Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
NM1440E _58 Vehicle Interior _056109 SUPPLEMENTAL RESTRAINT SYSTEMS _0273735 AIRBAG SYSTEM UN GENERAL/CONTROL/DETAILS F

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components have the following functions:

Component Function
Airbag Sensor Assembly
·

The airbag sensor assembly receives signals from the deceleration sensor and safing sensor built into the airbag sensor assembly and one of the front airbag sensors, determines whether the steering pad, instrument panel passenger without door airbag assembly and front seat belt pretensioners should be activated. It also diagnoses system malfunctions.

·

The airbag sensor assembly receives signals from the safing sensor built into the airbag sensor assembly, side airbag sensors and rear floor side airbag sensor, and determines whether the front seat airbag and curtain shield airbag should be activated. It also diagnoses system malfunctions.

·

The airbag sensor assembly sends an airbag deployment signal to the ECM through the Controller Area Network (CAN) to operate the fuel pump control.


Steering Pad The airbag assemblies are used as supplements to the seat belts to help reduce impact to the occupants.
Instrument Panel Passenger without Door Airbag Assembly
Front Seat Airbag Assembly LH/RH
Curtain Shield Airbag Assembly LH/RH
Front Airbag Sensor LH/RH Based on the deceleration of the vehicle during a frontal collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.
Side Airbag Sensor Assembly LH/RH Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.
Rear Airbag Sensor LH/RH
Rear Floor Side Airbag Sensor The seat position sensor detects the slide position of the driver seat.
Front Seat Outer Belt Assembly Driver The front seat outer belt assemblies are used as supplements to help to reduce the impacts to the occupants.
Front Seat Inner Belt Assembly Driver Seat Belt Buckle Switch The driver seat belt buckle switch detects if the driver seat belt is fastened.
Combination Meter Assembly SRS Warning Light The SRS warning light turns to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system.



OPERATING CONDITION


a.

If the impact of a collision is greater than the specified value, the SRS is activated automatically. The airbag sensor assembly include the safing sensor and deceleration sensor. The safing sensor is designed to turn on at a lower deceleration rate than the deceleration sensor.

i.

In case of a frontal collision, the airbag sensor assembly determines whether airbag deployment or pretensioner activation is necessary based on signals from the deceleration sensor and the front airbag sensor. If the safing sensor turns on simultaneously, current flows to the squibs to deploy the SRS components as shown in the illustration below.


ii.

However, a deployment ignition signal may be output with the deceleration sensor on signal even without a signal from a front airbag sensor.

V115172E02
0.354,1.885 2.104,2.26 1.75,0.375 10 false Deceleration Sensor On 0.458,2.708 2.021,3.083 1.563,0.375 10 false Safing Sensor On 3.104,2.323 3.542,2.688 0.438,0.365 10 false AND 0.417,3.417 2.146,3.792 1.729,0.375 10 false Airbag Sensor Assembly 0.417,0.51 2.063,0.917 1.646,0.406 10 false Front Airbag Sensor 4.49,0.323 6.656,0.698 2.167,0.375 10 false Steering Pad (Driver Side Squib) 4.521,3.99 6.594,4.385 2.073,0.396 10 false Front Seat Outer Belt Assembly 4.563,1.083 6.427,1.865 1.865,0.781 10 false Instrument Panel Passenger without Door Airbag Assembly 4.625,2.365 6.5,2.76 1.875,0.396 10 false Front Seat Airbag Assembly 4.5,3.198 6.573,3.594 2.073,0.396 10 false Curtain Shield Airbag Assembly


iii.

In case of a side collision, the airbag sensor assembly determines whether airbag deployment is necessary based on signals from the side airbag sensor assembly and safing sensor. If the safing sensor and side airbag sensor assembly turn on simultaneously, current flows to the squibs to deploy the SRS components shown in the illustration below.

V100406E06
5.094,1.052 6.219,1.75 1.125,0.698 10 false Front Seat Airbag Assembly 5.021,2.083 6.365,2.792 1.344,0.708 10 false Curtain Shield Airbag Assembly 3.938,1.76 4.354,2.125 0.417,0.365 10 false AND 0.854,0.521 2.01,0.865 1.156,0.344 10 false Safing Sensor On 0.51,2.74 2.479,3.198 1.969,0.458 10 false Side Airbag Sensor Assembly 0.333,1.156 2.375,1.938 2.042,0.781 10 false Airbag Sensor Assembly or Rear Floor Side Airbag Sensor


iv.

