Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2009.08–2013.08
NM1440E _52 Drivetrain _056088 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0273707 AUTOMATIC TRANSMISSION SYSTEM UN GENERAL/CONTROL/DETAILS F

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The electronic control system of the A750F automatic transmission consists of the control functions listed below:

System Function
Clutch Pressure Control
·

Controls the pressure that is applied directly to B2 brake and C3 clutch by actuating the linear solenoid valves SL1 and SL2 in accordance with the ECM signals.

·

The solenoid valve SLT and SL1 minutely control the clutch pressure in accordance with the engine output and driving conditions.


Line Pressure Control Based on the throttle opening angle and various signals, the ECM sends a signal to solenoid valve SLT to generate line pressure that varies according to the engine output and to allow smooth gear changes.
Lock-up Timing Control The ECM sends current to the solenoid valve SLU based on signals from various sensors and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control
·

Controls the solenoid valve SLU, provides an intermediate mode between the ON/OFF operation of the lock-up clutch, and increases the operating range of the lock-up clutch to improve fuel economy.

·

The flex lock-up clutch control operates in 3rd, 4th and 5th gears in both D and S5 range, 3rd and 4th gears in the S4 range and 3rd gears in the S3 range.


Artificial Intelligence Shift Control
(AI-shift Control)
Based on the signals from various sensors, the ECM determines the road condition and the intention of the driver. While the pattern select switch is in POWER, the shift pattern is biased toward sporty driving. Thus, an appropriate shift pattern is automatically determined to improve drivability.
Multi-mode Automatic Transmission
·

The ECM appropriately controls the automatic transmission in accordance with the range position selected while the shift lever is in S.


Fail-safe If a malfunction is detected in the sensors or solenoids, the ECM performs fail-safe control to prevent the vehicle's drivability from being affected significantly.
Diagnosis When the ECM detects a malfunction, the ECM makes a diagnosis and memorizes the information that relates to the fault.


b.

Clutch to Clutch Pressure Control

i.

This control is adopted for shifting from 4th to 5th gear and from 5th to 4th gear.


ii.

Solenoid valves SL1 and SL2 are actuated in accordance with the signals from the ECM, and guides this output pressure directly to the control valves B1 and C1 in order to regulate the line pressure that acts on the B1 brake and C1 clutches. As a result, responsive and excellent shift characteristics are realized.

X101965E06
3.01,2.146 2.823,2.146 2.823,2.146 2.823,2.438 true 1.125,2.146 0.938,2.146 0.938,2.146 0.938,2.438 true 3.01,1.313 3.333,1.646 0.323,0.333 10 false SL2 3.083,2.042 3.917,2.719 0.833,0.677 9 false Brake Control Valve 1.177,2.042 2.052,2.74 0.875,0.698 9 false Clutch Control Valve 1.5,2.979 1.875,3.396 0.375,0.417 10 false C1 3.385,2.979 3.771,3.438 0.385,0.458 10 false B1 0.313,4.073 1.646,4.542 1.333,0.469 9 false Line Pressure 1.115,1.313 1.438,1.646 0.323,0.333 10 false SL1 4.313,2.125 4.76,2.521 0.448,0.396 10 false ECM 5.333,0.698 7.083,1.188 1.75,0.49 10 false INPUT SPEED SENSOR 5.323,1.208 7.156,1.667 1.833,0.458 10 false OUTPUT SPEED SENSOR 5.323,1.677 6.708,2.375 1.385,0.698 10 false ATF TEMPERATURE SENSOR 5.302,2.313 6.719,2.969 1.417,0.656 10 false THROTTLE POSITION SENSOR 5.323,3.052 7.156,3.51 1.833,0.458 10 false MASS AIR FLOW METER 5.313,3.563 6.979,4.448 1.667,0.885 10 false ENGINE COOLANT TEMPERATURE SENSOR



c.

Clutch Pressure Optimal Control

i.

The ECM monitors the signals from various sensors, such as the speed sensor NT, allowing shift solenoid valves SLT and SL1 to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics have been realized.

X101966E06
2.542,2.635 3.104,2.635 3.104,2.635 3.583,3.281 true 3.719,4.063 3.719,4.281 3.719,4.281 2.948,4.281 true 4.094,4.063 4.094,5.135 true 4.604,3.24 5.135,3.24 true 5.052,3.563 4.688,3.563 4.688,3.563 4.24,4.031 true 0.958,2.531 2.542,2.938 1.583,0.406 10 false INPUT SPEED SENSOR 0.667,4.177 2.979,4.615 2.313,0.438 10 false ACCUMULATOR CONTROL VALVE 3.49,5.146 4.646,6.042 1.156,0.896 10 false SHIFT SOLENOID VALVE SLT, SL1 5.188,3.135 7.156,3.646 1.969,0.51 10 false OUTPUT SPEED SENSOR 5.135,3.458 7.156,4.083 2.021,0.625 10 false ATF TEMPERATURE SENSOR 6.521,6.083 7.01,6.479 0.49,0.396 10 false Time 4.979,4.99 5.427,5.979 0.448,0.99 10 false Output Shaft Torque 1.406,6.083 2.854,6.5 1.448,0.417 10 false Solenoid Drive Signal 0.292,4.906 1.104,5.604 0.813,0.698 10 false Clutch/Brake Pressure 2.198,1.938 2.833,2.417 0.635,0.479 10 false Time 5.74,0.917 6.281,1.417 0.542,0.5 10 false ECM 1.104,1.667 3.01,2.115 1.906,0.448 10 false Practical rpm Change Ratio 1.865,0.698 2.719,1.313 0.854,0.615 10 false Target rpm Change Ratio 0.573,0.573 0.917,1.51 0.344,0.938 10 false Input Shaft rpm



d.

Line Pressure Optimal Control

i.

Through the use of the solenoid valve SLT, the line pressure is optimally controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter and the transmission.


ii.

Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition, and the ATF temperature, thus realizing smooth shift characteristics and optimizing the workload of the oil pump (reducing unnecessary parasitic losses).

