FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Combination Meter Assembly | Brake System Warning Light | ·
Lights up to alert the driver when the skid control ECU detects a malfunction in the EBD. ·
Lights up to alert the driver when the brake fluid level is low. ·
Lights up to alert the driver that the hydraulic pressure of the brake booster accumulator assembly in the hydraulic brake booster assembly has decreased. ·
Lights up to inform the driver of the parking brake condition. |
| ABS Warning Light | Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS. | |
| Slip Indicator Light | Blinks to inform the driver when the TRC, A-TRAC, AUTO LSD, VSC, hill-start assist control, downhill assist control and trailer sway control is operational. | |
| TRC OFF Indicator Light | Lights up to inform the driver that the TRC OFF mode is entered using the VSC OFF switch. | |
| VSC OFF Indicator Light | Lights up to inform the driver that the VSC OFF mode is entered using the VSC OFF switch. | |
| Downhill Assist Control Indicator Light | Lights up to inform the driver when the downhill assist control switch turned on. | |
| Buzzer | Sounds intermittently to inform the driver that the hill-start assist control is active. | |
| Front and Rear Speed Sensors | Detects the wheel speed of each of the 4 wheels. | |
| Yaw Rate and Acceleration Sensor
(Built-in Deceleration Sensor) |
·
Detects the vehicle's longitudinal and lateral acceleration. ·
Detects the vehicle's yaw rate. |
|
| Steering Angle Sensor
(Spiral Cable Sub-assembly) |
Detects the direction and angle of the steering wheel. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Parking Brake Switch Assembly | Detects that the parking brake lever is pulled up. | |
| Center Differential Lock Detection Switch
(Built-into Transfer Shift Actuator Assembly) |
Detects the center differential lock condition. | |
| VSC OFF Switch | Enables the driver to select the "Normal Mode", "TRC OFF Mode", or "VSC OFF Mode". | |
| Downhill Assist Control Switch | Turns the downhill assist control on and off. | |
| Hydraulic Brake Booster Assembly | Changes the brake fluid path based on the signals from the skid control ECU during the operations of the brake control functions in order to control the fluid pressure that is applied to the wheel cylinders. | |
| Brake Fluid Level Warning Switch
(Built-into Hydraulic Brake Booster Assembly) |
Detects the low brake fluid level. | |
| Master Cylinder Pressure Sensor
(Built-into Hydraulic Brake Booster Assembly) |
Detects the master cylinder pressure and outputs this signal to the skid control ECU. | |
| Accumulator Pressure Sensor
(Built-into Hydraulic Brake Booster Assembly) |
Monitors the hydraulic pressure of the brake booster accumulator assembly and outputs this signals for the brake booster pump assembly control. | |
| Switching Solenoid Valve
(Built-into Hydraulic Brake Booster Assembly) |
Switches the brake hydraulic path when the brake control system is activated. | |
| Control Solenoid Valve
(Built-into Hydraulic Brake Booster Assembly) |
Controls the hydraulic pressure that is applied to the wheel cylinders during brake control. | |
| Brake Booster Pump Assembly
(Built-into Hydraulic Brake Booster Assembly) |
Draws up the brake fluid from the brake master cylinder reservoir and provides high hydraulic pressure to the brake booster accumulator assembly. | |
| Skid Control ECU | Judges the vehicle driving condition based on signals from each sensor, and sends brake control signals to the hydraulic brake booster Assembly. | |
| Four Wheel Drive Control ECU | Sends the transfer drive mode. | |
| ECM | ·
Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU. ·
Based on the signals received from the skid control ECU, controls the engine output. |
|
OPERATING CONDITION
The brake control function vary by the transfer drive mode as shown in the following table:
| Brake Control Function | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| ABS | EBD | Brake Assist | TRC | A-TRAC | AUTO LSD | VSC | Hill-start
Assist Control |
Downhill
Assist Control |
Trailer
Sway Control |
| ○ | ○ | ○ | ○ | X | ○ | ○ | ○ | X | ○ |
| Transfer
Drive Mode |
Brake Control Function | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| ABS | EBD | Brake Assist | TRC | A-TRAC | AUTO LSD | VSC | Hill-start
Assist Control |
Downhill
Assist Control |
Trailer
Sway Control |
|
| H4F | ○ | ○ | ○ | ○ | X | X | ○ | ○ | X | ○ |
| H4L | ○ | ○ | ○ | ○ | X | X | ○ | ○ | X | ○ |
| L4L | ○ | ○ | ○ | X | ○ | X | X | ○ | ○ | X |
○: Operates
X: Not operates
Hill-start assist control
The hill-start assist control operates when all of the following conditions have been met:
| Hill-start Assist Control Operation Condition | ·
The shift lever is in D or S. ·
The brake pedal is not depressed. ·
The rear differential lock switch is off. ·
The skid control ECU has detected the backward movement of the vehicle when the driver is starting off on a hill. |
The hill-start assist control stops operating when any of the following conditions have been met:
| Hill-start Assist Control Ending Condition | ·
The shift lever is in any position other than D or S. ·
The brake pedal is depressed. ·
The rear differential lock switch is on. ·
Approximately 5 seconds have passed since control commenced. |
Downhill Assist Control
The hill-start assist control operates when all of the following conditions have been met:
| Downhill Assist Control Operation Condition | ·
The downhill assist control switch is on ·
The transfer drive mode is in L4L. ·
The accelerator pedal and brake pedal is not depressed. ·
Descending a hill at a vehicle speed of 25 km/h (16 mph) or less. |
The downhill assist control stops operating when any of the following conditions have been met:
| Downhill Assist Control Ending Condition | ·
The downhill assist control switch is off. ·
The transfer drive mode is in any position other than or L4L. ·
The accelerator pedal or brake pedal is depressed. |
SYSTEM CONTROL
| Control | Outline |
|---|---|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force distribution (EBD) | The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist | ·
The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance. ·
If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force. |
| Traction Control (TRC) | The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. |
| Active Traction Control (A-TRAC) | A-TRAC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD effect. |
| AUTO LSD | Briefly pressing the VSC OFF switch in normal mode enters TRC OFF mode, allowing the AUTO LSD to operate. The AUTO LSD achieves a function equivalent to that of an LSD system through the use of the TRC. The AUTO LSD applies brake hydraulic pressure to a slipping wheel to reduce the difference in rotation speed between the left and right drive wheels. This causes driving torque to be transmitted to the wheel opposite the slipping wheel. |
| Vehicle Stability Control (VSC) | The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, such as may occur while cornering. |
| Hill-start Assist Control | Hill-start assist control detects the backward descent of the vehicle and effects 4-wheel hydraulic pressure control to reduce the backward speed of the vehicle. As a result, the vehicle can be started off on a hill more easily. |
| Downhill Assist Control | When the DAC switch is pressed with transfer drive mode in and L4L, and without accelerator and brake pedals operation, downhill assist control activates to effect 4-wheel hydraulic pressure control, in order to maintain a constant low vehicle speed without causing the wheels to become locked. Thus, the vehicle can descend a steep hill in a stable manner. |
| Trailer Sway Control | The trailer sway control mitigates the phenomenon of the trailer sway by controlling the brakes and engine torque for each wheel when trailer sway phenomenon * is detected. |
*:Trailer sway is a phenomenon that occurs when the trailer swings side to side caused by crosswinds, steering, uneven road surfaces, etc., due to improper adjustment of torque load.
Anti-lock Brake System (ABS)
The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.
| *A | Models with ABS | *B | Models without ABS |
| *a | Brake Operation | - | - |
Electronic Brake Force Distribution (EBD)
This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.
During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.
|
Control Moment |
|
Brake Force |
Brake Assist
In the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the hydraulic brake booster assembly to increase the brake fluid pressure, which increases the brake force.
Traction Control (TRC)
The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Simultaneously with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.
| *A | Models without TRC | *B | Models with TRC |
| *1 | ECM
- Engine Output Control |
*2 | Brake Actuator Assembly
- Hydraulic Brake Control |
| *a | Brake Slipping Drive Wheel | - | - |
|
Slippery Surface | - | - |
Active Traction Control (A-TRAC)
When the vehicle drive mode is L4L, the A-TRAC helps restrain wheelspin by controlling the brake hydraulic pressure that is applied to the spinning wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an effect that is similar to Limited Slip Differential (LSD).