In case of a rear side collision, the airbag sensor assembly determines whether airbag deployment is necessary based on signals from the rear airbag sensor and safing sensor. If the safing sensor and rear airbag sensor turn on simultaneously, current flows to the squibs to deploy the SRS components shown in the illustration below.

V100407E05
0.719,0.531 1.875,0.875 1.156,0.344 10 false Safing Sensor On 0.656,2.75 2.458,3.417 1.802,0.667 10 false Rear Airbag Sensor 0.219,1.167 2.302,1.948 2.083,0.781 10 false Airbag Sensor Assembly or Rear Floor Side Airbag Sensor 4.729,1.698 6.854,2.24 2.125,0.542 10 false Curtain Shield Airbag Assembly 3.792,1.75 4.208,2.115 0.417,0.365 10 false AND




SYSTEM CONTROL


a.

Airbag for Frontal Collision

i.

There are 6 airbags which deploy in the event of a frontal collision: the steering pad, instrument panel passenger without door airbag assembly assembly, front seat airbag assemblies and curtain shield airbag assemblies. These airbags deploy simultaneously. The steering pad and instrument panel passenger without door airbag assembly assembly use dual-stage control.


ii.

The airbag sensor assembly detects the information indicated below from various sources in order to activate the dual-stage control.


iii.

For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag sensor assembly. The airbag sensor assembly causes the steering pad, instrument panel passenger without door airbag assembly assembly, front seat airbag assemblies and curtain shield airbag assemblies to deploy. Meanwhile, the airbag sensor assembly activates the seat belt pretensioners for the driver, front passenger.

Airbag Information Source
Driver Extent of Impact
·

Front Airbag Sensor (RH or LH)

·

Airbag Sensor Assembly


Seat Belt Condition Front Seat Inner Belt Assembly (Buckle Switch) (Non-contact Type)
Front Passenger Extent of Impact
·

Front Airbag Sensor (RH or LH)

·

Airbag Sensor Assembly



V115177E02
0.552,4.823 2.458,5.156 1.906,0.333 10 false Combination Meter Assembly 0.844,5.427 2.354,5.74 1.51,0.313 10 false SRS Warning Light 1.365,6.146 1.854,6.448 0.49,0.302 10 false ECM 2.688,6.49 3.51,6.802 0.823,0.313 10 false CAN (V Bus) 1.083,1.167 1.688,1.375 0.604,0.208 10 false Collision 1.948,1.167 2.438,1.375 0.49,0.208 10 false Impact 5.594,1.167 6.75,1.802 1.156,0.635 10 false Steering Pad (Driver Side Squib) 5.594,6.792 6.979,7.74 1.385,0.948 10 false Instrument Panel Passenger without Door Airbag Assembly 5.583,2.802 6.938,3.542 1.354,0.74 10 false Front Seat Outer Belt Assembly LH 3.292,0.26 5.26,0.573 1.969,0.313 10 false Front Airbag Sensor LH or RH 0.438,2.719 2.771,3.24 2.333,0.521 10 false Front Seat Inner Belt Assembly LH 3.823,3.302 4.458,4.854 0.635,1.552 10 false Airbag Sensor Assembly 5.594,6 6.708,6.656 1.115,0.656 10 false Front Seat Airbag Assembly LH 5.594,5.198 6.719,5.875 1.125,0.677 10 false Front Seat Airbag Assembly RH 5.594,3.594 6.927,4.313 1.333,0.719 10 false Curtain Shield Airbag Assembly RH 5.594,4.396 6.927,5.073 1.333,0.677 10 false Curtain Shield Airbag Assembly LH 5.583,2.042 6.927,2.781 1.344,0.74 10 false Front Seat Outer Belt Assembly RH



b.

Airbag for Side/Side Rear Collision

i.

There are 4 airbags which deploy in the event of a severe side collision: the front seat airbag assemblies and curtain shield airbag assemblies. These airbags deploy simultaneously.


ii.

For a side collision, if the side airbag sensor assembly detects an impact, it informs the airbag sensor assembly, and the airbag sensor assembly causes the front seat and curtain shield airbag assemblies to deploy simultaneously.