X101607E08
0.677,0.167 1.646,0.469 0.969,0.302 10 false Line Pressure 1.792,0.938 2.417,1.448 0.625,0.51 10 false Primary Regulator 0.396,2.792 0.844,3 0.448,0.208 10 false Pump 1.594,3.802 2.167,4.208 0.573,0.406 10 false Fluid Pressure 2.458,4.771 2.99,5.073 0.531,0.302 10 false Current 3.771,0.823 5.75,1.24 1.979,0.417 10 false Solenoid Valve Drive Signal 3.313,3.333 4.229,3.75 0.917,0.417 10 false Shift Solenoid Valve SLT 5.531,1.583 6.99,1.885 1.458,0.302 10 false Input Turbine Speed 5.521,2.021 6.823,2.313 1.302,0.292 10 false ATF Temperature 5.573,2.448 6.823,2.75 1.25,0.302 10 false Shift Position 5.573,2.885 6.823,3.188 1.25,0.302 10 false Gear Position 5.573,3.344 7,3.896 1.427,0.552 10 false Throttle Valve Opening Angle 5.573,4.167 6.823,4.469 1.25,0.302 10 false Intake Air Mass 5.573,5.063 6.552,5.552 0.979,0.49 10 false Engine Coolant Temperature 5.573,4.615 6.823,4.917 1.25,0.302 10 false Engine Speed 5.031,3.115 5.417,3.417 0.385,0.302 10 false ECM



e.

Flex Lock-up Clutch Control

i.

In the low-to-mid-speed range, this flex lock-up clutch control regulates the solenoid valve SLU to provide an intermediate mode between the ON/OFF operation of the lock-up clutch in order to improve the energy transmitting efficiency in this range. As a result, the operating range of the lock-up clutch is increased and fuel economy is improved. The flex lock-up clutch control operates in 3rd, 4th and 5th gears when the shift lever is in D or in the S5 range, and in 4th gear when the shift lever is in the S4 range.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), the flex lock-up clutch control operates. Therefore, fuel-cut area of the engine has been expanded and fuel-economy has been improved.

X101959E08
3.635,0.344 4.198,0.813 0.563,0.469 10 false ECM 0.438,1.552 1.969,2.167 1.531,0.615 10 false ACCELERATOR PEDAL POSITION SENSOR 4.531,1.427 4.99,1.885 0.458,0.458 10 false Engine Speed 5.635,0.938 6.542,1.313 0.906,0.375 10 false Engine Speed Signal 5.125,2.208 6.083,2.563 0.958,0.354 10 false Vehicle Speed 6.125,3.021 6.688,3.688 0.563,0.667 10 false Linear Solenoid Signal 4.698,3.167 5.385,3.604 0.688,0.438 10 false Current 5.542,3.698 6.115,4.146 0.573,0.448 10 false Time 0.406,3.438 1.656,4.146 1.25,0.708 10 false ENGINE COOLANT TEMPERATURE SENSOR 6.083,1.802 6.927,2.49 0.844,0.688 10 false Transmission Revolution Signal 0.354,2.906 2.365,3.479 2.01,0.573 10 false THROTTLE POSITION SENSOR 0.167,5.198 1.427,5.75 1.26,0.552 10 false CRANKSHAFT POSITION SENSOR 0.24,5.729 3.146,6.156 2.906,0.427 10 false TRANSMISSION REVOLUTION SENSOR (NT) 1.604,6.094 3.417,6.521 1.813,0.427 10 false LOCK-UP CONTROL VALVE 4.615,6.083 6.677,6.531 2.063,0.448 10 false LOCK-UP CONTROL SOLENOID ASSEMBLY (SLU) 4.969,5.729 6.969,6.135 2,0.406 10 false ATF TEMPERATURE SENSOR

X100038E20
2.646,0.865 2.385,0.865 2.385,0.865 2.938,2.021 true 4.365,0.292 4.115,0.292 4.115,0.292 4.667,1.656 true 1.542,0.656 1.917,1.104 0.375,0.448 10 false Large 4.76,2.24 5.281,2.677 0.521,0.438 10 false High 1.906,2.25 2.948,2.719 1.042,0.469 10 false Vehicle Speed 2.917,2.385 4.365,3.104 1.448,0.719 10 false Flex Lock-up Operating Range (Deceleration) 4.417,0.188 6.354,0.823 1.938,0.635 10 false Lock-up Operating Range 2.708,0.76 4.177,1.583 1.469,0.823 10 false Flex Lock-up Operating Range (Acceleration) 2.458,3.104 4.396,3.479 1.938,0.375 10 false Flex Lock-up Operating Range 0.635,1.604 1.771,2.292 1.135,0.688 10 false Accelerator Pedal Depression Angle

Flex Lock-up Operation:
Gear Shift Lever Position or Range
D, S5 S4
1st X X
2nd X X
3rd ○*1 X
4th ○* ○*2
5th ○* -

HINT:

○: Operates

X: Does not operate

-: Not applicable

*1: Flex lock-up clutch control operates during acceleration.

*2: Flex lock-up clutch control operates during deceleration.




f.

Artificial Intelligence Shift Control (AI-shift Control)

i.

The automatic transaxle gear is determined by the shift pattern, which uses the vehicle speed and accelerator pedal depressing angle.


ii.

Additionally, AI-shift control enables the ECM to estimate the road conditions and the driver's intention in order to automatically control the shift pattern in the optimal manner. As a result, a comfortable ride has been achieved.


iii.

The AI-shift control includes road condition support control and driver's intention support control.


iv.

The AI-shift control determines optimal transaxle control based on input signals and automatically changes the shift pattern.

X101610E11
0.583,0.313 1.594,0.729 1.01,0.417 10 false Input Signals 0.563,0.948 1.615,1.354 1.052,0.406 10 false Sensor Signal 0.406,1.25 1.615,1.917 1.208,0.667 10 false - Accelerator Pedal Depression Angle 0.406,1.865 1.563,2.354 1.156,0.49 10 false - Vehicle Speed 0.406,2.302 1.625,2.74 1.219,0.438 10 false - Engine Speed 0.406,2.74 1.552,3.156 1.146,0.417 10 false - Brake Signal 0.385,3.771 1.854,4.229 1.469,0.458 10 false Calculated by ECM 0.354,4.104 1.844,4.635 1.49,0.531 10 false Vehicle Acceleration 2.292,0.792 3.229,1.042 0.938,0.25 10 true AI-shift Control 2.542,1.146 3.781,1.49 1.24,0.344 10 false Road Condition 2.719,1.5 4.333,1.885 1.615,0.385 10 false Uphill/Downhill Driving 3.115,1.844 4.75,2.25 1.635,0.406 10 false Estimating the Grade 2.344,2.188 2.938,2.458 0.594,0.271 10 false Small 3.573,2.427 4.156,2.813 0.583,0.385 10 false Large 2.75,2.76 4.406,3.24 1.656,0.479 10 false Criterion Acceleration 2.75,3.115 4.333,3.583 1.583,0.469 10 false Actual Acceleration 2.573,3.896 3.885,4.281 1.313,0.385 10 false Driver's Intention 2.333,4.833 3.729,5.292 1.396,0.458 10 false - Vehicle Condition 2.333,5.344 3.583,5.833 1.25,0.49 10 false - Acceleration Pedal Operation 4,5.125 5.031,5.552 1.031,0.427 10 false Estimating the Driver's Intention 5.844,0.385 7.01,0.958 1.167,0.573 10 false Basic Shift Pattern Control 5.844,2.385 6.833,2.906 0.99,0.521 10 false Road Condition Support Control 5.823,5.104 6.844,5.635 1.021,0.531 10 false Driver's Intention Support Control


v.

