Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2010.08–2013.08
NM1440E _54 Brake _056095 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0273716 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Combination Meter Assembly Brake System Warning Light
·

Lights up to alert the driver when the skid control ECU detects a malfunction in the EBD.

·

Lights up to alert the driver when the brake fluid level is low.

·

Lights up to alert the driver that the hydraulic pressure of the brake booster accumulator assembly in the hydraulic brake booster assembly has decreased.

·

Lights up to inform the driver of the parking brake condition.


ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Slip Indicator Light Blinks to inform the driver when the TRC, A-TRC, AUTO LSD, VSC and hill-start assist control is operational.
TRC OFF Indicator Light Lights up to inform the driver that the TRC OFF mode is entered using the VSC OFF switch.
VSC OFF Indicator Light Lights up to inform the driver that the VSC OFF mode is entered using the VSC OFF switch.
Downhill Assist Control Indicator Light Lights up to inform the driver when the downhill assist control switch turned on.
Buzzer Sounds intermittently to inform the driver that the hill-start assist control is active.
Front and Rear Speed Sensors Detects the wheel speed of each of the 4 wheels.
Yaw Rate Sensor Assembly
(Built-in Deceleration Sensor)
·

Detects the vehicle's longitudinal and lateral acceleration.

·

Detects the vehicle's yaw rate.


Steering Angle Sensor Detects the direction and angle of the steering wheel.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Assembly Detects that the parking brake lever is pulled up.
Center Differential Lock Detection Switch
(Built-into Transfer Shift Actuator Assembly)
Detects the center differential lock condition.
VSC OFF Switch Enables the driver to select the "Normal Mode", "TRC OFF Mode", or "VSC OFF Mode".
Downhill Assist Control Switch Turns the downhill assist control on and off.
Hydraulic Brake Booster Assembly Changes the brake fluid path based on the signals from the skid control ECU during the operations of the brake control functions in order to control the fluid pressure that is applied to the wheel cylinders.
Brake Fluid Level Warning Switch
(Built-into Hydraulic Brake Booster Assembly)
Detects the low brake fluid level.
Master Cylinder Pressure Sensor
(Built-into Hydraulic Brake Booster Assembly)
Detects the master cylinder pressure and outputs this signal to the skid control ECU.
Accumulator Pressure Sensor
(Built-into Hydraulic Brake Booster Assembly)
Monitors the hydraulic pressure of the brake booster accumulator assembly and outputs this signals for the brake booster pump assembly control.
Switching Solenoid Valve
(Built-into Hydraulic Brake Booster Assembly)
Switches the brake hydraulic path when the brake control system is activated.
Control Solenoid Valve
(Built-into Hydraulic Brake Booster Assembly)
Controls the hydraulic pressure that is applied to the wheel cylinders during brake control.
Brake Booster Pump Assembly
(Built-into Hydraulic Brake Booster Assembly)
Draws up the brake fluid from the brake master cylinder reservoir and provides high hydraulic pressure to the brake booster accumulator assembly.
Skid Control ECU Judges the vehicle driving condition based on signals from each sensor, and sends brake control signals to the hydraulic brake booster Assembly.
4WD Control ECU Sends the transfer drive mode.
ECM
·

Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU.

·

Based on the signals received from the skid control ECU, controls the engine output.




OPERATING CONDITION


a.

The brake control function vary by the transfer drive mode as shown in the following table:

2WD Models
Brake Control Function
ABS EBD Brake Assist TRC A-TRC AUTO LSD VSC Hill-start
Assist Control
Downhill
Assist Control
○ ○ ○ ○ X ○ ○ ○ X

4WD Models
Transfer
Drive Mode
Brake Control Function
ABS EBD Brake Assist TRC A-TRC AUTO LSD VSC Hill-start
Assist Control
Downhill
Assist Control
H4F ○ ○ ○ ○ X X ○ ○ X
H4L ○ ○ ○ ○ X X ○ ○ X
L4L ○ ○ ○ X ○ X X ○ ○

HINT:

○: Operates

X: Not operates



b.

Hill-start assist control

i.

The hill-start assist control operates when all of the following conditions have been met:

Hill-start Assist Control Operation Condition
·

The shift lever is in D or S.

·

The brake pedal is not depressed.

·

The rear differential lock switch is off.

·

The skid control ECU has detected the backward movement of the vehicle when the driver is starting off on a hill.




ii.

The hill-start assist control stops operating when any of the following conditions have been met:

Hill-start Assist Control Ending Condition
·

The shift lever is in any position other than D or S.

·

The brake pedal is depressed.

·

The rear differential lock switch is on.

·

Approximately 5 seconds have passed since control commenced.





c.

Downhill Assist Control

i.

The hill-start assist control operates when all of the following conditions have been met:

Downhill Assist Control Operation Condition
·

The downhill assist control switch is on

·

The transfer drive mode is in L4L.

·

The accelerator pedal and brake pedal is not depressed.

·

Descending a hill at a vehicle speed of 25 km/h (16 mph) or less.




ii.

The downhill assist control stops operating when any of the following conditions have been met:

Downhill Assist Control Ending Condition
·

The downhill assist control switch is off.

·

The transfer drive mode is in any position other than or L4L.

·

The accelerator pedal or brake pedal is depressed.






SYSTEM CONTROL


Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force distribution (EBD) The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior.
Brake Assist
·

The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance.

·

If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.


Traction Control (TRC) The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Active Traction Control (A-TRC) A-TRC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD effect.
AUTO LSD Briefly pressing the VSC OFF switch in normal mode enters TRC OFF mode, allowing the AUTO LSD to operate. The AUTO LSD achieves a function equivalent to that of an LSD system through the use of the TRC. The AUTO LSD applies brake hydraulic pressure to a slipping wheel to reduce the difference in rotation speed between the left and right drive wheels. This causes driving torque to be transmitted to the wheel opposite the slipping wheel.
Vehicle Stability Control (VSC) The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, such as may occur while cornering.
Hill-start Assist Control Hill-start assist control detects the backward descent of the vehicle and effects 4-wheel hydraulic pressure control to reduce the backward speed of the vehicle. As a result, the vehicle can be started off on a hill more easily.
Downhill Assist Control When the DAC switch is pressed with transfer drive mode in and L4L, and without accelerator and brake pedals operation, downhill assist control activates to effect 4-wheel hydraulic pressure control, in order to maintain a constant low vehicle speed without causing the wheels to become locked. Thus, the vehicle can descend a steep hill in a stable manner.

a.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X134262E01
1.635,1.01 2,1.271 0.365,0.26 10 false *A: 1.656,2.396 2.021,2.656 0.365,0.26 10 false *B: 4.51,1.073 4.875,1.333 0.365,0.26 10 false *a

Text in Illustration (The illustration provides a conceptual image)
*A Models with ABS *B Models without ABS
*a Brake Operation - -



b.

Electronic Brake Force Distribution (EBD)

i.

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.

X102063E01
5.052,0.563 6.958,0.865 1.906,0.302 10 false : EBD control 3.635,1.094 4.354,1.625 0.719,0.531 10 false Rear Brake Force 4.813,1.896 6.719,2.344 1.906,0.448 10 false Front Brake Force 5.052,0.188 6.958,0.49 1.906,0.302 10 false : Ideal brake force distribution 0.156,0.146 3.073,0.448 2.917,0.302 10 false EBD Control Concept (without Load in Rear)

X102064E01
5.052,0.542 6.958,0.844 1.906,0.302 10 false : EBD control 3.625,1.094 4.344,1.646 0.719,0.552 10 false Rear Brake Force 4.813,1.917 6.719,2.365 1.906,0.448 10 false Front Brake Force 5.052,0.177 6.958,0.479 1.906,0.302 10 false : Ideal brake force distribution 0.156,0.156 3.073,0.458 2.917,0.302 10 false EBD Control Concept (with Load in Rear)


ii.