Y104858E06
1.125,6.052 1.458,6.24 0.333,0.188 10 false ECM 2.594,6.396 3.594,6.552 1,0.156 10 false CAN (V Bus) 0.677,1.604 1.573,1.813 0.896,0.208 10 false Side Collision 1.979,1.604 2.469,1.813 0.49,0.208 10 false Impact 0.375,4.677 2.344,5.031 1.969,0.354 10 false Combination Meter Assembly 0.604,5.292 2.115,5.552 1.51,0.26 10 false SRS Warning Light 4,4.375 4.635,5.208 0.635,0.833 10 false Airbag Sensor Assembly 3.375,1.938 5.365,2.292 1.99,0.354 10 false Rear Airbag Sensor (RH or LH)* 3.427,0.438 5.313,1.083 1.885,0.646 10 false Side Airbag Sensor Assembly (RH or LH)* 5.344,4.75 6.719,5.396 1.375,0.646 10 false Front Seat Airbag Assembly (RH or LH)* 5.375,6.563 6.75,7.271 1.375,0.708 10 false Curtain Shield Airbag Assembly (RH or LH)* 0.25,7.438 6.781,7.74 6.531,0.302 10 false *: The sensor on the collision side detects an impact and causes the airbags on that side to deploy


iii.

For a rear side collision, if the rear floor side airbag sensor and the rear airbag sensor detect an impact, it informs the airbag sensor assembly. The airbag sensor assembly causes the curtain shield airbag assembly to deploy.

Y104859E05
1.135,6.146 1.469,6.333 0.333,0.188 10 false ECM 2.594,6.458 3.594,6.76 1,0.302 10 false CAN (V Bus) 0.469,1.604 1.729,1.813 1.26,0.208 10 false Side Rear Collision 1.979,1.604 2.469,1.813 0.49,0.208 10 false Impact 0.396,4.781 2.729,5.135 2.333,0.354 10 false Combination Meter Assembly 0.667,5.344 2.177,5.604 1.51,0.26 10 false SRS Warning Light 4,4.885 4.635,5.667 0.635,0.781 10 false Airbag Sensor Assembly 3.375,0.49 5.313,0.917 1.938,0.427 10 false Rear Floor Side Airbag Sensor 5.344,5.573 6.708,6.177 1.365,0.604 10 false Curtain Shield Airbag Assembly (RH or LH)* 3.365,1.979 5.531,2.406 2.167,0.427 10 false Rear Airbag Sensor (RH or LH)* 0.146,7.448 6.313,7.833 6.167,0.385 10 false *: The sensor on the collision side detects an impact and causes the airbag on that side to deploy.




CONSTRUCTION


a.

Airbag Sensor Assembly

i.

The airbag sensor assembly consists of a deceleration sensor, safing sensor, roll rate sensor, ignition control circuit, backup power source, diagnostic circuit and memory circuit.

Item Outline
Deceleration Sensor Deceleration sensors are built into the airbag sensor assembly, front airbag sensors, side airbag sensor assemblies, rear airbag sensors and rear floor side airbag sensor. These sensors distort in the event of a collision. The amount of distortion is based on the deceleration rate of the vehicle during a frontal, side or side rear collision and is converted into an electric signal.
Ignition Control Circuit The ignition control circuit performs calculations based on the signal output from the deceleration sensors of the airbag sensor assembly, front airbag sensors, side airbag sensor assemblies, rear airbag sensors and rear floor side airbag sensor. If the calculated values are greater than the specified values, the airbags are deployed.
Safing Sensor During a frontal, side or side rear collision, this sensor turns on and outputs an on signal to the airbag sensor assembly if a deceleration rate of the safing sensor is greater than a specified value.
Backup Power Circuit The backup power circuit consists of a power supply capacitor and a DC - DC converter. When the power supply to the airbag sensor assembly is disrupted during a collision, the power supply capacitor discharges and supplies electric power to the system. The DC - DC converter operates as a boosting transformer when the battery voltage falls below a predetermined level.
Diagnostic Circuit The diagnostic circuit constantly monitors for system malfunctions. When a malfunction is detected, it turns on the SRS warning light in the combination meter assembly to inform the driver.
Memory Circuit When a malfunction is detected by the diagnostic circuit, a code is stored in memory.



b.

Steering Pad

i.

The steering pad contains the driver airbag assembly.


ii.

The driver airbag assembly consists of an inflator and a bag.

V100414E02
4.156,1.729 5.01,1.729 true 2.073,2.135 3.208,2.135 true 1.854,2.031 2.146,2.344 0.292,0.313 10 false *1 5.073,1.625 5.625,1.938 0.552,0.313 10 false *2

Text in Illustration
*1 Bag *2 Inflator



c.

Instrument Panel Passenger without Door Airbag Assembly

i.