Under road condition support control, ECM determines the throttle opening angle and the vehicle speed whether the vehicle is being driven uphill or downhill. To achieve the optimal drive force while driving uphill, this control prevents unnecessary upshifts. To achieve the optimal engine brake effect while driving downhill, this control automatically performs downshifts.

X101969E05
4.177,3.104 4.177,2.625 4.177,2.625 4.052,2.625 false 5.958,3.604 6.99,4.031 1.031,0.427 10 false With Control 5.948,3.094 7.115,3.667 1.167,0.573 10 false Without Control 5.406,3.635 5.854,4.135 0.448,0.5 9 false 5th 4.802,3.635 5.156,4.042 0.354,0.406 9 false 4th 4.344,3.635 4.573,4.146 0.229,0.51 9 false 3rd 3.271,3.635 3.688,4.073 0.417,0.438 9 false 4th 1.625,3.635 1.948,4.094 0.323,0.458 9 false 4th 2.167,3.635 2.396,4.156 0.229,0.521 9 false 3rd 0.771,3.635 1.135,4.031 0.365,0.396 9 false 5th 0.771,3.146 1.135,3.656 0.365,0.51 9 false 5th 1.406,3.146 1.802,3.594 0.396,0.448 9 false 4th 1.844,3.146 2.229,3.583 0.385,0.438 9 false 5th 2.177,3.146 2.406,3.552 0.229,0.406 9 false 3rd 2.521,3.146 2.896,3.573 0.375,0.427 9 false 5th 2.875,3.146 3.25,3.604 0.375,0.458 9 false 4th 3.406,2.521 4.042,3.281 0.635,0.76 9 false 5th (Brake Operating)



g.

Multi-mode Automatic Transmission

i.

The driver can select the desired shift range by moving the shift lever to "+" (forwards) or to "-" (backwards) while in S.


ii.

The multi-mode automatic transmission is designed to allow the driver to switch the gear ranges.


iii.

An S mode indicator which illuminates when the shift lever is in S and a shift range indicator which indicates the shift range have been provided in the combination meter.

X101970E05
0.792,0.698 3.344,1.156 2.552,0.458 10 false COMBINATION METER ASSEMBLY 5.208,3.198 6.438,3.906 1.229,0.708 10 false TRANSMISSION CONTROL SWITCH 1.625,4.771 2.573,5.427 0.948,0.656 10 false Fluid Pressure Control Signals 0.323,4.76 1.344,5.354 1.021,0.594 10 false Ignition Advance Control 3.188,2.927 4.802,3.385 1.615,0.458 10 false S Mode Position Signal 3.188,3.417 4.521,3.906 1.333,0.49 10 false Shift-Up Signal 3.188,3.917 4.604,4.354 1.417,0.438 10 false Shift-Down Signal 2.021,2.219 3.073,2.667 1.052,0.448 10 false CAN (V Bus) 1.063,1.604 3.083,2.115 2.021,0.51 10 false Shift Range Indicator Light 1.177,1.167 2.906,1.583 1.729,0.417 10 false S Mode Indicator Light 1.781,3.25 2.406,3.698 0.625,0.448 10 false ECM 2.896,4.75 4.146,5.427 1.25,0.677 10 false Shift Solenoid Valve Control Signals


iv.

The driver selects the S mode position by engaging the shift lever. At this time, the shift range position selects the 4th or 5th range according to the vehicle speed. (During AI-shift control, the shift range that has the currently controlled gear position as the maximum usable gear position will be displayed.) Then, the shift range positions change one at a time, as the driver moves the shift lever to the front ("+" position) or to the rear ("-" position).


v.

Under this control, the ECM effects optimal shift control within the usable gear range that the driver has selected. As with an ordinary automatic transmission, it shifts to the 1st gear when the vehicle is stopped.


vi.

When the shift lever is in S, the S mode indicator light in the combination meter illuminates. The shift range indicator light indicates the state of the shift range position that the driver has selected.

X101971E02
5,2.563 5.271,2.833 0.271,0.271 10 false *b 2.167,0.927 2.438,1.198 0.271,0.271 10 false *a

Text in Illustration
*a Transition of Shift Ranges *b Shift Pattern
V100145

Default Shift Range - -

Usable Gear Chart
Shift Range Shift Range Indicator Indication Usable Gear
S5 5 5th ←→ 4th ←→ 3rd ←→ 2nd ←→ 1st
S4 4 4th ←→ 3rd ←→ 2nd ←→ 1st
S3 3 3rd ←→ 2nd ←→ 1st
S2 2 2nd ←→ 1st
S1 1 1st




FUNCTION


a.

Shift Lock System

i.

The shift lock mechanism prevents the shift lever from being moved to a position other than P, unless the ignition switch is on (IG), and the brake pedal is pressed. This mechanism helps to prevent unintended acceleration.


ii.

The shift lock system mainly consists of the shift lock ECU and shift lock override button.


iii.

Shift lock ECU has a built-in P detection switch, and shift lock solenoid.


iv.

The shift lock ECU uses the P detection switch to detect the shift lever position, and receives inputs from the stop light switch and the power source control ECU. Upon receiving these signals, the shift lock ECU turns on the shift lock solenoid in order to release the shift lock.


v.

A shift lock override button, which manually overrides the shift lock mechanism, is used.

X101972E05
5.427,1.563 6.385,2.24 0.958,0.677 10 false P DETECTION SWITCH 5.427,0.625 6.271,1.354 0.844,0.729 10 false SHIFT LOCK SOLENOID 0.75,0.438 2.49,0.958 1.74,0.521 10 false STOP LIGHT SWITCH 0.75,2.135 2.333,2.583 1.583,0.448 10 false IGNITION SWITCH 2.99,1.313 4.323,1.854 1.333,0.542 10 false SHIFT LOCK ECU 3.99,3.25 5.917,3.75 1.927,0.5 10 false SHIFT LEVER ASSEMBLY 4.885,2.552 6.438,3.146 1.552,0.594 10 false SHIFT LOCK SOLENOID ASSEMBLY




CONSTRUCTION


a.

