Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
NM1440E _55 Steering _056100 POWER ASSIST SYSTEMS _0273721 POWER STEERING SYSTEM UN GENERAL/CONTROL/DETAILS F

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Rack and Pinion Power Steering Gear Assembly Increases operation force of the steering wheel and transmits operation force to the front wheel.
Vane Pump Assembly Drives in accordance with the engine to pump power steering fluid to the steering gear assembly.
VFC Solenoid Valve
(Built-in Vane Pump)
Controls the discharge flow rate and is controlled by the power steering ECU.
Vane Pump Oil Reservoir Assembly Stores the power steering fluid.
Combination Meter Assembly
- Power Steering Warning Light
Light up to alert the driver that the power steering ECU detects a malfunction in the power steering system.
Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Power Steering ECU Assembly Calculates the optimum discharge flow rate in accordance with the vehicle condition, and controls the VFC solenoid valve.
Skid Control ECU Sends the vehicle speed signal.
ECM Sends the engine speed signal.


SYSTEM CONTROL


a.

The power steering ECU effects the following controls:

Control Function
Flow Rate Control
·

It effects control in accordance with the vehicle speed, steering angle, and steering speed conditions. It effects assist control when the steering wheel is being operated and standby control when the steering wheel is not being operated. Thus, it prevents the vane pump from discharging excessive flow, which lightens the load on the engine and improves fuel economy. Also, the following corrections are made to determine an optimal discharge flow rate.

·

The control feature of allowing the discharge flow rate to change as little as possible in accordance with steering speed and vehicle speed when in L4 position is achieved.


Steering Angle Correction Determines the discharge flow rate in accordance with driving conditions, such as steering at standstill, cornering, or straightline driving.
Steering Return Correction Determines the discharge flow rate for returning the steering wheel to its neutral position after the steering wheel is operated.
Engine Speed Correction Determines the discharge flow rate in accordance with the engine speed.

X102427E02
2.469,7.25 5.375,7.573 2.906,0.323 10 false Calculates Time to Achieve Target Flow Rate 2.604,6.417 3.635,6.656 1.031,0.24 10 false Standby Control 2.115,4.104 3.281,4.719 1.167,0.615 10 false Calculates Engine Speed 0.396,1.385 1.885,1.771 1.49,0.385 10 false Steering Angle Sensor 0.646,0.563 1.667,0.927 1.021,0.365 10 false Steering Angle 0.625,0.969 1.698,1.302 1.073,0.333 10 false Neutral Position 0.563,2.594 1.833,2.906 1.271,0.313 10 false Skid Control ECU 0.667,2.115 1.698,2.427 1.031,0.313 10 false Vehicle Speed 0.563,3.625 1.833,3.938 1.271,0.313 10 false 4WD Control ECU 0.573,3.156 1.844,3.469 1.271,0.313 10 false Transfer Position 0.667,4.26 1.74,4.573 1.073,0.313 10 false Engine Speed 0.938,4.75 2.208,5.063 1.271,0.313 10 false ECM 0.667,7.635 1.552,8.208 0.885,0.573 10 false VFC Solenoid Valve 2.094,0.521 3.927,0.833 1.833,0.313 10 false Calculates Steering Angle 2.063,0.99 3.896,1.302 1.833,0.313 10 false Calculates Steering Speed 4.563,0.583 6.188,1.281 1.625,0.698 10 false Determination Assist Control or Standby Control 2.094,1.969 3.26,2.573 1.167,0.604 10 false Calculates Vehicle Speed 5.052,1.698 6.531,2.01 1.479,0.313 10 false Calculates Flow Rate 5.094,2.146 6.49,2.458 1.396,0.313 10 false L4 Position Control 4.875,2.802 5.813,3.417 0.938,0.615 10 false Steering Angle Correction 4.875,3.51 5.854,4.083 0.979,0.573 10 false Steering Return Correction 4.948,4.188 5.854,4.792 0.906,0.604 10 false Engine Speed Correction 4.948,4.896 6.719,5.198 1.771,0.302 10 false Flow Rate Limit Process 2.115,3 3.177,3.677 1.063,0.677 10 false Detects Transfer Drive Mode 2.469,5.51 5.375,5.833 2.906,0.323 10 false Calculates Time to Achieve Target Flow Rate 2.74,6.063 3.646,6.344 0.906,0.281 10 false Assist Control 4.375,6.656 4.708,6.948 0.333,0.292 10 false Time 2.958,8 3.625,8.26 0.667,0.26 10 false Flow Rate 4.25,8.427 5.115,8.75 0.865,0.323 10 false Flow Rate 3.385,8.938 5.375,9.26 1.99,0.323 10 false Power Steering ECU Assembly


b.