The instrument panel passenger without door airbag assembly assembly is located in the upper section of the instrument panel of the front passenger seat.


ii.

The instrument panel passenger without door airbag assembly assembly consists of an inflator and a bag.

V100415E02
3.656,2.51 3.656,3.323 true 4.219,1.01 4.219,0.417 4.219,0.417 4.406,0.417 true 4.458,0.313 4.75,0.625 0.292,0.313 10 false *1 3.615,3.323 3.823,3.563 0.208,0.24 10 false *2

Text in Illustration
*1 Bag *2 Inflator



d.

Front Seat Airbag Assembly

i.

Each front seat airbag assembly is a one-piece design, consisting of an inflator and bag.

V105160E02
6.177,1.813 6.177,0.99 6.177,0.99 6.354,0.99 true 6.115,2.125 6.542,2.125 true 4.323,2.281 4.75,2.281 true 2.417,1.646 2.604,1.823 0.188,0.177 10 false A 1.625,2.948 1.813,3.125 0.188,0.177 10 false A 4.167,3.354 4.417,3.667 0.25,0.313 10 false *a 6.594,2.021 6.885,2.333 0.292,0.313 10 false *1 6.385,0.885 6.927,1.198 0.542,0.313 10 false *2 6.063,2.594 6.25,2.906 0.188,0.313 10 false *b 2.333,2.375 2.521,2.552 0.188,0.177 10 false B 1.594,2.052 1.781,2.229 0.188,0.177 10 false B 4.792,2.177 5.333,2.49 0.542,0.313 10 false *2

Text in Illustration
*1 Bag *2 Inflator
*a A - A Cross Section *b B - B Cross Section



e.

Curtain Shield Airbag Assembly

i.

Each curtain shield airbag assembly is a one-piece design, consisting of an inflator and bag.

V105153E05
4.281,0.865 4.281,0.271 4.281,0.271 4.458,0.271 true 2.875,0.865 2.875,0.271 2.875,0.271 2.708,0.271 true 3.438,0.354 3.625,0.531 0.188,0.177 10 false A 3.438,1.063 3.625,1.24 0.188,0.177 10 false A 1.323,4.594 1.531,4.906 0.208,0.313 10 false *a 2.51,0.167 2.802,0.479 0.292,0.313 10 false *1 4.5,0.167 5.042,0.479 0.542,0.313 10 false *2

Text in Illustration
*1 Bag *2 Inflator
*a A - A Cross Section - -



f.

Front Seat Inner Belt Assembly (Buckle Switch)

i.

A non-contact type switch is built into the front seat inner belt assembly (buckle switch) on the driver side.


ii.

The non-contact type switch contains a Hall IC and magnet.


iii.

The ejector inside the front seat inner belt assembly (buckle switch) and the plate installed to the ejector move when the seat belt is removed or inserted. The movement of the plate changes the magnetic flux density of the magnet.


iv.

The Hall IC detects changes in the magnetic flux density. These changes indicate that the seat belt is either fastened or unfastened, and the Hall IC outputs a signal to the airbag sensor assembly (for driver).

Y100045E11
5.135,0.885 5.344,0.885 true 4.99,1.115 4.646,1.115 true 4.865,3.208 4.865,3.438 true 1.917,2.177 1.406,2.177 true 1.927,2.813 1.417,2.813 true 2.042,2.49 1.406,2.49 true 0.927,2.063 1.396,2.333 0.469,0.271 10 false Ejector 0.938,2.385 1.406,2.667 0.469,0.281 10 false Hall IC 0.917,2.708 1.458,3.01 0.542,0.302 10 false Magnet 4.188,1.01 4.667,1.333 0.479,0.323 10 false Hall IC 4.052,1.625 4.563,1.99 0.51,0.365 10 false Magnet 4.458,3.438 5.458,3.76 1,0.323 10 false Magnetic Flux 5.385,0.781 5.854,1.031 0.469,0.25 10 false Plate 5.333,1.479 6.844,1.927 1.51,0.448 10 false Seat belt not fastened 5.302,2.865 6.583,3.25 1.281,0.385 10 false Seat belt fastened




DIAGNOSIS


a.

If the airbag sensor assembly detects a malfunction in the SRS airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.


b.

The airbag sensor assembly outputs the malfunction data, 5-digit Diagnostic Trouble Codes (DTCs), to the Techstream.


c.

The 5-digit DTCs can be read after connecting the Techstream to the DLC3. For details, refer to the Repair Manual.


d.

If the SRS airbag deploys, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.