It independently controls the brake hydraulic pressure to the four wheels in accordance with the extent of the slippage at the wheels, as detected by the skid control ECU.
AUTO LSD
Briefly pressing the VSC OFF switch in normal mode allows the AUTO LSD to operate (TRC OFF mode is selected). The AUTO LSD achieves the LSD effect by regulating the hydraulic pressure that acts on the drive wheels.
TRC enhances the start-off performance of the vehicle during low-grip surface conditions, such as snow or mud, by restricting the acceleration effort during a start-off, in order to help prevent the wheels from spinning.
The AUTO LSD enhances the acceleration effort, in order to apply greater drive torque to the wheel that has grip. Thus, this function enables the vehicle to get unstuck if a wheel loses its grip, and enhances the vehicle's start-off performance when high-resistance surface conditions exist, such as loose gravel or sand.
Vehicle Stability Control (VSC)
The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below:
| *a | Front Wheel Skid Tendency (Understeer)
- When the front wheels lose grip in relation to the rear wheel |
*b | Rear Wheel Skid Tendency (Oversteer)
- When the rear wheels lose grip in relation to the front wheels |
To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle yaw rate, and vehicle's lateral acceleration, which are then calculated by the skid control ECU.
Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (a target yaw rate is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.
| *a | Actual Locus of Travel (Actual Yaw Rate) | *b | Locus of Travel Based on the Target Yaw Rate |
Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.
| *a | Travel Direction of Vehicle's Center of Gravity | *b | Movement of Vehicle |
| *c | Slip Angle | - | Slip Angle |
When the skid control ECU determines that the vehicle exhibits a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of the front or rear wheels to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.
When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the rear wheel on the inner circle of the turn in order to help restrain the front wheel skid tendency.
|
Control Moment |
|
Brake Force |
When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.
|
Control Moment |
|
Brake Force |
Hill-start Assist Control
When the vehicle starts off on a steep or slippery hill, the vehicle may descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, the hill-start assist control temporarily (approximately 5 seconds at the maximum) applies the brakes to the 4 wheels in order to prevent vehicle from descending backward.
Without the hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the hill-start assist control, however, the driver can start off easily and operate the pedal in a relaxed manner, because the hill-start assist control prevents the vehicle from descending backward.
Downhill Assist Control
When the vehicle is descending a steep hill and the engine brake alone cannot provide a sufficient deceleration force while the transfer drive mode is in or L4L, downhill assist control effects 4 wheels brake control to maintain a constant, low vehicle speed. Thus, the vehicle is able to descend in a stable manner without causing the wheels to become locked.
When the vehicle descends a steep hill without downhill assist control, the driver must pay close attention to the brake and accelerator pedal maneuvers. However, with downhill assist control, the driver can concentrate on the steering operation, without accelerator and brake pedals operation.
Downhill assist control enables the vehicle to maintain stability because it can descend a slippery hill at low speeds without causing the wheels to become locked.
Trailer Sway Control
Trailer sway control is a part of the VSC function. Accordingly, if the VSC OFF mode or VSC is not functioning normally, trailer sway control will not operate.
Trailer sway control will be unable to stabilize the vehicle if a trailer is being towed which cannot be physically controlled due to the influence of the vehicle, road surface, driving conditions and so on.
If the vehicle is towing a trailer with an inappropriate hitch load, trailer sway could be caused by crosswinds, imbalance caused by load, or the driver's steering. Trailer sway control reduces trailer sway by controlling the engine output and the braking of each wheel.
The skid control ECU detects the occurrence of trailer sway based on signals from the yaw rate & deceleration sensor and the steering angle sensor.
Trailer sway can be reduced by decelerating the vehicle. When the skid control ECU detects trailer sway, it controls the brakes of each wheel while simultaneously requesting engine output control from the ECM and reducing vehicle speed.
Moreover, by using brake control to reduce the yaw moment caused by trailer sway, trailer sway can be reduced more quickly than by simply decelerating the vehicle.
The slip indicator light on the combination meter flashes when trailer sway control is in operation. Also, the stop light illuminates to inform vehicles behind that the vehicle is decelerating.