Standby Control or Assist Control

i.

The standby control or assist control is performed in accordance with vehicle condition such as a vehicle speed, a steering angle, and a steering speed.

Control Standby Control Assist Control
Vehicle Condition Vehicle speed 0 km/h (0 mph) Steering Speed Equal 0 deg/s
(For 10 seconds or more)
Steering Speed Greater than 0 deg/s
Vehicle speed more than 0 km/h (0 mph) Steering Angle Less than 4.5°
(For 10 seconds or more)
Steering Angle Greater than or Equal to 4.5°


ii.

The assist flow rate is determined in accordance with the vehicle speed and steering speed.


iii.

For 3 seconds after the ignition switch is turned ON, the flow rate is controlled at 10.5 l/min. After that, the flow rate is controlled as shown in the graph below.

X102332E01
4.969,2.542 6.76,2.854 1.792,0.313 10 false Steering Speed (60 deg/s) 4.969,1.781 6.76,2.094 1.792,0.313 10 false Steering Speed (360 deg/s) 0.75,0.75 2.063,1.073 1.313,0.323 10 false : Standby Control 0.74,0.365 1.813,0.677 1.073,0.313 10 false : Assist Control 4.969,0.552 6.76,0.865 1.792,0.313 10 false Steering Speed (900 deg/s) 1.24,1.76 2.354,2.135 1.115,0.375 10 false Flow Rate (l/min) 2.969,3.146 4.354,3.438 1.385,0.292 10 false Vehicle Speed (km/h) 2.302,3.083 2.594,3.396 0.292,0.313 10 false 0


iv.

In off-road driving, the steering force amount is important information for understanding the condition of the contact between the tire and the road. Accordingly, this system has the control feature of allowing the discharge flow rate to change as little as possible in accordance with the vehicle speed and steering speed when in transfer drive mode L4.

X101416E01
1.177,1.604 2.323,1.948 1.146,0.344 10 false Flow Rate (l/min) 3.021,3.135 4.375,3.479 1.354,0.344 10 false Vehicle Speed (km/h) 2.354,3.146 2.75,3.49 0.396,0.344 10 false 0



c.

Steering Angle Correction

i.

Based on the steering angle and vehicle speed signals, this function corrects the flow rate in accordance with the driving conditions. Thus, it ensures an optimal steering feeling for every steering condition, such as steering at standstill, cornering, or straightline driving.


ii.

The correction flow rate is 0 l/min while the steering is operated with the vehicle at standstill or driving straight (steering angle is +/- 0° or less).


iii.

The correction flow rate decreases when the vehicle speed and steering angle increase.

X102333E01
4.958,1.76 6.844,2.083 1.885,0.323 10 false Steering Angle (+/- 180 deg) 4.958,1.427 6.781,1.75 1.823,0.323 10 false Steering Angle (+/- 60 deg) 2.354,2.292 2.646,2.635 0.292,0.344 10 false 0 4.958,0.656 6.823,0.979 1.865,0.323 10 false Steering Angle (+/- 4.5 deg) 0.521,1.24 2.333,1.792 1.813,0.552 10 false Correction Flow Rate (l/min) 2.271,0.677 2.563,1.021 0.292,0.344 10 false 0 2.979,2.302 4.333,2.656 1.354,0.354 10 false Vehicle Speed (km/h)




CONSTRUCTION


a.

Rack and Pinion Power Steering Gear Assembly

i.

Operability has been improved through a lightweight, compact rack and pinion type steering gear assembly.


ii.

