in a compact block (length and width) for its displacement.


iii.

Installation bosses for the 2 knock control sensors are located on the inside of the left and right banks.

W102080E03
5.354,1.656 5.354,0.51 true 5.531,2.01 5.531,0.51 5.531,0.51 4.656,0.51 true 4.469,0.406 4.635,0.698 0.167,0.292 10 false *1 4.74,3.385 6.021,3.677 1.281,0.292 10 false 105.5 mm (4.15 in.) 3.979,2.979 4.615,3.698 0.635,0.719 10 false 36.6 mm (1.441 in.) 1.052,0.667 1.292,0.969 0.24,0.302 10 false 60°

Text in Illustration
*1 Knock Control Sensor Boss - -


iv.

A water passage has been provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.

W102081E02
5.365,1.823 4.677,3 4.677,3 4.052,3 true 3.875,2.896 4.073,3.052 0.198,0.156 10 false *1

Text in Illustration
*1 Water Passage - -


v.

A compact block has been achieved by producing the thin cast-iron liners and cylinder block sub-assembly as a unit. It is not possible to rebore a block which uses this type of liner.


vi.

The liners are a spiny-type, which have been manufactured so that their casting exterior forms a large irregular surface in order to enhance the adhesion between the liners and the aluminum cylinder block. The enhanced adhesion helps improve heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.

W102082E02
5.802,0.729 5.521,0.729 5.521,0.729 5.24,1.458 true 5.708,2.208 6.188,2.208 true 4.51,2.771 4.76,2.771 4.76,2.771 5.229,2.271 true 4.094,0.5 4.26,0.656 0.167,0.156 10 false *a 5.844,0.625 6,0.792 0.156,0.167 10 false *1 6.24,2.104 6.417,2.271 0.177,0.167 10 false *2 4.333,2.667 4.5,2.833 0.167,0.167 10 false *3 3.406,1.198 3.531,1.365 0.125,0.167 10 false A 2.719,1.365 2.844,1.531 0.125,0.167 10 false A

Text in Illustration
*1 Cylinder Block *2 Irregularly shaped outer casting surface of liner
*3 Liner - -
*a A - A Cross Section - -


vii.

The temperature in the intake side of the cylinder bore tends to be lower. For this reason, a wide cylinder block water jacket spacer covers the cylinder bores in order to suppress the flow of the engine coolant and prevent excessive cooling. On the other hand, the temperature of the exhaust side of the cylinder bore tends to be higher. A cylinder block water jacket spacer covers the lower area of the cylinder bores in order to direct the engine coolant to the upper area of the cylinder bores where the temperature is higher. This makes the temperature around the cylinder bores more uniform. As a result, the viscosity of the engine oil (which lubricates the area between the wall surface of the cylinder bore and the piston) decreases, thus reducing friction between the cylinder bore and the piston.

W100637E02
2.24,1.531 2.24,0.677 2.24,0.677 1.656,0.677 true 1.885,1.323 1.885,0.677 true 5.74,1.271 5.74,1.021 5.74,1.021 4.833,1.021 true 5.063,1.677 5.063,1.031 true 5.458,2.344 5.458,3.073 5.458,3.073 6.458,3.073 true 6.073,1.885 6.073,3.073 true 1.469,0.573 1.656,0.802 0.188,0.229 10 false *1 6.479,2.969 6.688,3.219 0.208,0.25 10 false *1 4.635,0.917 4.833,1.135 0.198,0.219 10 false *2 4.615,2.25 4.833,2.49 0.219,0.24 10 false *a 6.292,1.156 6.573,1.406 0.281,0.25 10 false *b

Text in Illustration
*1 Cylinder Block Water Jacket Spacer *2 Water Jacket
*a Exhaust Side *b Intake Side
V100135

Engine Front - -



e.

Piston

i.

The pistons are made of aluminum alloy.


ii.

The top of the pistons use a taper squish shape to achieve fuel combustion efficiency.


iii.

The piston skirt is coated with resin to reduce friction losses.


iv.

The groove of the top ring is coated with alumite to ensure abrasion resistance.


v.