Torque Converter

i.

A compact, lightweight and high-capacity torque converter is used. The torque converter supports flex lock-up clutch control, thus improving fuel economy.

U150617E03
2.708,0.979 3.406,0.979 true 3.781,0.833 3.781,0.438 3.781,0.438 2.708,0.438 true 3.917,1.854 4.979,1.854 true 3.917,1.427 4.979,1.427 true 4.146,1.083 4.979,1.083 true 2.521,0.333 2.75,0.51 0.229,0.177 10 false *1 2.51,0.875 2.74,1.052 0.229,0.177 10 false *2 5.021,0.979 5.25,1.156 0.229,0.177 10 false *3 5.021,1.323 5.25,1.5 0.229,0.177 10 false *4 5.01,1.75 5.24,1.927 0.229,0.177 10 false *5

Text in Illustration
*1 Turbine Runner *2 Lock-up Clutch
*3 Pump Impeller *4 Stator
*5 One-way Clutch - -



b.

Oil Pump

i.

The oil pump is operated by the torque converter. It lubricates the planetary gear units and supplies operating fluid pressure for hydraulic control.


ii.

The material of the pump cover is aluminum to reduce weight.

X101614E03
3.031,2.635 3.031,3.219 true 4.146,2.448 4.146,3.25 true 5.156,1.823 5.156,3.385 true 1.531,2.083 1.531,1.271 1.531,1.271 1.208,1.271 true 5.365,0.969 5.365,0.708 5.365,0.708 5.938,0.708 true 4.063,3.25 4.281,3.448 0.219,0.198 10 false *3 2.948,3.219 3.167,3.417 0.219,0.198 10 false *2 5.073,3.385 5.292,3.583 0.219,0.198 10 false *5 1.01,1.167 1.229,1.365 0.219,0.198 10 false *1 5.969,0.604 6.188,0.802 0.219,0.198 10 false *4

Text in Illustration
*1 Pump Body *2 Drive Gear
*3 Driven Gear *4 Pump Cover
*5 Stator Shaft - -



c.

ATF Filling Procedures

i.

The ATF filling procedure is changed in order to improve the accuracy of the ATF level when the transmission is being repaired or replaced. As a result, the oil filler tube and the oil level gauge used for a conventional automatic transmission are discontinued, eliminating the need to inspect the fluid level as a part of routine maintenance.


ii.

This filling procedure uses a refill plug, overflow plug, ATF temperature sensor, and shift indicator light "D".

X101999E03
5.438,2.594 5.438,3.146 true 1.542,2.167 1.542,2.917 true 1.927,1.344 2.115,1.656 0.188,0.313 10 false *1 5.385,3.156 5.573,3.469 0.188,0.313 10 false *2 1.458,2.906 1.646,3.219 0.188,0.313 10 false *a

Text in Illustration
*1 Refill Plug *2 Overflow Plug
*a Proper Level - -



d.

Planetary Gear Unit

i.

The planetary gear unit consists of 3 planetary gear units, 3 clutches, 4 brakes, and 3 one-way clutches.

U150618E03
3.417,1.177 3.417,0.396 3.417,0.396 2.927,0.396 true 3.771,1.167 3.771,0.156 3.771,0.156 2.917,0.156 true 2.063,1.833 2.063,3.51 true 4.104,2.083 4.104,3.51 true 4.469,2.021 4.469,3.51 true 5.042,2.031 5.042,3.51 true 4.115,1.188 4.115,0.365 4.115,0.365 5.281,0.365 true 3.729,2.083 3.729,3.51 true 3.458,2.219 3.458,3.49 true 3.281,6.427 3.281,6.604 true 4.5,6.365 4.5,6.604 true 5.073,5.938 5.073,6.604 true 5.573,6.365 5.573,6.604 true 5.281,0.917 4.938,0.917 4.938,0.917 4.938,1.198 true 6.656,5.969 6.656,6.375 true 2.323,6.052 2.323,6.375 true 0.531,5.927 0.531,6.26 true 3.917,1.406 3.917,0.135 3.917,0.135 5.271,0.135 true 3.219,1.188 3.219,0.635 3.219,0.635 2.938,0.635 true 1.99,3.51 2.208,3.833 0.219,0.323 10 false *1 3.375,3.5 3.594,3.823 0.219,0.323 10 false *2 3.615,3.5 3.854,3.823 0.24,0.323 10 false *10 3.99,3.5 4.229,3.823 0.24,0.323 10 false *12 4.375,3.5 4.615,3.823 0.24,0.323 10 false *13 4.948,3.5 5.188,3.823 0.24,0.323 10 false *14 2.75,0.531 2.969,0.708 0.219,0.177 10 false *3 2.75,0.292 2.969,0.469 0.219,0.177 10 false *4 2.75,0.052 2.969,0.229 0.219,0.177 10 false *7 5.344,0.26 5.563,0.438 0.219,0.177 10 false *5 5.344,0.438 5.563,0.615 0.219,0.177 10 false *6 5.344,0.635 5.604,0.813 0.26,0.177 10 false *11 5.344,0.813 5.604,0.99 0.26,0.177 10 false *8 3.177,6.583 3.49,6.771 0.313,0.188 10 false *12 4.375,6.583 4.688,6.771 0.313,0.188 10 false *13 4.969,6.583 5.281,6.771 0.313,0.188 10 false *16 5.469,6.583 5.781,6.771 0.313,0.188 10 false *14 6.542,6.375 6.854,6.698 0.313,0.323 10 false *17 2.208,6.385 2.521,6.708 0.313,0.323 10 false *15 0.469,6.271 0.781,6.594 0.313,0.323 10 false *1 5.344,0.031 5.563,0.208 0.219,0.177 10 false *9

Text in Illustration
*1 Input Shaft *2 No.1 Clutch
*3 No. 2 Clutch *4 No. 3 Clutch
*5 No. 1Brake *6 No. 2Brake
*7 No. 3Brake *8 No. 4 Brake
*9 No. 1 One-way Clutch *10 No. 2 One-way Clutch
*11 No. 3 One-way Clutch *12 Front Planetary Gear
*13 Center Planetary Gear *14 Rear Planetary Gear
*15 Sun Gear *16 Intermediate Shaft
*17 Output Shaft - -


ii.