A variable gear ratio type steering rack is used. This steering rack changes the gear ratio gradually by changing the gear teeth form. The gear ratio is set larger around the steering center and smaller around the end position. Thus, rack stroke around the end position is larger to reduce the steering operation while ensuring the moderate response around the steering center.

X102419

X102420E03
5.635,2.719 6.094,1.792 6.094,1.792 6.208,1.792 true 3.542,1.438 3.667,0.531 3.667,0.531 3.771,0.531 true 2.417,2.313 2.615,2.469 0.198,0.156 10 false *a 3.677,2.896 3.875,3.052 0.198,0.156 10 false *b 6.26,1.688 6.448,1.844 0.188,0.156 10 false *2 3.813,0.427 4,0.583 0.188,0.156 10 false *1

Text in Illustration
*1 Pinion Gear *2 Rack
*a Steering Center Position *b Steering End Position



b.

Vane Pump Assembly

i.

A compact and lightweight vane pump is used.


ii.

A VFC solenoid valve is provided to control the discharge flow rate.

X102421E02
4.688,0.938 5.229,0.594 5.229,0.594 5.365,0.594 true 5.417,0.49 5.604,0.646 0.188,0.156 10 false *1

Text in Illustration
*1 VFC Solenoid Valve - -

X102422E03
2.365,1.573 2.365,1.917 true 4.469,0.552 4.469,1.177 true 2.292,1.917 2.625,2.177 0.333,0.26 10 false *1 4.396,0.344 4.729,0.604 0.333,0.26 10 false *2

Text in Illustration (VFC Solenoid Valve)
*1 VFC Solenoid Valve *2 Flow Control Valve
V100136

To Rack and Pinion Power Steering Gear
V100137

From Vane Pump
V100138

To Vane Pumpr - -

X101420E01
1.979,1.354 2.698,1.917 0.719,0.563 10 false Flow Rate 3.365,2.365 3.896,2.635 0.531,0.271 10 false Current 0.188,0.125 3.458,0.479 3.271,0.354 10 false Flow Rate Characteristic of Solenoid Valve




FAIL-SAFE


a.

If the power steering ECU detects a malfunction in this system, it illuminates the power steering warning light to alert the driver of the malfunction.


b.

If a malfunction occurs in any of the sensors, the power steering ECU effects the following fail-safe control.

Fail-safe Control List
Malfunction Fail-safe Control
Steering Angle Signal
·

Fixes the steering angle to 0°

·

Fixes the steering speed to 360 deg/sec

·

Steering angle correction is canceled


Steering Zero Point memory
·

Fixes the steering angle to 0°

·

Steering angle correction is canceled


Vehicle Speed Signal
·

Fixes the vehicle speed to 40 km/h (24.9 mph)


Steering Angle Signal and Steering Zero Point Memory
·

Fixes the steering angle to 0°

·

Fixes the steering speed to 360 deg/sec

·

Steering angle correction is canceled


Steering Angle Signal and Vehicle Speed Signal
·

Fixes the steering angle to 0°

·

Fixes the steering speed to 360 deg/sec

·

Fixes the vehicle speed to 40 km/h (24.9 mph)

·

Fixes the discharge flow rate to 8.5 l/min.


Steering Zero Point Memory and Vehicle Speed Signal
·

Fixes the steering angle to 0°

·

Fixes the vehicle speed to 40 km/h (24.9 mph)

·

Steering angle correction is canceled


Steering Angle Signal, Steering Zero point Memory and Vehicle Speed Signal
·

Fixes the steering angle to 0°

·

Fixes the steering speed to 360 deg/sec

·

Fixes the vehicle speed to 40 km/h (24.9 mph)

·

Fixes the discharge flow rate to 8.5 l/min.





DIAGNOSIS


a.

If the power steering ECU detects a malfunction in the VFC power steering system, the power steering warning light will illuminate to inform the driver.


b.

At the same time, the Diagnostic Trouble Code (DTC) are stored in the memory. The DTC stored in the power steering ECU are output to an intelligent tester II connected to the DLC3. For details, refer to the 4RUNNER Repair Manual (Pub. No. RM1440E).