By increasing the machining precision of the cylinder bore diameter in the block, only one size piston is required.

W102083E03
5.698,0.844 5.385,0.313 5.385,0.313 3.385,0.313 true 4.188,0.844 3.875,0.313 true 5.802,0.906 6.281,1.146 6.281,1.146 6.281,1.99 true 2.667,1.76 3.094,1.896 3.094,1.896 3.094,2.229 true 1.844,1.094 1.406,0.229 1.406,0.229 1.115,0.229 true 0.917,0.125 1.135,0.302 0.219,0.177 10 false *1 3.208,0.208 3.427,0.385 0.219,0.177 10 false *3 3.021,2.24 3.24,2.417 0.219,0.177 10 false *2 6.198,2.021 6.417,2.198 0.219,0.177 10 false *4

Text in Illustration
*1 Front Mark *2 Resin Coating
*3 Taper Squish Shape *4 Alumite Coating



f.

Connecting Rod Sub-assembly

i.

Connecting rod sub-assemblies that have been forged for high strength are used for weight reduction.


ii.

Knock pins are used at the mating surfaces of the connecting rod caps to minimize the shifting of the connecting rod caps during assembly.


iii.

Nutless-type plastic region tightening bolts are used on the connecting rod sub-assemblies for a lighter design.


iv.

Aluminum bearings are used for the connecting rod bearings.


v.

The connecting rod bearings are reduced in width to reduce friction.

W100011E08
4.01,2.583 4.292,1.781 4.292,1.781 4.542,1.781 true 3.26,3 3.26,3.208 3.26,3.208 4.01,3.208 true 4.01,3 4.01,3.458 true 4.583,1.688 4.771,1.875 0.188,0.188 10 false *2 3.948,3.49 4.125,3.646 0.177,0.156 10 false *1

Text in Illustration
*1 Plastic Region Tightening Bolt *2 Knock Pin



g.

Crankshaft

i.

A crankshaft made of forged steel, which excels in rigidity and wear resistance, is used.


ii.

The crankshaft has 4 main bearing journals and 5 balance weights.

W102084E02
3.469,1.698 3.469,2.438 true 4.323,1.688 4.323,2.427 true 5.25,1.688 5.25,2.427 true 2.552,1.688 2.552,2.427 true 4.438,0.333 4.573,0.333 4.573,0.333 5.063,0.708 true 4.26,0.229 4.438,0.385 0.177,0.156 10 false *1 2.479,2.438 2.656,2.594 0.177,0.156 10 false *2 3.406,2.438 3.583,2.594 0.177,0.156 10 false *3 4.25,2.438 4.427,2.594 0.177,0.156 10 false *4 5.177,2.438 5.354,2.594 0.177,0.156 10 false *5

Text in Illustration
*1 Balance Weight *2 No.1 Journal
*3 No.2 Journal *4 No.3 Journal
*5 No.4 Journal - -
V100135

Engine Front - -



h.

Crankshaft Bearing and Crankshaft Bearing Cap

i.

The crankshaft main bearings are made of aluminum alloy.


ii.

Similar to the connecting rod bearings, the lining surface of the crankshaft bearings is micro-grooved to realize an optimal amount of oil clearance. As a result, cold-engine cranking performance is improved and engine vibration is reduced.


iii.

The upper crankshaft bearings have an oil groove around the inside circumference.


iv.

The crankshaft bearing caps are tightened using 4 plastic region tightening bolts for each journal. In addition, each cap is tightened laterally to improve its reliability.

U146674E04
1.563,4.104 1.729,4.104 1.729,4.104 2.104,2.688 true 2.938,3.198 2.938,3.74 true 5.74,3.156 5.74,3.583 true 6.083,0.885 6.302,0.885 6.302,0.885 6.302,1.719 true 4.719,1.323 4.927,1.323 4.927,1.323 5.469,1.875 true 4.927,1.615 5.01,1.615 5.01,1.615 5.354,1.927 true 1.865,1.406 1.865,0.417 true 2.229,1.677 2.229,0.417 true 2.688,0.313 2.896,0.521 0.208,0.208 10 false *1 2.865,3.75 3.094,3.927 0.229,0.177 10 false *3 4.729,1.51 4.885,1.729 0.156,0.219 10 false *7 4.552,1.219 4.719,1.396 0.167,0.177 10 false *6 5.667,3.583 5.896,3.792 0.229,0.208 10 false *5 5.906,0.792 6.063,1 0.156,0.208 10 false *4 1.385,4 1.615,4.219 0.229,0.219 10 false *2