The functions of the clutches and brakes are as follows:

Component Function
C1 No. 1 Clutch Connects the input shaft and intermediate shaft.
C2 No. 2 Clutch Connects the input shaft and center planetary carrier.
C3 No. 3 Clutch Connects the input shaft and front sun gear.
B1 No. 1 Brake Prevents the front planetary carrier from turning either clockwise or counterclockwise.
B2 No. 2 Brake Prevents the front and the center ring gear from turning either clockwise or counterclockwise.
B3 No. 3 Brake Prevents outer race of F2 from turning both clockwise and counterclockwise.
B4 No. 4 Brake Prevents center planetary carrier and the rear ring gear from turning either clockwise or counterclockwise.
F1 No. 1 One-way Clutch Prevents the front planetary carrier from turning counterclockwise.
F2 No. 2 One-way Clutch When B3 is operating, the one-way clutch prevents the front sun gear from turning counterclockwise.
F3 No. 3 One-way Clutch Prevents the center planetary carrier and the rear ring gear from turning counterclockwise.
Planetary Gears These gears change the route through which driving force is transmitted, in accordance with the operation of each clutch and brake, in order to increase or reduce the output shaft speed.



e.

Centrifugal Fluid Pressure Canceling Mechanism

i.

The centrifugal fluid pressure canceling mechanism is used on clutches C1, C2 and C3.


ii.

Clutch shifting operation is affected not only by the valve body controlling fluid pressure but also by centrifugal fluid pressure that is present due to fluid in the clutch piston oil pressure chamber. The centrifugal fluid pressure canceling mechanism uses chamber B to reduce this effect applied to the chamber A. As a result, smooth shifting with excellent response has been achieved.

X101976E03
1.083,1.885 0.771,2.729 true 1.833,2.26 2.156,2.708 true 0.792,1.063 0.958,1.063 0.958,1.063 1.125,1.615 true 1.865,1.396 2.052,1.063 2.052,1.063 2.188,1.063 true 0.594,0.958 0.875,1.26 0.281,0.302 10 false *1 2.25,0.958 2.531,1.26 0.281,0.302 10 false *2 2.135,2.698 2.417,3 0.281,0.302 10 false *4 0.656,2.729 0.938,3.031 0.281,0.302 10 false *3

Text in Illustration
*1 No.1 Clutch Piston *2 No.1 Clutch
*3 Chamber A *4 Chamber B



f.

Chamber B is filled by fluid supplied to the shaft for lubrication. As a result of filling chamber B, there is the same amount of fluid pressure due to centrifugal force on both sides of the piston. This cancels the effect of fluid pressure on the piston due to centrifugal force. Accordingly, it is not necessary to discharge the fluid through the use of a check ball, and highly responsive and smooth shifting characteristics are achieved.

X101686E06
2.938,1.604 3.427,1.604 true 1.146,1.5 1.75,1.5 true 3.979,0.74 3.979,0.396 3.979,0.396 3.698,0.396 true 2.219,2.458 2.219,2.646 false 1.99,2.323 1.99,2.448 1.99,2.448 2.208,2.448 false 2.49,2.323 2.49,2.448 2.49,2.448 2.208,2.448 false 3.25,0.281 3.708,0.615 0.458,0.333 10 false Clutch 3.5,1.49 4.698,2.115 1.198,0.625 10 false Chamber B (Centrifugal Fluid Pressure Chamber) 0.313,1.385 1.125,2.271 0.813,0.885 10 false Chamber A (Piston Fluid Pressure Chamber) 1.521,2.656 2.594,3.146 1.073,0.49 10 false Fluid Pressure Applied to Piston 2.833,2.76 3.563,3.094 0.729,0.333 10 false Shaft Side 0.729,3.729 1.781,4.115 1.052,0.385 10 false Fluid pressure applied to piston 2.563,3.729 4.094,4.125 1.531,0.396 10 false Centrifugal fluid pressure applied to chamber B 4.896,3.729 6.406,4.135 1.51,0.406 10 false Target fluid pressure (original clutch pressure) 2.146,3.813 2.344,4.042 0.198,0.229 10 false - 4.479,3.823 4.708,4 0.229,0.177 10 false = 5.167,0.51 6.906,0.938 1.74,0.427 10 false : Target Fluid Pressure 5.167,1.198 5.26,1.5 0.094,0.302 10 false : 5.24,1.208 6.854,1.781 1.615,0.573 10 false Centrifugal Fluid Pressure Applied to Chamber A 5.167,1.938 6.906,2.365 1.74,0.427 10 false : Centrifugal Fluid Pressure


g.

Valve Body Unit

i.

The valve body consists of the upper (No. 1 and No. 2) and lower (No. 1 and No. 2) valve bodies and 7 solenoid valves.

X101977E03
4.292,0.698 4.333,0.635 4.333,0.635 4.875,0.635 true 3.729,0.635 3.979,0.292 3.979,0.292 4.865,0.292 true 3.25,0.49 3.177,0.323 3.177,0.323 2.75,0.323 true 2.875,4.354 2.771,4.521 2.771,4.521 2.115,4.521 true 4.896,3.635 5.208,4.313 5.208,4.313 5.948,4.313 true 5.344,3.75 5.438,3.979 5.438,3.979 5.948,3.979 true 3.49,4.271 3.625,4.521 3.625,4.521 4.094,4.521 true 1.938,4.417 2.146,4.646 0.208,0.229 10 false *1 4.135,4.417 4.344,4.646 0.208,0.229 10 false *2 5.99,4.208 6.198,4.438 0.208,0.229 10 false *4 5.99,3.875 6.198,4.104 0.208,0.229 10 false *6 4.917,0.531 5.125,0.76 0.208,0.229 10 false *3 4.917,0.188 5.125,0.417 0.208,0.229 10 false *5 2.573,0.219 2.781,0.448 0.208,0.229 10 false *7

Text in Illustration
*1 Shift Solenoid Valve SLT *2 Shift Solenoid Valve SL1
*3 Shift Solenoid Valve SR *4 Shift Solenoid Valve S1
*5 Shift Solenoid Valve SLU *6 Shift Solenoid Valve S2
*7 Shift Solenoid Valve SL2 - -

