Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2009.08–2013.08
NM1440E _58 Vehicle Interior _056109 SUPPLEMENTAL RESTRAINT SYSTEMS _0273735 AIRBAG SYSTEM UN GENERAL/CONTROL/DETAILS F

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components have the following functions:

Component Function
Center Airbag Sensor Assembly
·

The center airbag sensor assembly receives signals from the deceleration sensor and safing sensor built into the center airbag sensor assembly and one of the front airbag sensors, determines whether the driver airbag, front passenger airbag, driver side knee airbag, passenger side knee airbag and front seat belt pretensioners should be activated. It also diagnoses system malfunctions.

·

The center airbag sensor assembly receives signals from the safing sensor built into the center airbag sensor assembly, side airbag sensors and floor side airbag sensor, and determines whether the front seat side airbag and curtain shield airbag should be activated. It also diagnoses system malfunctions.

·

The center airbag sensor assembly sends an airbag deployment signal to the ECM through the Controller Area Network (CAN) to operate the fuel pump control.


Airbag Assembly Driver and Front Passenger The airbag assemblies are used as supplements to the seat belts to help reduce impact to the occupants.
Front Seat Side LH/RH
Curtain Shield LH/RH
Front Airbag Sensor LH/RH Based on the deceleration of the vehicle during a frontal collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.
Side Airbag Sensor Assembly LH/RH Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.
Rear Airbag Sensor LH/RH
Floor Side Airbag Sensor The seat position sensor detects the slide position of the driver seat.
Front Seat Outer Belt Assembly Driver The front seat outer belt assemblies are used as supplements to help to reduce the impacts to the occupants.
Front Seat Inner Belt Assembly Driver Seat Belt Buckle Switch The driver seat belt buckle switch detects if the driver seat belt is fastened.
Combination Meter Assembly SRS Warning Light The SRS warning light turns to alert the driver when the center airbag sensor assembly detects a malfunction in the airbag system.



OPERATING CONDITION


a.

If the impact of a collision is greater than the specified value, the SRS is activated automatically. The center airbag sensor assembly include the safing sensor and deceleration sensor. The safing sensor is designed to turn on at a lower deceleration rate than the deceleration sensor.

i.

In case of a frontal collision, the center airbag sensor assembly determines whether airbag deployment or pretensioner activation is necessary based on signals from the deceleration sensor and the front airbag sensor. If the safing sensor turns on simultaneously, current flows to the squibs to deploy the SRS components as shown in the illustration below.


ii.

However, a deployment ignition signal may be output with the deceleration sensor on signal even without a signal from a front airbag sensor.

Y104856E03
0.302,0.521 2.031,0.833 1.729,0.313 10 false FRONT AIRBAG SENSOR 0.313,1.875 2.042,2.188 1.729,0.313 10 false Deceleration Sensor On 0.313,2.708 2.042,3.021 1.729,0.313 10 false Safing Sensor On 0.219,3.438 2,4.083 1.781,0.646 10 false CENTER AIRBAG SENSOR ASSEMBLY 4.167,1.021 6.792,1.333 2.625,0.313 10 false STEERING PAD (DRIVER SIDE SQUIB) 4.208,1.979 6.531,2.625 2.323,0.646 10 false FRONT PASSENGER SIDE AIRBAG ASSEMBLY 4.188,3.198 6.792,3.844 2.604,0.646 10 false FRONT SEAT OUTER BELT ASSEMBLY 3.073,2.333 3.51,2.698 0.438,0.365 10 false AND


iii.

In case of a side collision, the center airbag sensor assembly determines whether airbag deployment is necessary based on signals from the side airbag sensor assembly and safing sensor. If the safing sensor and side airbag sensor assembly turn on simultaneously, current flows to the squibs to deploy the SRS components shown in the illustration below.

V100406E07
4.979,1.063 6.323,1.688 1.344,0.625 10 false FRONT SEAT SIDE AIRBAG ASSEMBLY 5,2.094 6.354,2.688 1.354,0.594 10 false CURTAIN SHIELD AIRBAG ASSEMBLY 3.885,1.75 4.302,2.115 0.417,0.365 10 false AND 0.844,0.531 2.156,1.052 1.313,0.521 10 false Safing Sensor On 0.667,2.719 2.219,3.281 1.552,0.563 10 false SIDE AIRBAG SENSOR ASSEMBLY 0.208,1.24 2.781,1.938 2.573,0.698 10 false CENTER AIRBAG SENSOR ASSEMBLY OR FLOOR SIDE AIRBAG SENSOR


iv.