Text in Illustration
*1 Plastic Region Tightening Bolt *2 Crankshaft Bearing Cap
*3 Seal Washer *4 Upper Crankshaft Bearing
*5 Lower Crankshaft Bearing *6 Oil Groove
*7 Micro-grooved surface - -



i.

Crankshaft Pulley

i.

The rigidity of the crankshaft pulley with its built-in torsional damper rubber reduces noise.

W102706E02
3.802,0.542 4.229,0.542 true 4.281,0.438 4.438,0.594 0.156,0.156 10 false *1

Text in Illustration
*1 Torsional Damper Rubber - -



j.

Oil Pan

i.

The No. 1 oil pan is made of aluminum alloy.


ii.

The No. 2 oil pan is made of steel.


iii.

The No. 1 oil pan is secured to the cylinder block sub-assembly and the transaxle housing to increase rigidity.

W102094E02
4.26,1.115 4.51,0.688 4.51,0.688 4.75,0.688 true 2.354,2.521 1.917,2.833 1.917,2.833 1.594,2.833 true 2.365,0.521 2.49,0.667 0.125,0.146 10 false A 4.594,2.771 4.719,2.917 0.125,0.146 10 false A 1.396,2.729 1.563,2.885 0.167,0.156 10 false *2 4.792,0.583 4.958,0.74 0.167,0.156 10 false *1 1.396,3.417 1.604,3.573 0.208,0.156 10 false *a

Text in Illustration
*1 No.1 Oil Pan *2 No.2 Oil Pan
*a A - A Cross Section - -
V100145

Oil Passage - -



k.

Valve Mechanism

i.

Each cylinder of this engine has 2 intake valves and 2 exhaust valves. Intake and exhaust efficiency is increased due to the larger total port areas.


ii.

This engine uses roller rocker arms with built-in needle bearings. This reduces the friction that occurs between the cams and the roller rocker arms when the valves are pushed down, thus improving fuel economy.


iii.

Hydraulic valve lash adjuster assemblies, which maintain a constant zero valve clearance through the use of oil pressure and spring force, are used.


iv.

The intake camshafts are driven by the crankshaft via the primary timing chain. The exhaust camshafts are each driven by the intake camshaft of their respective bank via a secondary chain.


v.

This engine has the dual Variable Valve Timing-intelligent (VVT-i) system which controls the intake camshafts and exhaust camshafts to provide optimal valve timing according to driving conditions. With this adoption, lower fuel consumption, higher engine performance, and fewer exhaust emissions have been achieved. For details of Dual VVT-i control.

W102087E03
5.781,1.594 5.781,1.094 true 5.802,1.99 6.031,2.198 6.031,2.198 6.24,2.198 true 5.49,1.969 5.271,1.708 5.271,1.708 5.021,1.708 true 5.396,2.229 5.125,1.99 5.125,1.99 4.958,1.99 true 5.323,2.625 5.635,2.938 5.635,2.938 5.833,2.938 true 5.74,3.833 5.448,3.833 5.448,3.833 5.031,3.323 true 5.135,2.813 4.854,2.813 true 2.719,1.198 3.552,0.375 3.552,0.375 3.896,0.375 true 3.375,1.802 4.271,1.135 4.271,1.135 4.646,1.135 true 1.51,1.375 1.802,0.438 1.802,0.438 1.969,0.438 true 0.844,3.646 1.063,3.646 1.063,3.646 1.635,3.083 true 1.688,1.615 2.813,4.573 2.813,4.573 3.177,4.573 true 2.677,2.625 3.656,4.292 3.656,4.292 3.927,4.292 true 2.979,2.448 4.219,3.875 4.219,3.875 4.552,3.875 true 5.698,0.896 5.896,1.052 0.198,0.156 10 false *4 6.281,2.094 6.458,2.271 0.177,0.177 10 false *5 2,0.333 2.188,0.521 0.188,0.188 10 false *1 3.948,0.271 4.125,0.427 0.177,0.156 10 false *2 4.677,1.031 4.854,1.188 0.177,0.156 10 false *3 4.594,3.771 4.844,3.927 0.25,0.156 10 false *11 3.958,4.188 4.135,4.344 0.177,0.156 10 false *1 3.219,4.469 3.458,4.625 0.24,0.156 10 false *12 0.583,3.542 0.833,3.698 0.25,0.156 10 false *13 4.844,1.604 5.021,1.76 0.177,0.156 10 false *6 4.76,1.885 4.938,2.042 0.177,0.156 10 false *7 5.875,2.833 6.031,2.99 0.156,0.156 10 false *8 4.677,2.708 4.854,2.865 0.177,0.156 10 false *9 5.771,3.729 6,3.885 0.229,0.156 10 false *10