FUNCTION
VSC OFF Switch
The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.
| *A | Standard Type | *B | Optitron Type |
| *1 | Combination Meter Assembly | *2 | VSC OFF Switch |
| *a | TRC OFF Indicator Light | *b | VSC OFF Indicator Light |
The VSC OFF switch can select 3 modes (mode A, mode B, and mode C).
Briefly pressing the VSC OFF switch in mode A selects the mode B.
Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the mode C.
Briefly pressing the VSC OFF switch in the mode B or mode C or turning the ignition switch off returns to the mode A.
When TRC is not operating, the TRC OFF indicator light will illuminate.
When VSC is not operating, the VSC OFF indicator light will illuminate.
| Transfer Drive Mode | Brake Control Function | VSC OFF Switch Mode | ||
|---|---|---|---|---|
| Mode A | Mode B | Mode C | ||
| H4F | TRC | Operates | Not Operates | Not Operates |
| A-TRAC | Not Operates | Not Operates | Not Operates | |
| VSC | Operates | Operates | Not Operates | |
| H4L | TRC | Operates | Not Operates | Not Operates |
| A-TRAC | Not Operates | Not Operates | Not Operates | |
| VSC | Operates | Operates | Not Operates | |
| L4L | TRC | Not Operates | - | Not Operates |
| A-TRAC | Operates | - | Not Operates | |
| VSC | Not Operates | - | Not Operates | |
CONSTRUCTION
Yaw Rate and Acceleration Sensor
This sensor has a built-in deceleration sensor.
The yaw rate sensor detects the vehicle's yaw rate.
The deceleration sensor detects the vehicle's longitudinal and lateral acceleration
| *1 | Yaw Rate and Acceleration Sensor | *2 | Deceleration Sensor |
| *3 | Yaw Rate Sensor | - | - |
| *a | Cross Section | - | - |
Steering Angle Sensor
The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.
Speed Sensor
Active type speed sensors, which can detect the rotational direction of the wheel, have been provided. This sensor contains 2 Magnetic Resistance Elements (MREs).
The magnet type rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.
| *1 | Front Speed Sensor | *2 | Sensor Rotor |
| *3 | Rear Speed Sensor | - | - |
| *a | Front Axle | *b | Rear Axle |
Hydraulic Brake Booster Assembly
The brake actuator portion in hydraulic brake booster consists of 4 switching solenoid valves, 8 control solenoid valves and skid control ECU.
The pressure increase mode, the pressure holding mode, and the pressure reduction mode are effected based on the combination of these solenoid valves that are turned on and off, in order to control the hydraulic pressure that is applied to each of the wheel cylinders.
4 switching solenoid valves are used: 2 (SMCF, SREA) in the front brake fluid path, 1 (SREC) in the rear brake fluid path, and 1 (STR) in the accumulator fluid path. The switching solenoid valves open and closed in accordance with the control signals from the skid control ECU in order to switch the respective brake fluid path.
8 control solenoid valves are used for the 4 wheels (2 types per wheel: pressure holding solenoid and pressure reduction solenoid).
| *1 | STR (Traction Solenoid Valve) | *2 | SREC (Regulator Cut Solenoid Valve) |
| *3 | SREA
(Regulator Apply for Front Solenoid Valve) |
*4 | SMCF (Master Cut for Front Solenoid Valve) |
| *5 | Master Cylinder Pressure Sensor | *6 | SH (Pressure Holding Solenoid Valve) |
| *7 | SH (Pressure Holding Solenoid Valve) | *8 | SH (Pressure Holding Solenoid Valve) |
| *9 | SH (Pressure Holding Solenoid Valve) | *10 | SR (Pressure Holding Solenoid Valve) |
| *11 | SR (Pressure Holding Solenoid Valve) | *12 | SR (Pressure Holding Solenoid Valve) |
| *13 | SR (Pressure Holding Solenoid Valve) | - | - |
| *a | Rear LH | *b | Rear RH |
| *c | Front LH | *d | Front RH |
|
To Brake Master Cylinder Reservoir |
|
From Brake Booster Accumulator Assembly |
|
From Brake Master Cylinder | - | - |
OPERATION
Speed Sensor
The active type speed sensor uses 2 Magnetic Resistance Elements (MREs) to detect magnetic field changes caused when the sensor rotor rotates, and the speed sensor outputs the detected information to the skid control ECU as digital pulses.