During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.

X102065

Text in Illustration
V100136

Control Moment
V100135

Brake Force



c.

Brake Assist

i.

In the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the hydraulic brake booster assembly to increase the brake fluid pressure, which increases the brake force.

X104272E02
0.833,0.542 2.417,1.083 1.583,0.542 10 SKID CONTROL ECU 0.865,1.313 2.385,1.854 1.521,0.542 10 BRAKE ACTUATOR 0.875,3 3.698,3.667 2.823,0.667 10 Fluid Pressure Increased by Brake Actuator 4.115,0.698 4.521,1.198 0.406,0.5 10 Brake Force 5.115,1.26 6.448,1.833 1.333,0.573 10 With Brake Assist 4.948,2.073 6.458,2.583 1.51,0.51 10 Without Brake Assist 5.469,2.74 6.073,3.26 0.604,0.521 10 Time



d.

Traction Control (TRC)

i.

The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Simultaneously with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.

X102066E03
5.01,1.469 4.521,1.469 true 5.01,1.052 4.521,1.052 true 6.125,0.656 5.469,0.656 true 6.125,1.885 5.469,1.885 true 4.344,1.365 4.698,1.615 0.354,0.25 10 false *2 2.667,0.271 3.021,0.521 0.354,0.25 12 false *B: 1.063,0.271 1.417,0.521 0.354,0.25 12 false *A: 4.344,0.948 4.698,1.198 0.354,0.25 10 false *1 6.156,0.552 6.51,0.802 0.354,0.25 10 false *a 6.156,1.781 6.51,2.031 0.354,0.25 10 false *a

Text in Illustration (Driving Condition on Road with Different Surface Friction Characteristics)
*A Models without TRC *B Models with TRC
*1 ECM
- Engine Output Control
*2 Brake Actuator Assembly
- Hydraulic Brake Control
*a Brake Slipping Drive Wheel - -
V100145

Slippery Surface - -



e.

Active Traction Control (A-TRC)

i.

When the vehicle drive mode is L4L, the A-TRC helps restrain wheelspin by controlling the brake hydraulic pressure that is applied to the spinning wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an effect that is similar to Limited Slip Differential (LSD).


ii.

It independently controls the brake hydraulic pressure to the four wheels in accordance with the extent of the slippage at the wheels, as detected by the skid control ECU.

X104274E06
5.438,0.792 5.656,0.792 true 1.729,2.698 1.948,2.698 true 5.198,0.281 4.979,0.281 4.979,0.281 4.979,0.667 true 2.542,3.302 2.323,3.302 2.323,3.302 2.323,2.844 true 2.865,1.938 4.323,2.573 1.458,0.635 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 3.354,0.927 4.083,1.281 0.729,0.354 10 false ENGINE 5.708,0.688 6.958,1.042 1.25,0.354 10 false Slippery Surface 0.656,2.583 1.698,2.885 1.042,0.302 10 false Slippery Surface 4.76,2.875 5.875,3.229 1.115,0.354 10 false Traction 2.052,0.281 2.625,0.604 0.573,0.323 10 false Traction 0.198,0.156 1.448,0.51 1.25,0.354 12 false w/ A-TRC: 5.26,0.177 5.771,0.531 0.51,0.354 10 false Braking 2.604,3.198 3.115,3.552 0.51,0.354 10 false Braking

X102436E09
5.438,0.813 5.646,0.813 true 1.677,2.719 1.896,2.719 true 3.365,0.938 4.094,1.292 0.729,0.354 10 false ENGINE 5.708,0.708 6.958,1.063 1.25,0.354 10 false Slippery Surface 0.615,2.604 1.635,2.896 1.021,0.292 10 false Slippery Surface 5.156,2.219 6.271,2.573 1.115,0.354 10 false Not Traction 1.365,0.906 2.229,1.26 0.865,0.354 10 false Not Traction 0.115,0.104 1.365,0.458 1.25,0.354 12 false w/o A-TRC:



f.

AUTO LSD

i.

Briefly pressing the VSC OFF switch in normal mode allows the AUTO LSD to operate (TRC OFF mode is selected). The AUTO LSD achieves the LSD effect by regulating the hydraulic pressure that acts on the drive wheels.


ii.

TRC enhances the start-off performance of the vehicle during low-grip surface conditions, such as snow or mud, by restricting the acceleration effort during a start-off, in order to help prevent the wheels from spinning.


iii.

The AUTO LSD enhances the acceleration effort, in order to apply greater drive torque to the wheel that has grip. Thus, this function enables the vehicle to get unstuck if a wheel loses its grip, and enhances the vehicle's start-off performance when high-resistance surface conditions exist, such as loose gravel or sand.

X104275E08
4.958,2.563 5.177,2.563 true 4.76,0.458 4.542,0.458 4.542,0.458 4.542,0.813 true 4.781,3.125 4.563,3.125 4.563,3.125 4.563,2.656 true 2.354,1.823 3.823,2.552 1.469,0.729 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 1.656,1.469 2.427,2 0.771,0.531 10 false ENGINE 5.229,2.458 6.656,3 1.427,0.542 10 false Slippery Surface 4.813,0.354 5.635,0.885 0.823,0.531 10 false Traction 1.458,2.75 2.583,3.313 1.125,0.563 10 false Traction 0.208,0.115 1.604,0.771 1.396,0.656 12 false w/ AUTO LSD: 4.854,3.01 5.583,3.5 0.729,0.49 10 false Braking 2.875,3.042 4.188,3.542 1.313,0.5 10 false VSC OFF SWITCH

X104276E02
4.979,2.573 5.198,2.573 true 4.667,1.135 6.25,1.698 1.583,0.563 10 No Torque Transferred 1.646,1.469 2.521,2.052 0.875,0.583 10 ENGINE 5.281,2.479 6.688,3 1.406,0.521 10 Slippery Surface 4.302,2.823 5.042,3.365 0.74,0.542 10 Slipping 0.25,0.094 1.708,0.667 1.458,0.573 12 w/o AUTO LSD:



g.

Vehicle Stability Control (VSC)

i.

The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below:

X102067E01
4.698,2.302 5.052,2.563 0.354,0.26 10 false *b 2.177,2.302 2.531,2.563 0.354,0.26 10 false *a

Text in Illustration
*a Front Wheel Skid Tendency (Understeer)
- When the front wheels lose grip in relation to the rear wheel
*b Rear Wheel Skid Tendency (Oversteer)
- When the rear wheels lose grip in relation to the front wheels


ii.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle yaw rate, and vehicle's lateral acceleration, which are then calculated by the skid control ECU.


iii.

Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (a target yaw rate is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.

X102068E01
3.74,0.125 4.146,0.406 0.406,0.281 10 false *a 4.948,0.958 5.354,1.24 0.406,0.281 10 false *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on the Target Yaw Rate


iv.

Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X134263E01
3.51,0.063 3.719,0.302 0.208,0.24 10 false *a 3.958,0.135 4.167,0.375 0.208,0.24 10 false *b 4.229,0.49 4.438,0.729 0.208,0.24 10 false *c

Text in Illustration
*a Travel Direction of Vehicle's Center of Gravity *b Movement of Vehicle
*c Slip Angle - Slip Angle


v.

When the skid control ECU determines that the vehicle exhibits a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of the front or rear wheels to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the rear wheel on the inner circle of the turn in order to help restrain the front wheel skid tendency.