Text in Illustration
*1 No. 2 Chain Sub-assembly (Secondary) *2 No. 1 Camshaft (RH, Intake)
*3 No. 3 Camshaft (LH, Intake) *4 Roller Valve Rocker Arm Sub-assembly
*5 Hydraulic Valve Lash Adjuster Assembly *6 Valve Spring Retainer
*7 Valve Spring *8 Valve Guide Bush
*9 Valve Spring Seat *10 Valve
*11 No. 4 Camshaft (LH, Exhaust) *12 No. 2 Camshaft (RH, Exhaust)
*13 No. 1 Chain Sub-assembly (Primary) - -



l.

Valve Timing

W102108E05
2.906,0.896 2.396,0.354 2.396,0.354 1.854,0.354 false 3.49,0.917 3.958,0.521 3.958,0.521 4.313,0.521 false 2.188,2.781 1.896,3.021 1.896,3.021 1.635,3.021 false 3.844,2.833 4.188,3.104 4.188,3.104 4.677,3.104 false 3.313,0.771 3.656,0.365 3.656,0.365 3.958,0.365 false 3.156,0.771 3.5,0.177 3.5,0.177 3.667,0.177 false 2.375,0.708 2.688,0.865 0.313,0.156 10 false 29° 3.781,0.771 4.094,0.927 0.313,0.156 10 false 39° 2.302,3.083 2.615,3.24 0.313,0.156 10 false 31° 1.667,2.313 1.979,2.469 0.313,0.156 10 false 71° 4.208,2.563 4.521,2.719 0.313,0.156 10 false 60° 3.594,3.146 3.906,3.302 0.313,0.156 10 false 25° 0.406,0.25 1.844,0.938 1.438,0.688 10 false Intake VVT-i Operation Range 4.375,0.417 5.948,1.104 1.573,0.688 10 false Exhaust VVT-i Operation Range 4.719,3 6.292,3.688 1.573,0.688 10 false Exhaust VVT-i Operation Range 0.198,2.906 1.615,3.563 1.417,0.656 10 false Intake VVT-i Operation Range 2.948,3.438 3.271,3.604 0.323,0.167 10 false BDC 2.958,0.417 3.281,0.573 0.323,0.156 10 false TDC 4,0.25 4.313,0.406 0.313,0.156 10 false 11° 3.729,0.073 4.042,0.229 0.313,0.156 10 false 4° 5.021,1.771 7.115,2.135 2.094,0.365 10 false : Exhaust Valve Operation Range 5.031,1.375 7.031,1.729 2,0.354 10 false : Intake Valve Operation Range


m.

Camshaft

i.

The camshafts are made of cast iron alloy.


ii.

Oil passages are provided on the intake and exhaust camshafts in order to supply engine oil to the VVT-i system.


iii.

Camshaft timing gear assemblies (LH and RH) and camshaft timing exhaust gear assemblies (LH and RH) are installed on the front of the camshafts to vary the timing of the intake and exhaust valves.


iv.

