Home › Engine / Hybrid System › 1GR-FE LUBRICATION › LUBRICATION SYSTEM
NM1440E _51 Engine / Hybrid System _056084 1GR-FE LUBRICATION _0273703 LUBRICATION SYSTEM UN GENERAL/CONTROL/DETAILS F

1GR-FE LUBRICATION  LUBRICATION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Oil Pump

i.

A compact cycloid rotor type oil pump directly driven by the crankshaft is used.


ii.

This oil pump uses an internal relief method which circulates relief oil to the suction passage in the oil pump. This aims to minimize oil level change in the oil pan, reduce friction, and reduce the air mixing rate in the oil.

W102185E03
5.188,2.698 5.188,2.854 true 5.979,2.708 5.979,2.865 true 5.875,1.25 6,0.99 6,0.99 6.104,0.99 true 0.604,1.625 0.969,0.656 0.969,0.656 1.146,0.656 true 2.104,2.656 2.104,3.156 true 2.708,2.677 2.708,3.177 true 6.135,0.885 6.406,1.104 0.271,0.219 10 false *d 4.615,0.865 4.885,1.083 0.271,0.219 10 false *a 1.177,0.552 1.448,0.771 0.271,0.219 10 false *1 2.031,3.167 2.302,3.385 0.271,0.219 10 false *2 2.625,3.167 2.896,3.385 0.271,0.219 10 false *3 5.906,2.865 6.177,3.083 0.271,0.219 10 false *c 5.125,2.865 5.542,3.25 0.417,0.385 10 false *b

Text in Illustration
*1 Timing Chain Cover Sub-assembly *2 Oil Pump Rotor (Cycloid Rotor)
*3 Oil Pump Cover - -
*a Oil Passage In The Oil Pump *b To Oil Filter
*c From Oil Strainer Sub-assembly *d To Cylinder Block Sub-assembly



b.

No. 1 Oil Nozzle Sub-assembly

i.

Oil nozzles are provided in the center of the right and left banks of the cylinder block for cooling and lubricating the pistons.


ii.

These oil nozzles contain a check valve to prevent oil from being fed when the oil pressure is low. This prevents the overall oil pressure in the engine from dropping.

U150611E02
1.531,1.99 3.219,0.25 3.219,0.25 2.188,2.115 true 2.5,2.125 3.219,0.25 3.219,0.25 3.938,0.25 true 3.229,0.969 3.323,0.677 3.323,0.677 3.938,0.677 true 5.49,2.219 5.01,1.563 5.01,1.563 4.698,1.563 true 3.99,0.146 4.25,0.396 0.26,0.25 10 false *1 3.969,0.573 4.229,0.823 0.26,0.25 10 false *2 4.51,1.458 4.771,1.708 0.26,0.25 10 false *3 4.198,1.146 4.458,1.396 0.26,0.25 10 false *a

Text in Illustration
*1 Oil Nozzle Sub-assembly *2 Cylinder Block Sub-assembly
*3 Check Ball - -
*a Oil Nozzle Sub-assembly Cross Section - -
V100135

Oil - -



c.

Oil Filter

i.

An oil filter with a replaceable oil filter element is used. The oil filter element uses a high-performance filter paper to improve filtration performance. It is also combustible for environmental protection.


ii.

The resin filter cap sub-assembly is used to reduce weight.


iii.

This oil filter has a structure which can allow the draining of the oil remaining in the oil filter. This prevents oil from spattering when replacing the oil filter element and allows the technician to work without touching hot oil.

U150612E03
3.719,3.865 3.844,4.25 3.844,4.25 4.125,4.25 true 3.333,3.833 3.604,4.635 3.604,4.635 4.125,4.635 true 5.354,4.135 5.875,4.135 true 4.073,3.031 4.198,2.688 4.198,2.688 4.458,2.688 true 1.51,1.927 2,2.417 2,2.417 2.25,2.417 true 2.25,2.927 1.542,2.927 true 2.25,4.396 1.438,4.396 true 2.25,4.979 1.208,4.979 true 4.5,2.583 4.781,2.823 0.281,0.24 10 false *2 4.146,4.146 4.427,4.385 0.281,0.24 10 false *4 4.146,4.531 4.427,4.771 0.281,0.24 10 false *3 5.167,4.031 5.448,4.271 0.281,0.24 10 false *5 2.271,2.313 2.573,2.594 0.302,0.281 10 false *1 2.281,2.823 2.583,3.104 0.302,0.281 10 false *2 2.281,4.292 2.583,4.573 0.302,0.281 10 false *3 2.281,4.875 2.583,5.156 0.302,0.281 10 false *4 4.865,2.625 5.146,2.865 0.281,0.24 10 false *a

Text in Illustration
*1 Oil Filter Case *2 Oil Filter Element
*3 Filter Cap Sub-assembly *4 Drain Plug
*5 Drain Pipe - -
*a When Draining Oil - -
V100135

Oil - -

HINT:
·

The oil in the oil filter can be drained by removing the drain plug and inserting the drain pipe supplied with the oil filter element into the oil filter. For details, refer to the Repair Manual.

·

The engine oil maintenance interval for a model that has an oil filter with a replaceable oil filter element is the same as that for a conventional model.