X102070

Text in Illustration (Front Wheel Skid Dampening at Right Turn)
V100136

Control Moment
V100135

Brake Force


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.

X102071

Text in Illustration
V100136

Control Moment
V100135

Brake Force



h.

Hill-start Assist Control

i.

When the vehicle starts off on a steep or slippery hill, the vehicle may descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, the hill-start assist control temporarily (approximately 5 seconds at the maximum) applies the brakes to the 4 wheels in order to prevent vehicle from descending backward.


ii.

Without the hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the hill-start assist control, however, the driver can start off easily and operate the pedal in a relaxed manner, because the hill-start assist control prevents the vehicle from descending backward.

X102437E03
4.156,3.354 6.406,3.802 2.25,0.448 10 w/o Hill-start Assist Control 4.604,2.927 7.063,3.406 2.458,0.479 10 Increases backward speed of vehicle 1.188,3.323 3.26,3.802 2.073,0.479 10 w/ Hill-start Assist Control 5.344,0.198 6.771,0.594 1.427,0.396 10 Difficult Control 2.208,0.24 3.635,0.635 1.427,0.396 10 Easy Control 1.073,2.917 3.5,3.375 2.427,0.458 10 Reduce backward speed of vehicle



i.

Downhill Assist Control

i.

When the vehicle is descending a steep hill and the engine brake alone cannot provide a sufficient deceleration force while the transfer drive mode is in or L4L, downhill assist control effects 4 wheels brake control to maintain a constant, low vehicle speed. Thus, the vehicle is able to descend in a stable manner without causing the wheels to become locked.


ii.

When the vehicle descends a steep hill without downhill assist control, the driver must pay close attention to the brake and accelerator pedal maneuvers. However, with downhill assist control, the driver can concentrate on the steering operation, without accelerator and brake pedals operation.


iii.

Downhill assist control enables the vehicle to maintain stability because it can descend a slippery hill at low speeds without causing the wheels to become locked.

X102438E07
4.469,4.344 6.615,4.813 2.146,0.469 10 false w/o Downhill Assist Control 3.219,0.323 4.417,0.823 1.198,0.5 10 false Difficult Control 0.438,0.313 1.604,0.76 1.167,0.448 10 false Easy Control 0.271,1.521 1.25,2.219 0.979,0.698 10 false No Braking and No Acclerating 0.927,3.594 2.135,3.979 1.208,0.385 10 false Stable Speed 3.792,3.958 5.094,4.365 1.302,0.406 10 false Unstable Speed 1.073,4.333 2.813,4.76 1.74,0.427 10 false w/ Downhill Assist Control




FUNCTION


a.

VSC OFF Switch

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.

X104392E02
3.219,2.958 3.219,2.354 true 3.271,3.115 3.271,3.417 3.271,3.417 3.031,3.417 true 3.146,2.156 3.302,2.333 0.156,0.177 10 false *1 2.833,3.313 2.99,3.458 0.156,0.146 10 false *2 4.729,3.281 4.885,3.458 0.156,0.177 10 false *3

Text in Illustration
*1 TRC OFF Indicator Light *2 VSC OFF Indicator Light
*3 VSC OFF Switch - -


ii.

The VSC OFF switch can select 3 modes (mode A, mode B, and mode C).


iii.

Briefly pressing the VSC OFF switch in mode A selects the mode B.


iv.

Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the mode C.


v.

Briefly pressing the VSC OFF switch in the mode B or mode C or turning the ignition switch off returns to the mode A.


vi.

When TRC is not operating, the TRC OFF indicator light will illuminate.


vii.

When VSC is not operating, the VSC OFF indicator light will illuminate.

X102072E01
4.583,0.75 6.406,1.729 1.823,0.979 10 false : VSC OFF switch operation (press and hold for 3 seconds or more) 4.583,0.24 7.052,0.625 2.469,0.385 10 false : VSC OFF switch operation (briefly) 0.844,1.74 1.688,2.104 0.844,0.365 10 false Mode C 2.229,0.573 3.094,0.938 0.865,0.365 10 false Mode A 3.604,1.74 4.448,2.104 0.844,0.365 10 false Mode B

Function of VSC OFF Switch
Transfer Drive Mode Brake Control Function VSC OFF Switch Mode
Mode A Mode B Mode C
H4F TRC Operates Not Operates Not Operates
A-TRC Not Operates Not Operates Not Operates
VSC Operates Operates Not Operates
H4L TRC Operates Not Operates Not Operates
A-TRC Not Operates Not Operates Not Operates
VSC Operates Operates Not Operates
L4L TRC Not Operates - Not Operates
A-TRC Operates - Not Operates
VSC Not Operates - Not Operates




CONSTRUCTION


a.

Yaw Rate Sensor Assembly

i.

This sensor has a built-in deceleration sensor.


ii.

The yaw rate sensor detects the vehicle's yaw rate.


iii.

The deceleration sensor detects the vehicle's longitudinal and lateral acceleration

X102074E01
4.948,1.208 5.25,0.719 true 4.521,1.375 4.188,0.708 true 1.385,1.958 1.771,2.25 0.385,0.292 10 false *1 5.01,1.74 5.396,2.031 0.385,0.292 10 false *a 5.219,0.521 5.604,0.813 0.385,0.292 10 false *3 4.073,0.51 4.458,0.802 0.385,0.292 10 false *2

Text in Illustration
*1 Yaw Rate Sensor Assembly *2 Yaw Rate Sensor
*3 Deceleration Sensor - -
*a Cross Section - -



b.

Steering Angle Sensor

i.

The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.

X102075



c.

Speed Sensor

i.

Active type speed sensors, which can detect the rotational direction of the wheel, have been provided. This sensor contains a Hall IC, which consists of 2 Magnetic Resistance Elements (MREs).


ii.

The magnet type rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.

X102443E04
1.917,0.917 2.5,0.917 true 1.958,3.208 2.542,3.208 true 5.115,1.563 5.698,1.563 true 5.125,3.656 5.708,3.656 true 2.542,0.813 2.698,0.99 0.156,0.177 10 false *1 2.583,3.104 2.74,3.281 0.156,0.177 10 false *3 1.719,2.281 1.875,2.458 0.156,0.177 10 false *a 1.75,4.49 1.906,4.667 0.156,0.177 10 false *b 5.74,1.458 5.896,1.635 0.156,0.177 10 false *2 5.76,3.552 5.917,3.729 0.156,0.177 10 false *2

Text in Illustration
*1 Front Speed Sensor *2 Sensor Rotor
*3 Rear Speed Sensor - -
*a Front Axle *b Rear Axle



d.

Hydraulic Brake Booster Assembly

i.

The brake actuator portion in hydraulic brake booster consists of 4 switching solenoid valves, 8 control solenoid valves and skid control ECU.


ii.

The pressure increase mode, the pressure holding mode, and the pressure reduction mode are effected based on the combination of these solenoid valves that are turned on and off, in order to control the hydraulic pressure that is applied to each of the wheel cylinders.


iii.

4 switching solenoid valves are used: 2 (SMCF, SREA) in the front brake fluid path, 1 (SREC) in the rear brake fluid path, and 1 (STR) in the accumulator fluid path. The switching solenoid valves open and closed in accordance with the control signals from the skid control ECU in order to switch the respective brake fluid path.


iv.

8 control solenoid valves are used for the 4 wheels (2 types per wheel: pressure holding solenoid and pressure reduction solenoid).