Together with the use of the roller rocker arms, the cam profile has been modified. This results in increased valve lift when the valve begins to open and as it finishes closing, helping to achieve enhanced output performance.

W102109E04
5.771,2.24 5.771,1.604 true 5.781,1.792 6.219,1.792 6.219,1.792 6.219,1.604 true 0.958,1.563 1.521,0.635 1.521,0.635 2.156,0.635 true 1.771,1.542 2.146,0.948 2.146,0.948 2.469,0.948 true 1.667,2.063 1.219,2.479 1.219,2.479 0.885,2.479 true 1.802,2.333 1.469,2.927 1.469,2.927 1.094,2.927 true 3.094,1.698 3.438,1.167 3.438,1.167 3.927,1.167 true 2.813,2.75 2.333,3.167 2.333,3.167 1.896,3.167 true 2.979,3.01 2.5,3.719 2.5,3.719 2.104,3.719 true 3.688,3.594 4.156,4.156 4.156,4.156 4.667,4.156 true 4.417,3.24 4.865,3.521 4.865,3.521 5.188,3.521 true 4.875,2.354 5.198,2.604 5.198,2.604 5.76,2.604 true 2.177,0.531 2.406,0.729 0.229,0.198 10 false *1 2.521,0.844 2.781,1.063 0.26,0.219 10 false *2 3.958,1.063 4.219,1.302 0.26,0.24 10 false *3 5.813,2.5 6.156,2.75 0.344,0.25 10 false *6 5.229,3.417 5.531,3.688 0.302,0.271 10 false *7 4.708,4.052 4.99,4.333 0.281,0.281 10 false *8 1.927,3.615 2.271,3.875 0.344,0.26 10 false *5 1.708,3.063 2,3.313 0.292,0.25 10 false *4 0.719,2.375 0.948,2.563 0.229,0.188 10 false *4 0.917,2.823 1.271,3.156 0.354,0.333 10 false *5 5.708,2.24 5.948,2.458 0.24,0.219 10 false *9 5.281,0.813 5.531,1.104 0.25,0.292 10 false *a

Text in Illustration
*1 Camshaft Timing Exhaust Gear Assembly RH *2 No. 2 Camshaft (RH, Exhaust)
*3 No. 1 Camshaft (RH, Intake) *4 Timing Rotor
*5 Camshaft Timing Gear Assembly *6 No. 3 Camshaft (LH, Intake)
*7 No. 4 Camshaft (LH, Exhaust) *8 Camshaft Timing Exhaust Gear Assembly LH
*9 Modified profile of camshaft lobe - -
*a Increased Valve Lift - -



n.

Camshaft Timing Gear Assembly (Intake)

i.

The intake camshaft timing gears each consist of an outer housing that is driven by the timing chain sprocket, and a vane sub-assembly that is coupled to each camshaft.


ii.

The camshaft timing gear assembly uses a vane sub-assembly with 3 lobes.


iii.

When the engine stops, each intake camshaft timing gear assembly is locked at the most retarded angle by its lock pin. This ensures excellent engine startability.


iv.

The oil pressure sent from the advance or retard side passages of the intake camshafts causes rotation of the vane sub-assembly relative to the timing chain sprocket, to vary the valve timing continuously.

W102110E04
3.385,1.969 3.75,0.927 3.75,0.927 4.083,0.927 true 3.458,2.563 4.229,3.323 4.229,3.323 4.563,3.323 true 2.323,2.875 2.521,3.479 2.521,3.479 2.813,3.479 true 1.313,3.156 1.25,3.542 1.25,3.542 1.083,3.542 true 4.563,2.313 5.219,2.688 5.219,2.688 5.51,2.688 true 5.146,1.844 5.5,2.042 5.5,2.042 5.885,2.042 true 0.281,0.688 0.438,0.854 0.156,0.167 10 false *a 1.708,0.688 1.865,0.854 0.156,0.167 10 false *b 0.906,3.438 1.063,3.615 0.156,0.177 10 false *2 2.854,3.375 3.01,3.552 0.156,0.177 10 false *3 4.125,0.823 4.281,1 0.156,0.177 10 false *1 4.615,3.219 4.813,3.427 0.198,0.208 10 false *4 5.552,2.583 5.771,2.813 0.219,0.229 10 false *5 5.917,1.938 6.073,2.115 0.156,0.177 10 false *6

Text in Illustration
*1 Lock Pin *2 Timing Rotor
*3 Outer Housing *4 Vane Sub-assembly [Coupled to Outer Housing Camshaft (Intake)]
*5 Timing Chain Sprocket *6 Camshaft (Intake)
*a Engine Operating *b Engine Stopped
V100135

Oil Pressure - -



o.