X101978E02
1.948,2.448 1.219,2.448 true 2,1.104 2,0.375 true 3.24,1.302 3.24,0.385 true 3.469,1.302 3.469,0.385 true 4.698,1.229 4.698,0.396 true 4.927,1.302 4.927,0.396 true 5.427,1.281 5.427,0.375 true 4.313,2.75 4.313,3.25 true 4,2.563 4,3.25 true 3.677,2.781 3.677,3.25 true 3.229,2.813 3.229,3.281 true 2.396,2.698 2.396,3.25 true 1.031,2.344 1.292,2.583 0.26,0.24 10 false *7 1.927,0.188 2.188,0.427 0.26,0.24 10 false *1 3.167,0.188 3.427,0.427 0.26,0.24 10 false *2 3.406,0.188 3.667,0.427 0.26,0.24 10 false *3 4.625,0.188 4.885,0.427 0.26,0.24 10 false *4 4.865,0.188 5.125,0.427 0.26,0.24 10 false *5 5.375,0.188 5.635,0.427 0.26,0.24 10 false *6 4.229,3.25 4.49,3.427 0.26,0.177 10 false *12 3.906,3.25 4.167,3.427 0.26,0.177 10 false *11 3.583,3.25 3.844,3.427 0.26,0.177 10 false *10 3.156,3.25 3.417,3.427 0.26,0.177 10 false *9 2.313,3.25 2.573,3.427 0.26,0.177 10 false *8

Text in Illustration (No. 1 Upper Valve Body:)
*1 B1 Accumulator *2 Clutch Lock Valve
*3 Solenoid Modulator Valve *4 2 - 3 Shift Valve
*5 1 - 2 Shift Valve *6 B1 Apply Control Valve
*7 Secondary Regulator Valve *8 Lock-up Relay Valve
*9 Lock-up Control Valve *10 C3 Check Valve
*11 3 - 4 Shift Valve *12 Brake Control Valve

X101979E03
4.417,2.01 5.24,2.01 true 5.271,1.906 5.531,2.146 0.26,0.24 10 true *1

Text in Illustration (No. 2 Upper Valve Body:)
*1 Coast Brake Relay Valve - -

X101980E03
1.99,2.073 1.052,2.073 true 2.229,2.052 2.229,3.24 true 3.365,2 2.781,3.25 true 4.063,2 4.063,3.271 true 3.563,2.208 3.563,3.25 true 4.313,1.896 4.927,3.26 true 0.875,1.969 1.198,2.271 0.323,0.302 10 false *1 2.146,3.25 2.469,3.552 0.323,0.302 10 false *2 2.667,3.25 2.99,3.552 0.323,0.302 10 false *3 3.5,3.25 3.823,3.552 0.323,0.302 10 false *4 4,3.26 4.323,3.563 0.323,0.302 10 false *5 4.927,3.25 5.25,3.552 0.323,0.302 10 false *6

Text in Illustration (Lower Valve Body:)
*1 SLT Damper *2 Primary Regulator Valve
*3 Clutch Control Valve *4 Clutch Apply Control Valve
*5 Accumulator Control Valve *6 Sequence Valve



h.

Solenoid Valve SL1, SL2, SLT and SLU

i.

In order to provide hydraulic pressure in proportion to current that flows to the solenoid coil, the solenoid valve SL1, SL2, SLT, and SLU linearly controls the line pressure and clutch and brake engagement pressure based on the signals received from the ECM.

X101981E05
2.75,0.26 2.948,0.26 2.948,0.26 3.125,0.917 true 2.104,1.396 2.26,1.396 2.26,1.396 2.479,1.094 true 4.646,0.219 4.521,0.219 4.521,0.219 4.219,0.708 true 4.708,0.115 6.24,0.594 1.531,0.479 10 false SOLENOID COIL 2.698,1.417 4.365,1.792 1.667,0.375 10 false SOLENOID VALVE SLT 3.896,2.885 4.5,3.531 0.604,0.646 10 false Hydraulic Pressure 2.51,4.365 3.313,4.719 0.802,0.354 10 false Current 5.938,4.354 6.74,4.708 0.802,0.354 10 false Current 0.5,2.906 1.094,3.594 0.594,0.688 10 false Hydraulic Pressure 1.76,0.156 3.094,0.531 1.333,0.375 10 false SPOOL VALVE 1.5,1.292 2.135,1.594 0.635,0.302 10 false SLEEVE 4.813,2.198 6.656,2.698 1.844,0.5 10 false SOLENOID VALVE SLU 0.729,2.188 3.615,2.604 2.885,0.417 10 false SOLENOID VALVE SLU SL1, SL2 and SLT

Solenoid Valve Function
SL1
·

Clutch pressure control.

·

Accumulator back pressure control.


SL2 Brake pressure control.
SLT
·

Line pressure control.

·

Accumulator back pressure control.


SLU
·

Lock-up clutch pressure control.





i.

Solenoid Valve S1, S2 and SR

i.

These solenoid valves are 3-way solenoid valves. A filter is provided at the tip of the solenoid valve to further improve operational reliability.

X101982E06
1.365,1.271 1.365,0.885 1.365,0.885 1.229,0.885 true 1.073,4.604 1.448,4.604 true 1.448,1.875 2.01,2.5 0.563,0.625 10 false Control Pressure 0.885,0.781 1.49,1.188 0.604,0.406 10 false Filter 1.76,2.531 3,3.021 1.24,0.49 10 false OFF Condition 4.875,2.521 6.063,2.979 1.188,0.458 10 false ON Condition 4.469,1.875 5.052,2.458 0.583,0.583 10 false Control Pressure 4.542,0.792 5.167,1.26 0.625,0.469 10 false Drain 0.104,0.104 1.927,0.677 1.823,0.573 10 false SOLENOID VALVE S1 0.177,3.344 1.875,3.875 1.698,0.531 10 false SOLENOID VALVE S2 1.792,5.271 3.198,5.646 1.406,0.375 10 false OFF Condition 4.896,5.281 6.156,5.635 1.26,0.354 10 false ON Condition 4.167,3.792 4.74,4.344 0.573,0.552 10 false Control Pressure 3.635,4.344 4.198,5.063 0.563,0.719 10 false Line Pressure 0.719,4.5 1.24,4.906 0.521,0.406 10 false Filter

Solenoid Valve Type Function
S1 3-way
·

Switches the 2-3 shift valve.


S2 3-way
·

Switches the 1-2 shift valve.

·

Switches the 3-4 shift valve.


SR 3-way
·

Switches the clutch apply control valve.





j.

ATF Temperature Sensor No.1 and No.2

i.

ATF temperature sensor No.1 (THO1) is used for hydraulic pressure control. This sensor is used for revision of the pressure that is used to apply clutches and brakes in the transmission. This helps to ensure smooth shift quality.


ii.

ATF temperature sensor No.2 (THO2) is used as a basis for modifying the ECT shift timing control when the ATF temperature is high. It is also used for the ATF temp. warning light.