X102444

X102445E03
3.771,2.188 3.49,2.188 true 4.677,5.094 5.063,5.365 0.385,0.271 10 false *d 4.104,5.094 4.49,5.365 0.385,0.271 10 false *c 2.677,5.094 3.063,5.365 0.385,0.271 10 false *b 5.188,4.125 5.573,4.396 0.385,0.271 10 false *13 4.188,4.125 4.573,4.396 0.385,0.271 10 false *12 3.198,4.125 3.583,4.396 0.385,0.271 10 false *11 5.24,3.167 5.625,3.438 0.385,0.271 10 false *9 4.25,3.167 4.635,3.438 0.385,0.271 10 false *8 3.25,3.167 3.635,3.438 0.385,0.271 10 false *7 4.719,1.708 5.104,1.979 0.385,0.271 10 false *4 3.792,1.708 4.177,1.979 0.385,0.271 10 false *3 2.885,1.708 3.271,1.979 0.385,0.271 10 false *2 1.979,1.708 2.365,1.979 0.385,0.271 10 false *1 3.813,2.083 4.198,2.354 0.385,0.271 10 false *5 2.26,3.167 2.646,3.438 0.385,0.271 10 false *6 2.208,4.125 2.594,4.396 0.385,0.271 10 false *10 2.104,5.094 2.49,5.365 0.385,0.271 10 false *a

Text in Illustration
*1 STR (Traction Solenoid Valve) *2 SREC (Regulator Cut Solenoid Valve)
*3 SREA
(Regulator Apply for Front Solenoid Valve)
*4 SMCF (Master Cut for Front Solenoid Valve)
*5 Master Cylinder Pressure Sensor *6 SH (Pressure Holding Solenoid Valve)
*7 SH (Pressure Holding Solenoid Valve) *8 SH (Pressure Holding Solenoid Valve)
*9 SH (Pressure Holding Solenoid Valve) *10 SR (Pressure Holding Solenoid Valve)
*11 SR (Pressure Holding Solenoid Valve) *12 SR (Pressure Holding Solenoid Valve)
*13 SR (Pressure Holding Solenoid Valve) - -
*a Rear LH *b Rear RH
*c Front LH *d Front RH
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder - -




OPERATION


a.

Speed Sensor

i.

The active type speed sensor uses a Hall IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.

X102078E07
6.531,2.792 7,3.167 0.469,0.375 10 false Time 3.75,2.198 4.271,3.125 0.521,0.927 10 false Output Voltage 4.688,2.896 6.406,3.333 1.719,0.438 10 false Digital Pulse (Backward) 2.49,1.406 2.979,1.813 0.49,0.406 10 false Hall IC 4.688,1.219 6.344,1.583 1.656,0.365 10 false Digital Pulse (Forward) 3.75,0.5 4.25,1.448 0.5,0.948 10 false Output Voltage 6.521,1.104 6.958,1.448 0.438,0.344 10 false Time 0.51,2.167 1.896,3.115 1.385,0.948 10 false Sensor Rotor (Bearing Inner Race) 1.781,1.302 2.302,1.594 0.521,0.292 10 false MRE A 1.792,1.583 2.302,1.865 0.51,0.281 10 false MRE B


ii.

To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by the 2 Magnetic Resistance Elements (MREs).


iii.

Upon receiving this signal, the Hall IC outputs a forward or backward wave.

X102079E01
2.771,2.146 3.76,2.531 0.99,0.385 10 false MRE B: Lo 0.167,0.156 1.198,0.552 1.031,0.396 10 false Forward 2.771,1.771 3.76,2.156 0.99,0.385 10 false MRE A: Hi 1.906,1.563 2.406,1.917 0.5,0.354 10 false MRE B 1.906,1.198 2.406,1.531 0.5,0.333 10 false MRE A

X102080E01
3.302,2.146 4.292,2.531 0.99,0.385 10 false MRE B: Hi 0.167,0.177 1.198,0.573 1.031,0.396 10 false Backward 3.302,1.781 4.292,2.167 0.99,0.385 10 false MRE A: Hi 1.906,1.563 2.396,1.906 0.49,0.344 10 false MRE B 1.906,1.208 2.396,1.51 0.49,0.302 10 false MRE A


iv.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.

X102081E01
1.417,1.802 2.448,2.188 1.031,0.385 10 false Sensor Output 1.417,0.635 2.438,0.99 1.021,0.354 10 false Vehicle Speed



b.

ABS and EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks wheel slipping conditions.


ii.

The skid control ECU compares the speed sensor signals of the front and rear, judges the slipping condition of the rear wheel, and operates the EBD.


iii.

When a wheel is about to lock, the ABS operation starts in order to regulate the hydraulic pressure at the wheel cylinders while switching between the 3 modes: pressure increase, pressure holding, and pressure reduction.

X104273E04
4.635,1.969 6.865,2.448 2.229,0.479 10 false SWITCHING SOLENOID VALVE 4.677,2.479 6.854,2.948 2.177,0.469 10 false CONTROL SOLENOID VALVE 4.75,1.177 6.625,1.854 1.875,0.677 10 false ACCUMULATOR PRESSURE SENSOR 4.969,0.344 6.365,1.052 1.396,0.708 10 false MASTER CYLINDER PRESSURE SENSOR 4.854,3.021 6.51,3.708 1.656,0.688 10 false BRAKE BOOSTER PUMP ASSEMBLY 3.25,1.865 3.927,2.844 0.677,0.979 10 false SKID CONTROL ECU 0.531,2.438 2.021,3.125 1.49,0.688 10 false COMBINATION METER ASSEMBLY 0.771,3.208 1.875,4.031 1.104,0.823 10 false BRAKE SYSTEM WARNING LIGHT 0.667,3.979 2.344,4.49 1.677,0.51 10 false ABS WARNING LIGHT 0.74,0.375 2.177,0.885 1.438,0.51 10 false SPEED SENSOR 0.271,0.875 2.635,1.365 2.365,0.49 10 false STOP LIGHT SWITCH ASSEMBLY 1.927,1.917 2.792,2.26 0.865,0.344 10 false CAN (V bus) 0.281,1.5 2.656,1.917 2.375,0.417 10 false YAW RATE SENSOR ASSEMBLY 3.479,4.052 6.615,4.583 3.135,0.531 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY

X102447E03
5.417,3.125 5.729,3.01 true 4.427,3.094 4.646,2.833 true 3.448,3.104 3.656,2.802 true 1.771,3.24 2.083,3.115 true 4.604,4.396 4.906,4.625 0.302,0.229 10 false *d 4.042,4.396 4.344,4.625 0.302,0.229 10 false *c 2.625,4.396 2.927,4.625 0.302,0.229 10 false *b 5.49,2.188 5.792,2.417 0.302,0.229 10 false *8 4.51,2.188 4.813,2.427 0.302,0.24 10 false *7 3.521,2.188 3.823,2.417 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.823,1.385 3.125,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.188 2.823,2.417 0.302,0.229 10 false *5 5.74,2.865 6.042,3.094 0.302,0.229 10 false *12 4.563,2.635 4.865,2.865 0.302,0.229 10 false *11 3.573,2.604 3.875,2.833 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.396 2.354,4.625 0.302,0.229 10 false *a

EBD Operation
Item EBD Not Activated EBD Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) ← ← ←
*2 SREC Off (Open) ← ← ←
*3 SREA Off (Closed) ← ← ←
*4 SMCF Off (Open) ← ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← ←
*d Wheel Cylinder Pressure - - - -
Rear Brake LH *5 SH Off (Open) On (Closed) ← ←
*9 SR Off (Closed) ← ← ←
*a Wheel Cylinder Pressure - - - -
Rear Brake RH *6 SH Off (Open) On (Closed) ← ←
*10 SR Off (Closed) ← ← ←
*b Wheel Cylinder Pressure - - - -
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder

X102448E05
5.573,3.25 5.885,3.125 true 4.573,3.219 4.792,2.958 true 3.594,3.24 3.802,2.948 true 1.917,3.365 2.229,3.24 true 4.76,4.521 5.063,4.75 0.302,0.229 10 false *d 4.198,4.521 4.5,4.75 0.302,0.229 10 false *c 2.771,4.521 3.073,4.75 0.302,0.229 10 false *b 5.646,2.302 5.948,2.531 0.302,0.229 10 false *8 4.656,2.302 4.958,2.531 0.302,0.229 10 false *7 3.667,2.302 3.969,2.531 0.302,0.229 10 false *6 4.781,1.521 5.083,1.75 0.302,0.229 10 false *4 3.885,1.521 4.188,1.75 0.302,0.229 10 false *3 2.969,1.521 3.271,1.75 0.302,0.229 10 false *2 2.042,1.521 2.344,1.75 0.302,0.229 10 false *1 2.677,2.302 2.979,2.531 0.302,0.229 10 false *5 5.896,2.969 6.198,3.198 0.302,0.229 10 false *12 4.75,2.771 5.052,3 0.302,0.229 10 false *11 3.75,2.76 4.052,2.99 0.302,0.229 10 false *10 1.75,3.271 2.052,3.5 0.302,0.229 10 false *9 2.198,4.521 2.5,4.75 0.302,0.229 10 false *a

ABS Operation
Item ABS Not Activated ABS Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) ← ← ←
*2 SREC Off (Open) ← ← ←
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← Off (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder

HINT:

While the front wheels are in the ABS operation, SREA and SMCF are on. While only rear wheels are in the ABS operation, SREA and SMCF are off.




c.

Brake Assist

i.

If an emergency braking situation has occurred, it is detected by the skid control ECU based on the vehicle speed signal from the speed sensor, the brake pedal application speed from the master cylinder pressure sensor, and the signal representing the amount of pedal effort. Then, the skid control ECU actuates each solenoid valve. As a result, the pressure from the brake booster accumulator assembly is applied to the wheel cylinders. The accumulator pressure that is applied to the wheel cylinders generates a higher pressure than the master cylinder.

X104278E05
1.24,3.656 1.823,4.208 0.583,0.552 10 false ECM 0.792,0.427 2.542,1.083 1.75,0.656 10 false SPEED SENSOR 0.281,0.938 2.781,1.563 2.5,0.625 10 false STOP LIGHT SWITCH ASSEMBLY 4.917,0.354 6.323,1.125 1.406,0.771 10 false MASTER CYLINDER PRESSURE SENSOR 4.906,1.177 6.323,1.823 1.417,0.646 10 false ACCUMULATOR PRESSURE SENSOR 4.625,2 7.083,2.521 2.458,0.521 10 false SWITCHING SOLENOID VALVE 4.646,2.5 7.094,3.083 2.448,0.583 10 false CONTROL SOLENOID VALVE 4.906,3.031 6.135,3.75 1.229,0.719 10 false BRAKE BOOSTER PUMP ASSEMBLY 3.229,1.677 4.01,2.656 0.781,0.979 10 false SKID CONTROL ECU 0.76,2.344 1.885,3.021 1.125,0.677 10 false BRAKE SYSTEM WARNING LIGHT 0.635,3.094 2.354,3.656 1.719,0.563 10 false ABS WARNING LIGHT 0.625,1.542 2.115,2.448 1.49,0.906 10 false COMBINATION METER ASSEMBLY 2.542,3.948 3,4.521 0.458,0.573 10 false CAN (V bus) 3.542,4.104 6.688,4.698 3.146,0.594 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY

X102461E10
5.438,3.094 5.75,2.979 true 4.427,3.073 4.646,2.813 true 3.448,3.083 3.656,2.781 true 1.771,3.24 2.083,3.115 true 4.604,4.396 4.906,4.625 0.302,0.229 10 false *d 4.042,4.396 4.344,4.625 0.302,0.229 10 false *c 2.625,4.396 2.927,4.625 0.302,0.229 10 false *b 5.49,2.188 5.792,2.417 0.302,0.229 10 false *8 4.51,2.188 4.813,2.417 0.302,0.229 10 false *7 3.521,2.188 3.823,2.417 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.74,1.385 3.042,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.188 2.823,2.417 0.302,0.229 10 false *5 5.76,2.854 6.063,3.083 0.302,0.229 10 false *12 4.573,2.625 4.875,2.854 0.302,0.229 10 false *11 3.573,2.583 3.875,2.813 0.302,0.229 10 false *10 1.604,3.146 1.906,3.375 0.302,0.229 10 false *9 2.052,4.396 2.354,4.625 0.302,0.229 10 false *a

Brake Assist Operation
Item Brake Assist Not Activated Brake Assist Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



d.

TRC

i.

The fluid pressure that is generated by the brake booster pump assembly is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the pressure to the wheel cylinders of the drive wheels is controlled in the following 3 modes: increase mode, holding mode, and reduction mode, to restrain the slippage of the drive wheels.


ii.

The skid control ECU outputs a TRC operation signal to the ECM. Upon receiving this signal, the ECM effects engine output control.


iii.

If the accumulator pressure drops during this operation, the skid control ECU receives the signals from the accumulator pressure sensor and actuates the brake booster pump assembly to ensure the proper accumulator pressure.

X104284E03
0.333,1.052 2.344,1.667 2.01,0.615 10 false CENTER DIFFERENTIAL LOCK DETECTION SWITCH 4.594,2.104 6.771,2.448 2.177,0.344 10 false SWITCHING SOLENOID VALVE 4.646,2.604 6.719,2.938 2.073,0.333 10 false CONTROL SOLENOID VALVE 3.219,1.656 3.906,2.594 0.688,0.938 10 false SKID CONTROL ECU 0.49,3.281 2,3.917 1.51,0.635 10 false COMBINATION METER ASSEMBLY 0.76,2.146 1.99,2.469 1.229,0.323 10 false VSC OFF SWITCH 4.729,1.281 6.594,1.844 1.865,0.563 10 false ACCUMULATOR PRESSURE SENSOR 4.948,0.469 6.344,1.115 1.396,0.646 10 false MASTER CYLINDER PRESSURE SENSOR 4.823,3.156 6.469,3.781 1.646,0.625 10 false BRAKE BOOSTER PUMP ASSEMBLY 4.917,5.01 6.354,5.406 1.438,0.396 10 false 4WD CONTROL ECU 4.427,5.583 6.688,5.979 2.26,0.396 10 false YAW RATE SENSOR ASSEMBLY 5.333,4.51 6.563,4.906 1.229,0.396 10 false ECM 3,5.854 3.896,6.198 0.896,0.344 10 false CAN (V bus) 0.594,4.031 2.177,4.365 1.583,0.333 10 false SLIP INDICATOR LIGHT 0.396,4.406 2.365,4.75 1.969,0.344 10 false TRC OFF INDICATOR LIGHT 0.771,0.344 2.073,0.667 1.302,0.323 10 false SPEED SENSOR 3.542,4.125 6.552,4.49 3.01,0.365 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY

X102461E10
5.438,3.094 5.75,2.979 true 4.427,3.073 4.646,2.813 true 3.448,3.083 3.656,2.781 true 1.771,3.24 2.083,3.115 true 4.604,4.396 4.906,4.625 0.302,0.229 10 false *d 4.042,4.396 4.344,4.625 0.302,0.229 10 false *c 2.625,4.396 2.927,4.625 0.302,0.229 10 false *b 5.49,2.188 5.792,2.417 0.302,0.229 10 false *8 4.51,2.188 4.813,2.417 0.302,0.229 10 false *7 3.521,2.188 3.823,2.417 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.74,1.385 3.042,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.188 2.823,2.417 0.302,0.229 10 false *5 5.76,2.854 6.063,3.083 0.302,0.229 10 false *12 4.573,2.625 4.875,2.854 0.302,0.229 10 false *11 3.573,2.583 3.875,2.813 0.302,0.229 10 false *10 1.604,3.146 1.906,3.375 0.302,0.229 10 false *9 2.052,4.396 2.354,4.625 0.302,0.229 10 false *a

TRC Operation
Item TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



e.