Camshaft Timing Exhaust Gear Assembly

i.

The camshaft timing exhaust gear assembly consists of an outer housing that is driven by the timing chain sprocket, and a vane sub-assembly that is coupled to each camshaft.


ii.

The camshaft timing exhaust gear assembly use a vane sub-assembly with 4 lobes.


iii.

When the engine stops, the camshaft timing exhaust gear assembly is locked at the most advanced angle. This ensures excellent engine startability.


iv.

The oil pressure sent from the advance or retard side passages of the exhaust camshafts causes rotation of the vane sub-assembly relative to the timing chain sprocket, to vary the valve timing continuously.


v.

An advance assist spring is provided on the camshaft timing exhaust gear assembly. This helps to apply torque in the advance angle direction so that the vane lock pin securely engages with the housing when the engine stops.

W102118E03
2.5,2.938 2.5,3.375 true 3.542,2.604 3.542,3.125 true 4.479,2.49 4.479,2.844 true 5.354,1.906 5.354,2.656 true 1.896,2.26 1.448,1.813 1.448,1.813 1.208,1.813 true 3.5,2.198 4.167,0.979 4.167,0.979 4.375,0.979 true 2.438,3.375 2.594,3.542 0.156,0.167 10 false *3 3.458,3.115 3.615,3.281 0.156,0.167 10 false *4 4.406,2.833 4.563,3 0.156,0.167 10 false *5 5.281,2.656 5.438,2.823 0.156,0.167 10 false *6 4.406,0.875 4.573,1.042 0.167,0.167 10 false *1 1.031,1.708 1.198,1.875 0.167,0.167 10 false *2 0.667,0.375 0.844,0.552 0.177,0.177 10 false *a 2.115,0.375 2.292,0.552 0.177,0.177 10 false *b

Text in Illustration
*1 Lock Pin *2 Advance Assist Spring
*3 Outer Housing *4 Vane Sub-assembly [Coupled to Camshaft (Exhaust)]
*5 Timing Chain Sprocket *6 Camshaft (Exhaust)
*a Engine Operating *b Engine Stopped
V100135

Oil Pressure - -



p.

Chain Sub-assembly and Chain Tensioner Sub-assembly

i.

The primary and secondary chains are roller chains with a pich of 9.525 mm (0.375 in.).


ii.

All chain sub-assemblies are lubricated by an oil jet.


iii.

The primary chain uses a chain tensioner sub-assembly and each of the secondary chains use a No. 2 chain tensioner sub-assembly.


iv.

Both types of chain tensioner use a spring and oil pressure to maintain proper chain tension at all times. They suppress noise generated by the chains.


v.

The chain tensioner sub-assembly (primary) is a ratcheting type with a non-return mechanism.