In case of a rear side collision, the center airbag sensor assembly determines whether airbag deployment is necessary based on signals from the rear airbag sensor and safing sensor. If the safing sensor and rear airbag sensor turn on simultaneously, current flows to the squibs to deploy the SRS components shown in the illustration below.

V100407E06
0.719,0.51 2.104,0.99 1.385,0.479 10 false Safing Sensor On 0.448,2.719 2.25,3.385 1.802,0.667 10 false REAR AIRBAG SENSOR 0.104,1.188 2.708,1.854 2.604,0.667 10 false CENTER AIRBAG SENSOR ASSEMBLY OR FLOOR SIDE AIRBAG SENSOR 4.792,1.604 6.5,2.26 1.708,0.656 10 false CURTAIN SHIELD AIRBAG ASSEMBLY 3.76,1.74 4.177,2.104 0.417,0.365 10 false AND




SYSTEM CONTROL


a.

Airbag for Frontal Collision

i.

There are 2 airbags which deploy in the event of a frontal collision: the steering pad and front passenger airbag assembly. These airbags deploy simultaneously. The steering pad and front passenger airbag assembly use dual-stage control.


ii.

The center airbag sensor assembly detects the information indicated below from various sources in order to activate the dual-stage control.


iii.

For a frontal collision, if a front airbag sensor detects an impact, it informs the center airbag sensor assembly. The center airbag sensor assembly causes the steering pad and front passenger airbag assembly to deploy. Meanwhile, the center airbag sensor assembly activates the seat belt pretensioners for the driver, front passenger.

Airbag Information Source
Driver Extent of Impact
·

Front Airbag Sensor (RH or LH)

·

Center Airbag Sensor Assembly


Seat Belt Condition Front Seat Inner Belt Assembly (Driver Seat Belt Buckle Switch) (Non-contact Type)
Front Passenger Extent of Impact
·

Front Airbag Sensor (RH or LH)

·

Center Airbag Sensor Assembly



Y104857E03
0.521,2.708 2.271,3.188 1.75,0.479 10 false FRONT SEAT INNER BELT ASSEMBLY LH 0.344,4.854 2.688,5.042 2.344,0.188 10 false COMBINATION METER ASSEMBLY 0.771,5.458 2.281,5.625 1.51,0.167 10 false SRS WARNING LIGHT 1.271,6.177 1.604,6.365 0.333,0.188 10 false ECM 2.76,6.469 3.583,6.781 0.823,0.313 10 false CAN (V Bus) 3.771,2.938 4.563,3.771 0.792,0.833 10 false CENTER AIRBAG SENSOR ASSEMBLY 3.146,0.26 5.573,0.594 2.427,0.333 10 false FRONT AIRBAG SENSOR LH or RH 5.573,1.948 7.01,2.448 1.438,0.5 10 false STEERING PAD (DRIVER SIDE SQUIB) 5.573,3.385 7.021,3.719 1.448,0.333 10 false FRONT SEAT OUTER BELT ASSEMBLY LH 5.573,5.125 6.979,5.521 1.406,0.396 10 false FRONT PASSENGER AIRBAG ASSEMBLY 1.073,1.167 1.677,1.375 0.604,0.208 10 false Collision 1.927,1.167 2.417,1.375 0.49,0.208 10 false Impact



b.

Airbag for Side/Side Rear Collision

i.

There are 2 airbags which deploy in the event of a severe side collision: the front seat side airbag assembly and curtain shield airbag assembly. These airbags deploy simultaneously.


ii.

For a side collision, if the side airbag sensor assembly detects an impact, it informs the center airbag sensor assembly, and the center airbag sensor assembly causes the front seat side and curtain shield airbag assemblies to deploy simultaneously.