A-TRC

i.

Based on the vehicle speed that has been calculated from each speed sensor and the signals of the yaw rate and deceleration sensor, the skid control ECU computes the target control speed.


ii.

The skid control ECU compares the target control speed and the wheel speed to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valve of the hydraulic brake booster assembly to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.

X104285E02
4.542,6.26 6.531,6.656 1.99,0.396 10 false STEERING ANGLE SENSOR 4.917,5.135 6.354,5.531 1.438,0.396 10 false 4WD CONTROL ECU 4.406,5.646 6.667,6.042 2.26,0.396 10 false YAW RATE SENSOR ASSEMBLY 5.333,4.625 6.563,5.021 1.229,0.396 10 false ECM 0.344,1.292 2.354,1.927 2.01,0.635 10 false CENTER DIFFERENTIAL LOCK DETECTION SWITCH 4.594,2.229 6.771,2.573 2.177,0.344 10 false SWITCHING SOLENOID VALVE 4.646,2.74 6.719,3.073 2.073,0.333 10 false CONTROL SOLENOID VALVE 2.958,5.906 3.938,6.219 0.979,0.313 10 false CAN (V bus) 1.083,5.24 1.729,5.604 0.646,0.365 10 false BUZZER 3.229,1.771 3.906,2.729 0.677,0.958 10 false SKID CONTROL ECU 0.51,3.74 2.01,4.354 1.5,0.615 10 false COMBINATION METER ASSEMBLY 0.594,4.49 2.177,4.823 1.583,0.333 10 false SLIP INDICATOR LIGHT 0.542,4.865 2.271,5.198 1.729,0.333 10 false A-TRC INDICATOR LIGHT 0.771,0.479 2.073,0.802 1.302,0.323 10 false SPEED SENSOR 0.281,2.573 2.51,2.896 2.229,0.323 10 false STOP LIGHT SWITCH ASSEMBLY 3.698,4.24 6.583,4.604 2.885,0.365 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 4.729,1.417 6.594,1.958 1.865,0.542 10 false ACCUMULATOR PRESSURE SENSOR 4.948,0.594 6.344,1.208 1.396,0.615 10 false MASTER CYLINDER PRESSURE SENSOR 4.813,3.281 6.458,3.917 1.646,0.635 10 false BRAKE BOOSTER PUMP ASSEMBLY


iii.

The fluid pressure control of the A-TRC independently controls the brake of each wheel by operating the individual solenoid valves in accordance with the signals received from the skid control ECU. The brake of each wheel is controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.

X102461E10
5.438,3.094 5.75,2.979 true 4.427,3.073 4.646,2.813 true 3.448,3.083 3.656,2.781 true 1.771,3.24 2.083,3.115 true 4.604,4.396 4.906,4.625 0.302,0.229 10 false *d 4.042,4.396 4.344,4.625 0.302,0.229 10 false *c 2.625,4.396 2.927,4.625 0.302,0.229 10 false *b 5.49,2.188 5.792,2.417 0.302,0.229 10 false *8 4.51,2.188 4.813,2.417 0.302,0.229 10 false *7 3.521,2.188 3.823,2.417 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.74,1.385 3.042,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.188 2.823,2.417 0.302,0.229 10 false *5 5.76,2.854 6.063,3.083 0.302,0.229 10 false *12 4.573,2.625 4.875,2.854 0.302,0.229 10 false *11 3.573,2.583 3.875,2.813 0.302,0.229 10 false *10 1.604,3.146 1.906,3.375 0.302,0.229 10 false *9 2.052,4.396 2.354,4.625 0.302,0.229 10 false *a

A-TRC Operation
Item A-TRC Not Activated A-TRC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



f.

AUTO LSD

i.

AUTO LSD is a function that has effects similar to a mechanical type LSD. AUTO LSD employs the TRC to control brake hydraulic pressure and engine output.


ii.

The Skid Control ECU detects slippage that occurs as a result of a rotational difference between the drive wheel and the non-driven wheel. Via the TRC, the AUTO LSD detects the wheel slip that occurs (the wheel that is rotating faster) , based on the rotational difference of the right and left drive wheels, and puts AUTO LSD into action.

X104280E03
4.417,5.615 6.833,6.281 2.417,0.667 10 false YAW RATE SENSOR ASSEMBLY 5.198,4.76 6.427,5.156 1.229,0.396 10 false ECM 0.323,1.292 2.302,2.021 1.979,0.729 10 false CENTER DIFFERENTIAL LOCK DETECTION SWITCH 4.594,2.125 7.042,2.781 2.448,0.656 10 false SWITCHING SOLENOID VALVE 4.646,2.615 6.948,3.219 2.302,0.604 10 false CONTROL SOLENOID VALVE 2.948,5.896 4.125,6.542 1.177,0.646 10 false CAN (V bus) 3.24,1.781 3.927,2.771 0.688,0.99 10 false SKID CONTROL ECU 0.615,3.635 2.125,4.396 1.51,0.76 10 false COMBINATION METER ASSEMBLY 0.583,4.344 2.427,4.979 1.844,0.635 10 false SLIP INDICATOR LIGHT 0.396,4.74 2.688,5.458 2.292,0.719 10 false AUTO LSD INDICATOR LIGHT 0.781,0.542 2.229,1.156 1.448,0.615 10 false SPEED SENSOR 0.781,2.469 2.323,3.042 1.542,0.573 10 false VSC OFF SWITCH 3.698,4.167 6.771,4.792 3.073,0.625 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 4.75,1.292 6.635,2.083 1.885,0.792 10 false ACCUMULATOR PRESSURE SENSOR 4.948,0.49 6.354,1.281 1.406,0.792 10 false MASTER CYLINDER PRESSURE SENSOR 4.813,3.167 6.469,3.938 1.656,0.771 10 false BRAKE BOOSTER PUMP ASSEMBLY

X103121E02
5.552,3.25 5.865,3.135 true 4.573,3.25 4.781,3 true 3.583,3.24 3.792,2.938 true 1.938,3.385 2.25,3.271 true 4.771,4.531 5.073,4.76 0.302,0.229 10 false *d 4.208,4.531 4.51,4.76 0.302,0.229 10 false *c 2.781,4.531 3.083,4.76 0.302,0.229 10 false *b 5.656,2.281 5.958,2.51 0.302,0.229 10 false *8 4.667,2.281 4.969,2.51 0.302,0.229 10 false *7 3.677,2.281 3.979,2.51 0.302,0.229 10 false *6 4.802,1.531 5.104,1.76 0.302,0.229 10 false *4 3.896,1.531 4.198,1.76 0.302,0.229 10 false *3 2.979,1.531 3.281,1.76 0.302,0.229 10 false *2 2.073,1.531 2.375,1.76 0.302,0.229 10 false *1 2.688,2.281 2.99,2.51 0.302,0.229 10 false *5 5.875,2.969 6.177,3.198 0.302,0.229 10 false *12 4.74,2.823 5.042,3.052 0.302,0.229 10 false *11 3.75,2.76 4.052,2.99 0.302,0.229 10 false *10 1.781,3.292 2.083,3.521 0.302,0.229 10 false *9 2.219,4.531 2.521,4.76 0.302,0.229 10 false *a

AUTO LSD Operation
Item AUTO LSD
Not Activated
AUTO LSD Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Open) On (Closed) ← ←
*2 SREC Off (Closed) On (Open) ← ←
*3 SREA Off (Closed) ← ← ←
*4 SMCF Off (Open) ← ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← ← ←
*11 SR Off (Closed) ← ← ←
*c Wheel Cylinder Pressure - - - -
Front Brake RH *8 SH Off (Open) ← ← ←
*12 SR Off (Closed) ← ← ←
*e Wheel Cylinder Pressure - - - -
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



g.