To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by the 2 Magnetic Resistance Elements (MREs).
Upon receiving this signal, the speed sensor outputs a forward or backward wave.
To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.
ABS and EBD
Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks wheel slipping conditions.
The skid control ECU compares the speed sensor signals of the front and rear, judges the slipping condition of the rear wheel, and operates the EBD.
When a wheel is about to lock, the ABS operation starts in order to regulate the hydraulic pressure at the wheel cylinders while switching between the 3 modes: pressure increase, pressure holding, and pressure reduction.
| Item | EBD Not Activated | EBD Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | |
| *2 | SREC | Off (Open) | Off (Open) | Off (Open) | Off (Open) | ||
| *3 | SREA | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *4 | SMCF | Off (Open) | Off (Open) | Off (Open) | Off (Open) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | Off (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *d | Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake LH | *5 | SH | Off (Open) | On (Closed) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *a | Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake RH | *6 | SH | Off (Open) | On (Closed) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *b | Wheel Cylinder Pressure | - | - | - | - | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
| Item | ABS Not Activated | ABS Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | |
| *2 | SREC | Off (Open) | Off (Open) | Off (Open) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Open) | ||
| *d | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
While the front wheels are in the ABS operation, SREA and SMCF are on. While only rear wheels are in the ABS operation, SREA and SMCF are off.
Brake Assist
If an emergency braking situation has occurred, it is detected by the skid control ECU based on the vehicle speed signal from the speed sensor, the brake pedal application speed from the master cylinder pressure sensor, and the signal representing the amount of pedal effort. Then, the skid control ECU actuates each solenoid valve. As a result, the pressure from the brake booster accumulator assembly is applied to the wheel cylinders. The accumulator pressure that is applied to the wheel cylinders generates a higher pressure than the master cylinder.
| Item | Brake Assist Not Activated | Brake Assist Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *d | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
TRC
The fluid pressure that is generated by the brake booster pump assembly is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the pressure to the wheel cylinders of the drive wheels is controlled in the following 3 modes: increase mode, holding mode, and reduction mode, to restrain the slippage of the drive wheels.
The skid control ECU outputs a TRC operation signal to the ECM. Upon receiving this signal, the ECM effects engine output control.
If the accumulator pressure drops during this operation, the skid control ECU receives the signals from the accumulator pressure sensor and actuates the brake booster pump assembly to ensure the proper accumulator pressure.
| Item | TRC Not Activated | TRC Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *d | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
A-TRAC
Based on the vehicle speed that has been calculated from each speed sensor and the signals of the yaw rate and deceleration sensor, the skid control ECU computes the target control speed.
The skid control ECU compares the target control speed and the wheel speed to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valve of the hydraulic brake booster assembly to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.
The fluid pressure control of the A-TRAC independently controls the brake of each wheel by operating the individual solenoid valves in accordance with the signals received from the skid control ECU. The brake of each wheel is controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.
| Item | A-TRAC Not Activated | A-TRAC Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *d | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
AUTO LSD
AUTO LSD is a function that has effects similar to a mechanical type LSD. AUTO LSD employs the TRC to control brake hydraulic pressure and engine output.
The Skid Control ECU detects slippage that occurs as a result of a rotational difference between the drive wheel and the non-driven wheel. Via the TRC, the AUTO LSD detects the wheel slip that occurs (the wheel that is rotating faster) , based on the rotational difference of the right and left drive wheels, and puts AUTO LSD into action.
| Item | AUTO LSD
Not Activated |
AUTO LSD Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Open) | On (Closed) | On (Closed) | On (Closed) | |
| *2 | SREC | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *3 | SREA | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *4 | SMCF | Off (Open) | Off (Open) | Off (Open) | Off (Open) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | Off (Open) | Off (Open) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *c | Wheel Cylinder Pressure | - | - | - | - | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | Off (Open) | Off (Open) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *e | Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
VSC
Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the vehicle's yaw moment. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency of the front wheels or the rear wheels to skid is restrained.