W102089E03
3.615,2.177 3.615,0.865 true 4.521,1.844 4.969,2.75 4.969,2.75 5.167,2.75 true 3.979,2.698 4.333,3.521 4.333,3.521 4.542,3.521 true 3.604,3.292 3.604,3.677 true 3.281,3 2.917,3.604 2.917,3.604 2.75,3.604 true 0.823,1.958 0.646,2.135 0.646,2.135 0.521,2.135 true 0.906,1.875 1.146,1.875 true 0.875,1.677 1.135,1.677 true 0.844,1.625 0.521,1.625 true 1.521,3.635 1.677,3.792 1.677,3.792 1.771,3.792 true 1.313,3.583 1.083,3.844 1.083,3.844 0.958,3.844 true 0.958,3.302 0.594,2.938 0.594,2.938 0.448,2.938 true 1.427,3.208 1.688,2.938 1.688,2.938 1.813,2.938 true 5.948,1.938 5.552,1.938 true 5.958,1.792 5.552,1.792 true 6,1.823 6.219,1.823 true 6.094,2.042 6.219,2.042 true 1.469,3.323 1.677,3.229 1.677,3.229 1.802,3.229 true 1.281,3.24 1,2.74 1,2.74 0.865,2.74 true 0.188,0.979 0.375,1.167 0.188,0.188 10 false *a 0.188,2.604 0.375,2.792 0.188,0.188 10 false *b 5.177,0.979 5.365,1.167 0.188,0.188 10 false *c 3.542,0.677 3.708,0.844 0.167,0.167 10 false *1 3.51,3.667 3.719,3.833 0.208,0.167 10 false *2 2.583,3.5 2.792,3.667 0.208,0.167 10 false *5 4.573,3.417 4.781,3.583 0.208,0.167 10 false *4 0.344,1.521 0.552,1.688 0.208,0.167 10 false *6 1.188,1.573 1.396,1.74 0.208,0.167 10 false *8 1.188,1.771 1.396,1.938 0.208,0.167 10 false *9 0.344,2.031 0.552,2.198 0.208,0.167 10 false *7 1.854,2.833 2.063,3 0.208,0.167 10 false *7 1.854,3.125 2.063,3.292 0.208,0.167 10 false *6 0.219,2.833 0.469,3 0.25,0.167 10 false *10 1.802,3.688 2.042,3.854 0.24,0.167 10 false *12 0.719,3.74 0.958,3.906 0.24,0.167 10 false *11 5.365,1.688 5.573,1.854 0.208,0.167 10 false *6 5.365,1.833 5.573,2 0.208,0.167 10 false *9 6.25,1.719 6.458,1.885 0.208,0.167 10 false *8 6.25,1.938 6.458,2.104 0.208,0.167 10 false *7 5.188,2.646 5.396,2.813 0.208,0.167 10 false *3 0.688,2.635 0.854,2.802 0.167,0.167 10 false *9

Text in Illustration
*1 Idle Sprocket Assembly *2 Chain Sub-assembly (Primary)
*3 No. 2 Chain Sub-assembly (Secondary) *4 No. 1 Chain Vibration Damper
*5 Chain Tensioner Slipper *6 Ball
*7 Plunger *8 Ball Spring
*9 Main Spring *10 Sub Spring
*11 Cam Spring *12 Cam
*a No. 2 Chain Tensioner Sub-assembly (Secondary) *b No. 3 Chain Tensioner Sub-assembly (Secondary)
*c No. 1 Chain Tensioner Sub-assembly (Primary) - -



q.

Hydraulic Valve Lash Adjuster Assembly

i.

The hydraulic lash adjusters, which are located at the fulcrum (pivot point) of the roller rocker arms, each consist primarily of a plunger, plunger spring, check ball, and check ball spring.


ii.

Both the engine oil that is supplied by the cylinder head and the built-in spring actuate the hydraulic valve lash adjuster assembly. The oil pressure and the spring force that act on the plunger push the roller No. 1 valve rocker arm sub-assembly against the cam, in order to adjust the clearance between the valve stem and the roller No. 1 valve rocker arm. This prevents the generation of noise during the opening and closing of the valves. As a result, engine noise is reduced.

W102090E03
4.146,0.406 4.469,0.406 4.469,0.406 4.583,0.833 true 1.24,1.135 2,1.135 true 1.229,1.875 1.906,1.875 true 1.229,2.302 1.542,2.302 1.542,2.302 2.135,2.479 true 4.49,1.698 3.656,0.792 3.656,0.792 3.302,0.792 true 3.719,0.594 4.021,0.594 4.021,0.594 4.542,1.49 true 2.094,2.76 2.521,3.135 2.521,3.135 2.771,3.135 true 4.844,1.281 5.396,0.521 5.396,0.521 5.531,0.521 true 1.229,2.698 1.5,2.698 1.5,2.698 2.135,2.625 true 1.052,1.031 1.25,1.229 0.198,0.198 10 false *1 1.052,1.771 1.344,2.031 0.292,0.26 10 false *2 1.052,2.198 1.313,2.417 0.26,0.219 10 false *3 1.052,2.594 1.396,2.865 0.344,0.271 10 false *4 2.813,3.031 3.135,3.25 0.323,0.219 10 false *5 3.563,0.49 3.74,0.688 0.177,0.198 10 false *7 3.146,0.688 3.406,0.896 0.26,0.208 10 false *6 3.969,0.302 4.292,0.552 0.323,0.25 10 false *8 5.573,0.417 5.844,0.646 0.271,0.229 10 false *9