VSC

i.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the vehicle's yaw moment. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency of the front wheels or the rear wheels to skid is restrained.


ii.

At this time, the skid control ECU outputs a VSC operation signal to the ECM and the combination meter assembly. Upon receiving this signal, the ECM controls the engine output. The slip indicator light will blink in the combination meter assembly.

X104286E02
4.552,6.656 6.521,6.99 1.969,0.333 10 false STEERING ANGLE SENSOR 4.813,5.656 6.25,5.979 1.438,0.323 10 false 4WD CONTROL ECU 4.438,6.146 6.625,6.5 2.188,0.354 10 false YAW RATE SENSOR ASSEMBLY 5.344,5.146 5.729,5.448 0.385,0.302 10 false ECM 4.583,2.01 6.76,2.354 2.177,0.344 10 false SWITCHING SOLENOID VALVE 4.635,2.5 6.708,2.833 2.073,0.333 10 false CONTROL SOLENOID VALVE 1.885,6.052 2.708,6.396 0.823,0.344 10 false CAN (V bus) 3.219,2 3.896,2.99 0.677,0.99 10 false SKID CONTROL ECU 0.771,0.354 2.073,0.677 1.302,0.323 10 false SPEED SENSOR 0.281,1.01 2.51,1.333 2.229,0.323 10 false STOP LIGHT SWITCH ASSEMBLY 3.698,4.74 6.583,5.104 2.885,0.365 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 4.719,1.177 6.594,1.729 1.875,0.552 10 false ACCUMULATOR PRESSURE SENSOR 4.938,0.365 6.333,0.99 1.396,0.625 10 false MASTER CYLINDER PRESSURE SENSOR 4.802,3.042 6.458,3.677 1.656,0.635 10 false BRAKE BOOSTER PUMP ASSEMBLY 0.604,3.938 2.104,4.563 1.5,0.625 10 false COMBINATION METER ASSEMBLY 0.563,4.698 2.146,5.031 1.583,0.333 10 false SLIP INDICATOR LIGHT 0.438,5.073 2.323,5.417 1.885,0.344 10 false VSC OFF INDICATOR LIGHT 0.813,2.906 2.313,3.313 1.5,0.406 10 false VSC OFF SWITCH 0.333,1.708 2.323,2.354 1.99,0.646 10 false CENTER DIFFERENTIAL LOCK DETECTION SWITCH


iii.

During front wheel skid restraining control, the brakes of the rear wheels and front wheel of the outer side of the turn are applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a front wheel skid while the vehicle is making a right turn.

X102458E03
5.417,3.104 5.729,2.99 true 4.406,3.094 4.625,2.833 true 3.427,3.125 3.635,2.823 true 1.771,3.24 2.083,3.115 true 4.604,4.385 4.906,4.615 0.302,0.229 10 false *d 4.042,4.385 4.344,4.615 0.302,0.229 10 false *c 2.625,4.385 2.927,4.615 0.302,0.229 10 false *b 5.49,2.177 5.792,2.406 0.302,0.229 10 false *8 4.51,2.177 4.833,2.406 0.323,0.229 10 false *7 3.521,2.177 3.823,2.406 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.74,1.385 3.042,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.177 2.823,2.406 0.302,0.229 10 false *5 5.75,2.854 6.052,3.083 0.302,0.229 10 false *12 4.604,2.646 4.906,2.875 0.302,0.229 10 false *11 3.594,2.635 3.896,2.865 0.302,0.229 10 false *10 1.604,3.146 1.906,3.375 0.302,0.229 10 false *9 2.052,4.385 2.354,4.615 0.302,0.229 10 false *a

VSC Operation (Turning Right)
Item VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) On (Closed) ← ←
*12 SR Off (Closed) ← ← ←
*d Wheel Cylinder Pressure - - - -
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder


iv.

During rear wheel skid restraining control, the front wheel brake of the outer side of the turn is applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which the brake might be applied to the rear brake of the outer side of the turn. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a rear wheel skid while the vehicle is making a right turn.

X102459E03
5.406,3.094 5.719,2.979 true 4.406,3.083 4.625,2.823 true 3.427,3.115 3.635,2.813 true 1.76,3.25 2.073,3.125 true 4.604,4.385 4.906,4.615 0.302,0.229 10 false *d 4.042,4.385 4.344,4.615 0.302,0.229 10 false *c 2.625,4.385 2.927,4.615 0.302,0.229 10 false *b 5.49,2.177 5.792,2.406 0.302,0.229 10 false *8 4.51,2.177 4.813,2.406 0.302,0.229 10 false *7 3.521,2.177 3.823,2.406 0.302,0.229 10 false *6 4.635,1.375 4.938,1.604 0.302,0.229 10 false *4 3.74,1.375 4.042,1.604 0.302,0.229 10 false *3 2.74,1.375 3.042,1.604 0.302,0.229 10 false *2 1.906,1.375 2.208,1.604 0.302,0.229 10 false *1 2.521,2.177 2.823,2.406 0.302,0.229 10 false *5 5.74,2.844 6.042,3.073 0.302,0.229 10 false *12 4.563,2.635 4.865,2.865 0.302,0.229 10 false *11 3.583,2.625 3.885,2.854 0.302,0.229 10 false *10 1.604,3.156 1.906,3.385 0.302,0.229 10 false *9 2.052,4.385 2.354,4.615 0.302,0.229 10 false *a

VSC Operation (Turning Right)
Item VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) On (Closed) ← ←
*12 SR Off (Closed) ← ← ←
*d Wheel Cylinder Pressure - - - -
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - - - -
Rear Brake RH *6 SH Off (Open) ← ← ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



h.

Hill-start Assist Control

i.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU computes the backward movement of the vehicle that occurs when the vehicle starts off on a hill. Then, the skid control ECU controls the fluid pressure that is generated by the pump and pump motor and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.


ii.

The skid control ECU determines the state of the backward movement of the vehicle while the driver is attempting to drive uphill, based on the speed sensors and the neutral start switch.


iii.

The skid control ECU determines the gradient of the hill, the acceleration state of the vehicle, the locked state and the rotation direction of each wheel through the speed sensors and the yaw rate sensor assembly. Then, the skid ECU computes the amount of brake control that will prevent the wheels from locking.


iv.

During this operation, the skid control ECU outputs a hill-start assist control operation signal to the combination meter. This causes the slip indicator light to blink, sends signals to the stop light control relay which turns on the stop light.


v.

The hill-start assist control operates for approximately five seconds. At this time, the skid control ECU informs the driver by the slow and intermittent sound of the buzzer in the combination meter assembly. After this, the skid control ECU alerts the driver by using the quick and intermittent sound of the buzzer in the combination meter assembly, and gradually releases the brake hydraulic pressure in order to end the hill-start assist control operation.