Y104858E04
0.146,4.708 2.469,4.896 2.323,0.188 10 false COMBINATION METER ASSEMBLY 0.542,5.313 2.052,5.479 1.51,0.167 10 false SRS WARNING LIGHT 1.125,6.073 1.458,6.26 0.333,0.188 10 false ECM 2.594,6.365 3.594,6.521 1,0.156 10 false CAN (V Bus) 3.99,4.427 4.781,5.167 0.792,0.74 10 false CENTER AIRBAG SENSOR ASSEMBLY 3.375,0.438 4.938,0.958 1.563,0.521 10 false SIDE AIRBAG SENSOR ASSEMBLY (LH or RH)* 5.438,4.75 6.781,5.333 1.344,0.583 10 false FRONT SEAT SIDE AIRBAG ASSEMBLY (LH or RH)* 0.677,1.604 1.573,1.813 0.896,0.208 10 false Side Collision 1.979,1.604 2.469,1.813 0.49,0.208 10 false Impact 3.365,1.917 4.979,2.313 1.615,0.396 10 false REAR AIRBAG SENSOR (LH or RH)* 5.438,6.542 6.781,7.083 1.344,0.542 10 false CURTAIN SHIELD AIRBAG ASSEMBLY (LH or RH)*

*: The sensor on the collision side detects an impact and causes the airbags on that side to deploy.



iii.

For a rear side collision, if the floor side airbag sensor and the rear airbag sensor detect an impact, it informs the center airbag sensor assembly. The center airbag sensor assembly causes the curtain shield airbag assembly to deploy.

Y104859E04
0.167,4.875 2.51,5.063 2.344,0.188 10 false COMBINATION METER ASSEMBLY 0.531,5.417 2.042,5.583 1.51,0.167 10 false SRS WARNING LIGHT 1.125,6.188 1.458,6.375 0.333,0.188 10 false ECM 2.594,6.51 3.594,6.667 1,0.156 10 false CAN (V Bus) 3.99,4.833 4.771,5.552 0.781,0.719 10 false CENTER AIRBAG SENSOR ASSEMBLY 3.677,0.458 5.094,0.792 1.417,0.333 10 false FLOOR SIDE AIRBAG SENSOR 0.469,1.646 1.729,1.854 1.26,0.208 10 false Side Rear Collision 1.979,1.646 2.469,1.854 0.49,0.208 10 false Impact 3.375,1.927 5,2.26 1.625,0.333 10 false REAR AIRBAG SENSOR (RH or LH)* 5.438,5.646 6.781,6.219 1.344,0.573 10 false CURTAIN SHIELD AIRBAG ASSEMBLY (LH or RH)*

*: The sensor on the collision side detects an impact and causes the airbag on that side to deploy.





CONSTRUCTION


a.

Center Airbag Sensor Assembly

i.

The center airbag sensor assembly consists of a deceleration sensor, safing sensor, roll rate sensor, ignition control circuit, backup power source, diagnostic circuit and memory circuit.

Item Outline
Deceleration Sensor Deceleration sensors are built into the center airbag sensor assembly, front airbag sensors, side airbag sensor assemblies, rear airbag sensors and floor side airbag sensor. These sensors distort in the event of a collision. The amount of distortion is based on the deceleration rate of the vehicle during a frontal, side or side rear collision and is converted into an electric signal.
Ignition Control Circuit The ignition control circuit performs calculations based on the signal output from the deceleration sensors of the center airbag sensor assembly, front airbag sensors, side airbag sensor assemblies, rear airbag sensors and floor side airbag sensor. If the calculated values are greater than the specified values, the airbags are deployed.
Safing Sensor During a frontal, side or side rear collision, this sensor turns on and outputs an on signal to the center airbag sensor assembly if a deceleration rate of the safing sensor is greater than a specified value.
Backup Power Circuit The backup power circuit consists of a power supply capacitor and a DC-DC converter. When the power supply to the center airbag sensor assembly is disrupted during a collision, the power supply capacitor discharges and supplies electric power to the system. The DC-DC converter operates as a boosting transformer when the battery voltage falls below a predetermined level.
Diagnostic Circuit The diagnostic circuit constantly monitors for system malfunctions. When a malfunction is detected, it turns on the SRS warning light in the combination meter assembly to inform the driver.
Memory Circuit When a malfunction is detected by the diagnostic circuit, a code is stored in memory.



b.

Steering Pad

i.

The steering pad contains the driver airbag assembly.


ii.

The driver airbag assembly consists of an inflator and a bag.

V100414E02
4.156,1.729 5.01,1.729 true 2.073,2.135 3.208,2.135 true 1.854,2.031 2.146,2.344 0.292,0.313 10 false *1 5.073,1.625 5.625,1.938 0.552,0.313 10 false *2

Text in Illustration
*1 Bag *2 Inflator



c.

Front Passenger Airbag Assembly

i.

The front passenger airbag assembly is located in the upper section of the instrument panel of the front passenger seat.


ii.

The front passenger airbag assembly consists of an inflator and a bag.