X101983E06
3.208,1.833 3.208,2.417 true 3.219,0.448 3.219,1.146 true 3.125,0.24 3.354,0.479 0.229,0.24 10 false *1 3.156,2.438 3.385,2.677 0.229,0.24 10 false *2

Text in Illustration
*1 ATF Temperature Sensor No.1 *2 ATF Temperature Sensor No.2
V100135

Front - -



k.

Speed Sensors

i.

This automatic transmission uses a speed sensor NT and speed sensor SP2. Thus, the ECM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to the various conditions.


ii.

These speed sensors are a pick-up coil type.


iii.

The speed sensor NT detects the input speed of the transmission. The C3 clutch drum is used as the timing rotor for this sensor.


iv.

The speed sensor SP2 detects the speed of the output shaft. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.

X101984E03
3.813,2.094 4.042,2.948 4.042,2.948 4.177,2.948 true 4.771,1.875 5.417,2.198 5.417,2.198 5.667,2.198 true 4.115,1.469 4.917,0.479 4.917,0.479 5.104,0.479 true 2.052,0.344 2.531,0.344 2.531,0.344 3.365,1.469 true 5.156,0.375 5.438,0.677 0.281,0.302 10 false *4 5.698,2.094 6.042,2.417 0.344,0.323 10 false *3 4.219,2.844 4.5,3.146 0.281,0.302 10 false *1 1.865,0.24 2.177,0.51 0.313,0.271 10 false *2

Text in Illustration
*1 Speed Sensor NT *2 C3 Clutch Drum (Timing Rotor)
*3 Parking Gear (Timing Rotor) *4 Speed Sensor SP2



l.

Park/Neutral Position Switch

i.

The park/neutral position switch sends the P, R, N, D and STAR position signals to the ECM. It also sends signals for the shift position indicator light (P, R, N, and D).

X101985E04
0.802,3.958 2.031,4.458 1.229,0.5 10 false To IG1 RELAY 4.458,0.656 7.104,1.333 2.646,0.677 10 false COMBINATION METER ASSEMBLY 4.698,1.156 6.802,1.677 2.104,0.521 10 false Shift Position Indicator Light 0.635,1.74 1,1.948 0.365,0.208 10 false P 1.125,1.74 1.49,1.948 0.365,0.208 10 false R 1.594,1.74 1.958,1.948 0.365,0.208 10 false N 2.052,1.74 2.417,1.948 0.365,0.208 10 false D 2.51,1.74 2.875,1.948 0.365,0.208 10 false STA 1.365,1.042 1.833,1.365 0.469,0.323 10 false ECM 3.094,1.229 4.198,1.75 1.104,0.521 10 false CAN (V Bus) 0.625,2.646 1.104,3 0.479,0.354 10 false PL 1.104,2.646 1.583,2.969 0.479,0.323 10 false RL 1.583,2.646 2.073,2.99 0.49,0.344 10 false NL 2.042,2.646 2.51,2.927 0.469,0.281 10 false DL 2.51,3.677 2.875,3.885 0.365,0.208 10 false B 2.5,2.646 2.958,2.875 0.458,0.229 10 false L



m.

Transmission Control Switch

i.

The transmission control switch detects whether the shift lever is in D or S, and detects the operating conditions of the shift lever (+ position or - position) if the S mode is selected, and sends signals to the ECM. At this time, the ECM turns on the shift range indicator light for the selected range.

X101986E04
1.563,0.604 1.698,0.604 1.698,0.604 1.698,1.156 true 5.104,1.729 6.979,2.146 1.875,0.417 10 false Shift Range Indicator Light 5.167,0.969 6.688,1.573 1.521,0.604 10 false COMBINATION METER ASSEMBLY 0.292,0.49 1.531,1.167 1.24,0.677 10 false TRANSMISSION CONTROL SWITCH 5.229,2.177 6.885,2.625 1.656,0.448 10 false S Mode Indicator Light 0.5,1.344 0.958,1.99 0.458,0.646 10 false IG1 RELAY 1.115,1.5 1.531,1.865 0.417,0.365 10 false IG 2.073,1.49 2.396,1.792 0.323,0.302 10 false S 2.073,1.854 2.615,2.177 0.542,0.323 10 false SFTU 2.073,2.208 2.688,2.563 0.615,0.354 10 false SFTD 2.708,1.854 3.229,2.229 0.521,0.375 10 false SFTU 2.708,2.208 3.292,2.615 0.583,0.406 10 false SFTD 3.365,1.75 3.885,2.135 0.521,0.385 10 false ECU 4.052,1.927 5.063,2.333 1.01,0.406 10 false CAN (V Bus) 2.948,1.49 3.271,1.792 0.323,0.302 10 false S



n.

Automatic Transmission Fluid (ATF) WS

i.

TOYOTA genuine ATF WS is used to reduce the resistance of the ATF and improve the fuel economy by reducing its viscosity in the practical operating temperature range. At higher fluid temperatures, the viscosity is the same as that of TOYOTA genuine ATF Type T-IV, to ensure the durability of the automatic transmission.

X100046E22
1.531,1.198 1.698,0.771 1.698,0.771 1.948,0.771 true 0.854,0.917 1.156,1.292 0.302,0.375 10 false High 3.229,2.24 3.531,2.615 0.302,0.375 10 false High 4.167,2.208 5.104,2.583 0.938,0.375 10 false Temperature 2.01,0.646 3.229,0.875 1.219,0.229 10 false Reduced Viscosity 0.646,0.458 1.271,0.771 0.625,0.313 10 false Viscosity 4.542,0.104 6.74,0.365 2.198,0.26 10 false : TOYOTA Genuine ATF Type T-IV 4.542,0.458 6.406,0.688 1.865,0.229 10 false : TOYOTA Genuine ATF WS




OPERATION


a.