At this time, the skid control ECU outputs a VSC operation signal to the ECM and the combination meter assembly. Upon receiving this signal, the ECM controls the engine output. The slip indicator light will blink in the combination meter assembly.
During front wheel skid restraining control, the brakes of the rear wheels and front wheel of the outer side of the turn are applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a front wheel skid while the vehicle is making a right turn.
| Item | VSC Not Activated | VSC Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | On (Closed) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *d | Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
During rear wheel skid restraining control, the front wheel brake of the outer side of the turn is applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which the brake might be applied to the rear brake of the outer side of the turn. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a rear wheel skid while the vehicle is making a right turn.
| Item | VSC Not Activated | VSC Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | On (Closed) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| *d | Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | - | - | - | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | Off (Open) | Off (Open) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
Hill-start Assist Control
Based on the information provided by various sensors, switches, and the ECM, the skid control ECU computes the backward movement of the vehicle that occurs when the vehicle starts off on a hill. Then, the skid control ECU controls the fluid pressure that is generated by the pump and pump motor and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.
The skid control ECU determines the state of the backward movement of the vehicle while the driver is attempting to drive uphill, based on the speed sensors and the neutral start switch.
The skid control ECU determines the gradient of the hill, the acceleration state of the vehicle, the locked state and the rotation direction of each wheel through the speed sensors and the yaw rate sensor assembly. Then, the skid ECU computes the amount of brake control that will prevent the wheels from locking.
During this operation, the skid control ECU outputs a hill-start assist control operation signal to the combination meter. This causes the slip indicator light to blink, sends signals to the stop light control relay which turns on the stop light.
The hill-start assist control operates for approximately five seconds. At this time, the skid control ECU informs the driver by the slow and intermittent sound of the buzzer in the combination meter assembly. After this, the skid control ECU alerts the driver by using the quick and intermittent sound of the buzzer in the combination meter assembly, and gradually releases the brake hydraulic pressure in order to end the hill-start assist control operation.
| Item | Hill-start Assist Control Not Activated | Hill-start Assist Control Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *d | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
Downhill Assist Control
Based on the information provided by various sensors, switches, and the engine ECU, the skid control ECU determines the conditions that enable downhill assist control operation. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valve to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.
The skid control ECU computes the vehicle speed, travel direction, and the gradient of the hill in accordance with the signals that are input by the speed sensor and the yaw rate sensor assembly, and effects brake control to attain the target vehicle speed. The target vehicle speed is determined by the direction of the vehicle.
| Travel Direction | Forward | 5 to 7 km/h (3 to 4 mph) |
| Backward | 3 to 5 km/h (2 to 3 mph) |
During the downhill assist control operation, the skid control ECU outputs signals to the stop light control relay to cause the stop light to turn on, and to the combination meter to cause the slip indicator light to blink.
| Item | Downhill Assist Control Not Activated | Downhill Assist Control Activated | |||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Switching Solenoid Valve | *1 | STR | Off (Closed) | On (Open) | On (Open) | Off (Closed) | |
| *2 | SREC | Off (Open) | On (Closed) | On (Closed) | Off (Open) | ||
| *3 | SREA | Off (Closed) | On (Open) | On (Open) | On (Open) | ||
| *4 | SMCF | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Control Solenoid Valve | Front Brake LH | *7 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| *11 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *c | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Front Brake RH | *8 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *12 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *d | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake LH | *5 | SH | Off (Open) | Off (Open) | On (Closed) | On (Closed) | |
| *9 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *a | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
| Rear Brake RH | *6 | SH | Off (Open) | Off (Open) | On (Closed) | Off (Open) | |
| *10 | SR | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| *b | Wheel Cylinder Pressure | - | Increases | Holds | Reduces | ||
|
To Brake Master Cylinder Reservoir | ||||||
|
From Brake Booster Accumulator Assembly | ||||||
|
From Brake Master Cylinder | ||||||
FAIL-SAFE
If a failure occurs in the skid control ECU, sensors, or brake actuator, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.
This system has a sensor signal check (test mode) function.
For details of DTC and check function, refer to the 4RUNNER Repair Manual (Pub. No. RM1440E).