V100415E02
3.656,2.51 3.656,3.323 true 4.219,1.01 4.219,0.417 4.219,0.417 4.406,0.417 true 4.458,0.313 4.75,0.625 0.292,0.313 10 false *1 3.615,3.323 3.823,3.563 0.208,0.24 10 false *2

Text in Illustration
*1 Bag *2 Inflator



d.

Front Seat Side Airbag Assembly

i.

Each front seat side airbag assembly is a one-piece design, consisting of an inflator and bag.

V100417E02
6.167,1.802 6.167,0.979 6.167,0.979 6.344,0.979 true 6.104,2.115 6.531,2.115 true 4.313,2.302 4.74,2.302 true 2.406,1.719 2.594,1.896 0.188,0.177 10 false A 1.688,2.969 1.875,3.146 0.188,0.177 10 false A 4.156,3.375 4.406,3.688 0.25,0.313 10 false *a 6.583,2.01 6.875,2.323 0.292,0.313 10 false *1 6.375,0.875 6.927,1.188 0.552,0.313 10 false *2 6.042,2.573 6.229,2.885 0.188,0.313 10 false *b 2.385,2.458 2.573,2.635 0.188,0.177 10 false B 1.583,2.083 1.771,2.26 0.188,0.177 10 false B 4.781,2.198 5.333,2.51 0.552,0.313 10 false *2

Text in Illustration
*1 Bag *2 Inflator
*a A-A Cross Section *b B-B Cross Section



e.

Curtain Shield Airbag Assembly

i.

Each curtain shield airbag assembly is a one-piece design, consisting of an inflator and bag.

V100418E02
4.292,0.875 4.292,0.271 4.292,0.271 4.469,0.271 true 2.885,0.875 2.885,0.271 2.885,0.271 2.708,0.271 true 3.438,0.281 3.625,0.458 0.188,0.177 10 false A 3.448,1.156 3.635,1.333 0.188,0.177 10 false A 1.333,4.552 1.542,4.865 0.208,0.313 10 false *a 2.5,0.167 2.792,0.479 0.292,0.313 10 false *1 4.51,0.167 5.063,0.479 0.552,0.313 10 false *2

Text in Illustration
*1 Bag *2 Inflator
*a A-A Cross Section - -



f.

Front Seat Inner Belt Assembly (Seat Belt Buckle Switch)

i.

A non-contact type switch is built into the front seat inner belt assembly (seat belt buckle switch) on the driver side.


ii.

The non-contact type switch contains a Hall IC and magnet.


iii.

The ejector inside the front seat inner belt assembly (seat belt buckle switch) and the plate installed to the ejector move when the seat belt is removed or inserted. The movement of the plate changes the magnetic flux density of the magnet.


iv.

The Hall IC detects changes in the magnetic flux density. These changes indicate that the seat belt is either fastened or unfastened, and the Hall IC outputs a signal to the center airbag sensor assembly (for driver).

Y100045E11
5.135,0.885 5.344,0.885 true 4.99,1.115 4.646,1.115 true 4.865,3.208 4.865,3.438 true 1.917,2.177 1.406,2.177 true 1.927,2.813 1.417,2.813 true 2.042,2.49 1.406,2.49 true 0.927,2.063 1.396,2.333 0.469,0.271 10 false Ejector 0.938,2.385 1.406,2.667 0.469,0.281 10 false Hall IC 0.917,2.708 1.458,3.01 0.542,0.302 10 false Magnet 4.188,1.01 4.667,1.333 0.479,0.323 10 false Hall IC 4.052,1.625 4.563,1.99 0.51,0.365 10 false Magnet 4.458,3.438 5.458,3.76 1,0.323 10 false Magnetic Flux 5.385,0.781 5.854,1.031 0.469,0.25 10 false Plate 5.333,1.479 6.844,1.927 1.51,0.448 10 false Seat belt not fastened 5.302,2.865 6.583,3.25 1.281,0.385 10 false Seat belt fastened




DIAGNOSIS


a.

If the center airbag sensor assembly detects a malfunction in the SRS airbag system, the center airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.


b.

The center airbag sensor assembly outputs the malfunction data, 5-digit Diagnostic Trouble Codes (DTCs), to the Techstream.


c.

The 5-digit DTCs can be read after connecting the Techstream to the DLC3. For details, refer to the Repair Manual.


d.

If the SRS airbag deploys, the center airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the center airbag sensor assembly with a new one.