Transmission Power Flow

X101993E05
3.74,0.208 5.052,0.594 1.313,0.385 10 false Solenoid Valve 2.302,0.604 2.719,0.969 0.417,0.365 10 false S1 3.021,0.604 3.479,0.958 0.458,0.354 10 false S2 3.792,0.604 4.219,0.99 0.427,0.385 10 false SR 4.521,0.594 5.021,0.958 0.5,0.365 10 false SL1 5.323,0.604 5.802,0.969 0.479,0.365 10 false SL2 6.083,0.594 6.604,0.958 0.521,0.365 10 false SLU 0.948,0.208 1.635,0.813 0.688,0.604 10 false Shift Lever Position 0.854,0.948 1.094,1.313 0.24,0.365 10 false P 1.458,0.948 1.865,1.313 0.406,0.365 10 false Park 0.854,1.302 1.094,1.667 0.24,0.365 10 false R 1.375,1.292 1.927,1.656 0.552,0.365 10 false Reverse 0.854,1.667 1.094,2.031 0.24,0.365 10 false N 1.385,1.646 1.938,2.01 0.552,0.365 10 false Neutral 1.51,2 1.813,2.365 0.302,0.365 10 false 1st 1.51,2.354 1.813,2.719 0.302,0.365 10 false 2nd 1.521,2.719 1.823,3.083 0.302,0.365 10 false 3rd 1.521,3.063 1.823,3.427 0.302,0.365 10 false 4th 1.521,3.406 1.938,3.729 0.417,0.323 10 false 5th 1.51,3.76 1.948,4.094 0.438,0.333 10 false 1st 1.51,4.104 1.938,4.51 0.427,0.406 10 false 2nd 1.521,4.458 1.927,4.823 0.406,0.365 10 false 3rd 1.531,4.823 1.958,5.208 0.427,0.385 10 false 4th 1.51,5.167 1.979,5.531 0.469,0.365 10 false 1st 1.51,5.531 1.99,5.896 0.479,0.365 10 false 2nd 1.521,5.875 1.99,6.25 0.469,0.375 10 false 3rd 1.51,6.229 1.927,6.604 0.417,0.375 10 false 1st 1.51,6.583 2,7 0.49,0.417 10 false 2nd 1.51,6.938 1.917,7.313 0.406,0.375 10 false 1st 0.76,2.625 1.135,3.219 0.375,0.594 10 false D,S5 0.823,4.313 1.198,4.906 0.375,0.594 10 false S4 0.833,5.51 1.333,6 0.5,0.49 10 false S3 0.833,6.385 1.208,6.979 0.375,0.594 10 false S2 0.813,6.948 1.323,7.385 0.51,0.438 10 false S1 0.865,7.344 1.76,7.708 0.896,0.365 10 false : Operates

X101994E05
0.875,0.104 1.677,0.302 0.802,0.198 10 false Shift Lever 2.438,0.104 2.948,0.302 0.51,0.198 10 false Clutch 1.354,0.802 1.75,1 0.396,0.198 10 false Park 0.781,0.813 0.979,1.01 0.198,0.198 10 false P 2.031,0.479 2.333,0.677 0.302,0.198 10 false C1 2.51,0.479 2.813,0.677 0.302,0.198 10 false C2 2.99,0.479 3.292,0.677 0.302,0.198 10 false C3 3.448,0.479 3.75,0.677 0.302,0.198 10 false B1 3.938,0.479 4.24,0.677 0.302,0.198 10 false B2 4.417,0.479 4.719,0.677 0.302,0.198 10 false B3 4.885,0.479 5.188,0.677 0.302,0.198 10 false B4 5.354,0.479 5.656,0.677 0.302,0.198 10 false F1 5.854,0.479 6.156,0.677 0.302,0.198 10 false F2 6.323,0.479 6.625,0.677 0.302,0.198 10 false F3 0.781,1.156 0.979,1.354 0.198,0.198 10 false R 0.781,1.49 0.979,1.688 0.198,0.198 10 false N 0.781,2.49 1.01,2.917 0.229,0.427 10 false D, S5 0.781,4.083 1.031,4.448 0.25,0.365 10 false S4 0.781,5.24 1.031,5.521 0.25,0.281 10 false S3 0.781,6.073 1.031,6.354 0.25,0.281 10 false S2 0.781,6.531 1.031,6.813 0.25,0.281 10 false S1 1.26,1.135 1.854,1.333 0.594,0.198 10 false Reverse 1.292,1.479 1.813,1.677 0.521,0.198 10 false Neutral 1.396,1.813 1.719,2.01 0.323,0.198 10 false 1st 1.385,2.156 1.792,2.354 0.406,0.198 10 false 2nd 1.406,2.49 1.74,2.688 0.333,0.198 10 false 3rd 1.396,2.823 1.677,3.021 0.281,0.198 10 false 4th 1.385,3.51 1.708,3.708 0.323,0.198 10 false 1st 1.385,3.844 1.792,4.042 0.406,0.198 10 false 2nd 1.406,4.177 1.74,4.375 0.333,0.198 10 false 3rd 1.385,4.854 1.708,5.052 0.323,0.198 10 false 1st 1.385,5.188 1.792,5.385 0.406,0.198 10 false 2nd 1.406,5.531 1.74,5.729 0.333,0.198 10 false 3rd 1.385,5.865 1.708,6.063 0.323,0.198 10 false 1st 1.385,6.542 1.708,6.74 0.323,0.198 10 false 1st 1.385,6.208 1.792,6.406 0.406,0.198 10 false 2nd 1.396,4.521 1.677,4.719 0.281,0.198 10 false 4th 1.396,3.167 1.677,3.365 0.281,0.198 10 false 5th 5.448,0.104 6.563,0.302 1.115,0.198 10 false One-way Clutch 4.083,0.115 4.563,0.313 0.479,0.198 10 false Brake 0.844,7.5 3.448,7.688 2.604,0.188 10 false ) : Operates during engine braking 0.917,6.885 1.948,7.073 1.031,0.188 10 false : Operates 0.917,7.198 4.521,7.385 3.604,0.188 10 false : Operates but is not related to power transmission 0.656,7.51 0.906,7.792 0.25,0.281 10 false (

X101987

Text in Illustration (1st Gear (D Position or S Mode):)
V100145

Operates

X101988

Text in Illustration (2nd Gear (D Position or S Mode):)
V100145

Operates

X101989

Text in Illustration (3rd Gear (D Position or S Mode):)
V100145

Operates

X101990

Text in Illustration (4th Gear (D Position or S Mode):)
V100145

Operates

X101991

Text in Illustration (5th Gear (D Position or S Mode):)
V100145

Operates

X101992

Text in Illustration (Reverse Gear (R Position):)
V100145

Operates



FAIL-SAFE


This function minimizes the loss of operability when an abnormality occurs in a sensor or solenoid. For details, refer to the Repair Manual.


DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the ECM illuminates or blinks the Malfunction Indicator Lamp (MIL) in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Code (DTC) of the malfunctions. The DTCs stored in the ECM are output to the Techstream via the ECM and the DLC3.


c.

A permanent DTC is used for the DTCs associated with the illumination of the MIL. Permanent DTCs cannot be cleared by using the Intelligent tester, disconnecting the battery terminal, or removing the EFI fuse.


d.

To clear other DTC that is stored in the ECM, use the Techstream, disconnect the cable from the battery terminal or remove the EFI fuse for 1 minute or longer.


e.

For details, refer to the Repair Manual.