SYSTEM CONTROL
The sliding roof system has following functions:
| Function | Outline | Customizable* |
|---|---|---|
| Manual Open-and-close | This function opens or closes the sliding roof while the open switch or close switch is pressed for 0.3 seconds or less. The sliding roof stops as soon as the switch is released. | Standard
(Not Customizable) |
| One-touch Auto Open-and-close | This function fully opens or closes the sliding roof when open switch or close switch is pressed for 0.3 seconds or more. | Standard
(Not Customizable) |
| Manual Tilt Up-and-down | This function tilts up or down the sliding roof while the up switch or down switch is pressed for 0.3 seconds or less. The sliding roof stops as soon as the switch is released. | Standard
(Not Customizable) |
| One-touch Auto Tilt Up-and-down | This function fully tilts up or down the sliding roof when the up switch or down switch is pressed for 0.3 seconds or more. | Standard
(Not Customizable) |
| Jam Protection | The jam protection function automatically stops the sliding roof and moves it open half way (or to the fully tilted up position) if a foreign object gets jammed in the sliding roof during close or tilt down operation. | Standard
(Not Customizable) |
| Key-off Operation | The key-off operation function makes it possible to operate the sliding roof for approximately 43 seconds after the ignition switch is turned to on (ACC) or off, if the front door is not opened. | Standard
(Not Customizable) |
| Mechanical Key-linked Open-and-close | ·
When the key cylinder in the driver door is turned and held in the unlock position for 1.5 seconds or more, the sliding roof drive gear sub-assembly (sliding roof ECU) activates the sliding roof motor to open the sliding roof while the key cylinder is turned. ·
Similarly, turning and holding the driver door key cylinder in the lock position will cause the sliding roof to close. |
Default setting is off |
| Mechanical Key-linked Tilt up-and-down | ·
When the key cylinder in the driver door is turned and held in the unlock position for 1.5 seconds or more, the sliding roof drive gear sub-assembly (sliding roof ECU) activates the sliding roof motor to tilt up the sliding roof while the key cylinder is turned. ·
Similarly, turning and holding the driver door key cylinder in the lock position will cause the sliding roof to tilt down. |
Default setting is off |
| Transmitter-linked Open-and-close | ·
When the main body ECU (multiplex network body ECU) receives an unlock signal from the key continuously for 2.5 seconds or more via the door control receiver, the sliding roof drive gear sub-assembly (sliding roof ECU) opens the sliding roof. ·
Similarly, the main body ECU (multiplex network body ECU) receives an lock signal from the key continuously via the door control receiver, the sliding roof drive gear sub-assembly (sliding roof ECU) closes the sliding roof. |
Default setting is off |
| Transmitter-linked Tilt Up-and-down | ·
When the main body ECU (multiplex network body ECU) receives an unlock signal from the key continuously for 2.5 seconds or more via the door control receiver, the sliding roof drive gear sub-assembly (sliding roof ECU) tilt up the sliding roof. ·
Similarly, the main body ECU (multiplex network body ECU) receives an lock signal from the key continuously via the door control receiver, the sliding roof drive gear sub-assembly (sliding roof ECU) tilt down the sliding roof. |
Default setting is off |
| Sliding Roof Open Warning | When the ignition switch is turned from on (IG) to off and the driver door is opened with the sliding roof open, the buzzer in the combination meter assembly sounds once. | Standard
(Not Customizable) |
*: The customizable functions can be turned on or off using the customized body electronics system. For details, refer to the 4RUNNER Repair Manual (Pub. No. RM1440E).
The sliding roof ECU memorizes the initial position of the sliding roof. This memory is not cleared if the battery terminals are disconnected. However, initialization is necessary after the sliding roof drive gear sub-assembly is replaced.
After replacing the sliding roof drive gear sub-assembly, the sliding roof will not operate correctly. In this case, the sliding roof position must be initialized as described below:
Keep pressing the slide roof switch (up) or (close) until initialization completes. This will enable the sliding roof ECU to start initializing and perform the tilt-up and tilt-down operations of the sliding roof in sequence.
Keep the switch pressed for 1 second after the tilt-up operation is completed.
The sliding roof ECU performs the tilt down operation.
The initialization process ends when the close operation is completed.
Keep the tilt-up or slide close switch pressed during initialization. If the tilt up or close switch is released during initialization, the system will not be able to complete initialization. If this occurs, the aforementioned steps must be performed again.
For details, refer to the 4RUNNER Repair Manual (Pub. No. RM1440E).
Jam Protection Function
To control the jam protection function, the sliding roof ECU monitors the amount of movement and judges jamming of the sliding roof based on the pulse signals from Hall IC1, and the movement direction of the sliding roof from the phase difference between the pulses from Hall IC1 and Hall IC2.