X104287E02
0.99,5.198 2.427,5.51 1.438,0.313 10 false 4WD CONTROL ECU 0.604,5.708 2.802,6.073 2.198,0.365 10 false YAW RATE SENSOR ASSEMBLY 5.333,4.958 5.719,5.271 0.385,0.313 10 false ECM 4.594,2.063 6.771,2.406 2.177,0.344 10 false SWITCHING SOLENOID VALVE 4.646,2.563 6.719,2.896 2.073,0.333 10 false CONTROL SOLENOID VALVE 3.708,5.583 4.927,5.927 1.219,0.344 10 false CAN (V bus) 1.083,4.51 1.729,4.875 0.646,0.365 10 false BUZZER 3.219,1.99 3.885,3 0.667,1.01 10 false SKID CONTROL ECU 0.563,3.365 2.073,4 1.51,0.635 10 false COMBINATION METER ASSEMBLY 0.604,4.115 2.188,4.448 1.583,0.333 10 false SLIP INDICATOR LIGHT 0.771,0.292 2.073,0.615 1.302,0.323 10 false SPEED SENSOR 0.281,1.021 2.51,1.344 2.229,0.323 10 false STOP LIGHT SWITCH ASSEMBLY 4,4.448 6.885,4.813 2.885,0.365 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 4.729,1.24 6.625,1.792 1.896,0.552 10 false ACCUMULATOR PRESSURE SENSOR 4.948,0.417 6.354,1.031 1.406,0.615 10 false MASTER CYLINDER PRESSURE SENSOR 4.813,3.104 6.469,3.781 1.656,0.677 10 false BRAKE BOOSTER PUMP ASSEMBLY 0.896,2.521 1.854,2.844 0.958,0.323 10 false STOP LIGHT 0.354,1.885 2.417,2.208 2.063,0.323 10 false STOP LIGHT CONTROL RELAY

X102461E10
5.438,3.094 5.75,2.979 true 4.427,3.073 4.646,2.813 true 3.448,3.083 3.656,2.781 true 1.771,3.24 2.083,3.115 true 4.604,4.396 4.906,4.625 0.302,0.229 10 false *d 4.042,4.396 4.344,4.625 0.302,0.229 10 false *c 2.625,4.396 2.927,4.625 0.302,0.229 10 false *b 5.49,2.188 5.792,2.417 0.302,0.229 10 false *8 4.51,2.188 4.813,2.417 0.302,0.229 10 false *7 3.521,2.188 3.823,2.417 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.74,1.385 3.042,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.188 2.823,2.417 0.302,0.229 10 false *5 5.76,2.854 6.063,3.083 0.302,0.229 10 false *12 4.573,2.625 4.875,2.854 0.302,0.229 10 false *11 3.573,2.583 3.875,2.813 0.302,0.229 10 false *10 1.604,3.146 1.906,3.375 0.302,0.229 10 false *9 2.052,4.396 2.354,4.625 0.302,0.229 10 false *a

Hill-start Assist Control Operation
Item Hill-start Assist Control Not Activated Hill-start Assist Control Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



i.

Downhill Assist Control

i.

Based on the information provided by various sensors, switches, and the engine ECU, the skid control ECU determines the conditions that enable downhill assist control operation. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valve to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.


ii.

The skid control ECU computes the vehicle speed, travel direction, and the gradient of the hill in accordance with the signals that are input by the speed sensor and the yaw rate sensor assembly, and effects brake control to attain the target vehicle speed. The target vehicle speed is determined by the direction of the vehicle.

Downhill Assist Control Target Vehicle Speed
Travel Direction Forward 5 to 7 km/h (3 to 4 mph)
Backward 3 to 5 km/h (2 to 3 mph)


iii.

During the downhill assist control operation, the skid control ECU outputs signals to the stop light control relay to cause the stop light to turn on, and to the combination meter to cause the slip indicator light to blink.

X104281E03
4.75,5.635 6.365,6.281 1.615,0.646 10 false 4WD CONTROL ECU 4.406,6.25 6.906,6.75 2.5,0.5 10 false YAW RATE SENSOR ASSEMBLY 0.354,2.115 2.333,2.917 1.979,0.802 10 false DOWNHILL ASSIST CONTROL SWITCH 5.167,5.052 6.573,5.729 1.406,0.677 10 false ECM 0.333,1.281 2.323,2.135 1.99,0.854 10 false CENTER DIFFERENTIAL LOCK DETECTION SWITCH 4.594,2.292 6.979,2.938 2.385,0.646 10 false SWITCHING SOLENOID VALVE 4.646,2.99 6.948,3.573 2.302,0.583 10 false CONTROL SOLENOID VALVE 2.99,5.333 4.031,5.875 1.042,0.542 10 false CAN (V bus) 3.229,2 3.99,3.01 0.76,1.01 10 false SKID CONTROL ECU 0.573,4.135 2.083,4.813 1.51,0.677 10 false COMBINATION METER ASSEMBLY 0.594,4.927 2.385,5.438 1.792,0.51 10 false SLIP INDICATOR LIGHT 0.354,5.313 2.313,6.073 1.958,0.76 10 false DOWNHILL ASSIST CONTROL INDICATOR LIGHT 0.76,0.292 2.219,0.844 1.458,0.552 10 false SPEED SENSOR 0.292,0.781 2.688,1.438 2.396,0.656 10 false STOP LIGHT SWITCH ASSEMBLY 3.698,4.635 6.844,5.229 3.146,0.594 10 false HYDRAULIC BRAKE BOOSTER ASSEMBLY 4.729,1.333 6.604,2.01 1.875,0.677 10 false ACCUMULATOR PRESSURE SENSOR 4.948,0.417 6.344,1.125 1.396,0.708 10 false MASTER CYLINDER PRESSURE SENSOR 4.813,3.594 6.469,4.354 1.656,0.76 10 false BRAKE BOOSTER PUMP ASSEMBLY 0.323,2.979 2.667,3.583 2.344,0.604 10 false STOP LIGHT CONTROL RELAY 0.938,3.625 2.083,4.146 1.146,0.521 10 false STOP LIGHT

X102461E10
5.438,3.094 5.75,2.979 true 4.427,3.073 4.646,2.813 true 3.448,3.083 3.656,2.781 true 1.771,3.24 2.083,3.115 true 4.604,4.396 4.906,4.625 0.302,0.229 10 false *d 4.042,4.396 4.344,4.625 0.302,0.229 10 false *c 2.625,4.396 2.927,4.625 0.302,0.229 10 false *b 5.49,2.188 5.792,2.417 0.302,0.229 10 false *8 4.51,2.188 4.813,2.417 0.302,0.229 10 false *7 3.521,2.188 3.823,2.417 0.302,0.229 10 false *6 4.635,1.385 4.938,1.615 0.302,0.229 10 false *4 3.74,1.385 4.042,1.615 0.302,0.229 10 false *3 2.74,1.385 3.042,1.615 0.302,0.229 10 false *2 1.906,1.385 2.208,1.615 0.302,0.229 10 false *1 2.521,2.188 2.823,2.417 0.302,0.229 10 false *5 5.76,2.854 6.063,3.083 0.302,0.229 10 false *12 4.573,2.625 4.875,2.854 0.302,0.229 10 false *11 3.573,2.583 3.875,2.813 0.302,0.229 10 false *10 1.604,3.146 1.906,3.375 0.302,0.229 10 false *9 2.052,4.396 2.354,4.625 0.302,0.229 10 false *a

Downhill Assist Control Operation
Item Downhill Assist Control Not Activated Downhill Assist Control Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SH Off (Open) ← On (Closed) ←
*11 SR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SH Off (Open) ← On (Closed) ←
*12 SR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SH Off (Open) ← On (Closed) ←
*9 SR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SH Off (Open) ← On (Closed) ←
*10 SR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder




FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors, or brake actuator, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTC and check function, refer to the 4RUNNER Repair Manual (Pub. No. RM1440E).