Text in Illustration
*1 Plunger *2 Oil Passage
*3 Check Ball *4 Check Ball Spring
*5 Plunger Spring *6 Oil Passage
*7 Hydraulic Valve Lash Adjuster Assembly *8 Cam
*9 Roller Valve Rocker Arm Sub-assembly - -



r.

V-ribbed Belt

i.

Accessory components are driven by a serpentine belt consisting of a single V-ribbed belt. It reduces the overall engine length, weight and number of engine parts.


ii.

An automatic tensioner eliminates the need for tension adjustment.

W102105E03
1.01,3.281 2.833,3.281 2.833,3.281 3.188,2.677 true 4.292,1.813 5.146,1.094 5.146,1.094 5.448,1.094 true 4.76,1.802 5.083,1.531 5.083,1.531 5.448,1.531 true 4.552,2.771 4.813,3.115 4.813,3.115 5.448,3.115 true 4.198,2.229 5.448,2.229 true 3.958,2.99 4.229,3.521 4.229,3.521 5.448,3.521 true 1.01,2.729 2.594,2.729 2.594,2.729 2.948,2.333 true 1.01,1.583 3.073,1.583 3.073,1.583 3.406,1.854 true 2.104,2.104 1.01,2.104 true 5.51,0.99 5.677,1.135 0.167,0.146 10 false *1 5.51,1.427 5.677,1.573 0.167,0.146 10 false *2 5.51,2.125 5.677,2.271 0.167,0.146 10 false *3 5.51,3.01 5.677,3.156 0.167,0.146 10 false *4 5.51,3.417 5.677,3.563 0.167,0.146 10 false *5 0.802,1.479 0.969,1.625 0.167,0.146 10 false *9 0.802,2 0.969,2.146 0.167,0.146 10 false *8 0.802,2.625 0.969,2.771 0.167,0.146 10 false *7 0.802,3.177 0.969,3.323 0.167,0.146 10 false *6

Text in Illustration
*1 Belt Idler Pulley (No.3) *2 Alternator Pulley
*3 Idler Pulley for Automatic Tensioner *4 Air Conditioning Compressor Pulley
*5 Belt Idler Pulley (No.1) *6 Crankshaft Pulley
*7 Belt Idler Pulley (No.2) *8 Power Steering Pump Pulley
*9 Water Pump Pulley - -


iii.

The tension of the V-ribbed belt is properly maintained by the tension spring that is enclosed in the belt tensioner assembly.

W102106E04
1.448,1.229 1.615,0.969 1.615,0.969 1.844,0.969 true 2.073,1.938 2.406,1.375 2.406,1.375 2.552,1.375 true 1.854,2.813 1.344,2.813 true 2.969,3.188 2.969,2.833 true 4.542,2.188 5.167,2.75 5.167,2.75 5.469,2.75 true 0.49,0.688 0.667,0.865 0.177,0.177 10 false *a 1.885,0.865 2.042,1.01 0.156,0.146 10 false *1 2.594,1.271 2.75,1.417 0.156,0.146 10 false *2 1.156,2.708 1.313,2.854 0.156,0.146 10 false *3 2.885,3.177 3.042,3.323 0.156,0.146 10 false *4 5.5,2.646 5.677,2.823 0.177,0.177 10 false *b

Text in Illustration
*1 Idler Pulley *2 Spring
*3 Arm *4 Bracket
*a Cross Section *b Fulcrum
V100135

Belt Tensioner Pulling Direction
V100136

Belt Pulling Direction