RM1440E
_V1
General
_056122
SPECIFICATIONS
_0273848
1GR-FE ENGINE CONTROL
F
SPECIFICATIONS 1GR-FE ENGINE CONTROL SERVICE DATA
- Camshaft Timing Oil Control Valve:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
20°C (68°F)
|
6.9 to 7.9 Ω
|
- Crankshaft Position Sensor:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
Cold
|
1630 to 2740 Ω
|
| Hot
|
2065 to 3225 Ω
|
- Engine Coolant Temperature Sensor:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
Approx. 20°C (68°F)
|
2.32 to 2.59 kΩ
|
| Approx. 80°C (176°F)
|
0.310 to 0.326 kΩ
|
- Throttle Body:
| Tester Connection
|
Condition
|
Specified Condition
|
| 2 (M+) - 1 (M-)
|
20°C (68°F)
|
0.3 to 100 Ω
|
- Knock Sensor:
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
20°C (68°F)
|
120 to 280 kΩ
|
- Accelerator Pedal:
| Accelerator Pedal Operation
|
Accelerator Position No. 1
|
Accelerator Position No. 2
|
| Released
|
0.5 to 1.1 V
|
1.2 to 2.0 V
|
| Depressed
|
2.6 to 4.5 V
|
3.4 to 4.7 V
|
- Air Fuel Ratio Sensor (for Bank 1):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HA1A) - 2 (+B)
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
| 1 (HA1A) - 4 (A1A-)
|
Always
|
10 kΩ or higher
|
- Air Fuel Ratio Sensor (for Bank 2):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HA2A) - 2 (+B)
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
| 1 (HA2A) - 4 (A2A-)
|
Always
|
10 kΩ or higher
|
- Heated Oxygen Sensor (for Bank 1):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HT1B) - 2 (+B)
|
20°C (68°F)
|
11 to 16 Ω
|
| 1 (HT1B) - 4 (E2)
|
Always
|
10 kΩ or higher
|
- Heated Oxygen Sensor (for Bank 2):
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HT2B) - 2 (+B)
|
20°C (68°F)
|
11 to 16 Ω
|
| 1 (HT2B) - 4 (E2)
|
Always
|
10 kΩ or higher
|
- Circuit Opening Relay:
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
- No. 1 Integration Relay (IG2):
| Tester Connection
|
Condition
|
Specified Condition
|
| IG2 fuse
|
Always
|
Below 1 Ω
|
| 1E-1 - 1C-4
|
Battery voltage not applied to terminals 1C- 1 and 1C-3
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1C-1 and 1C-3
|
Below 1 Ω
|
- No. 1 Integration Relay (EFI):
| Tester Connection
|
Condition
|
Specified Condition
|
| EFI fuse
|
Always
|
Below 1 Ω
|
| 1E-1 - 1D-4
|
Battery voltage not applied to terminals 1D- 2 and 1D-3
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1D-2 and 1D-3
|
Below 1 Ω
|
- No. 1 Integration Relay (A/F):
| Tester Connection
|
Condition
|
Specified Condition
|
| A/F fuse
|
Always
|
Below 1 Ω
|
| 1E-1 - 1D-8
|
Battery voltage not applied to terminals 1D- 4 and 1D-7
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1D-4 and 1D-7
|
Below 1 Ω
|
- Main Body ECU (Driver Side Junction Block) for ACC Relay:
| Tester Connection
|
Condition
|
Specified Condition
|
| 2B-17 - 2E-1
|
Battery voltage not applied to terminals 2C- 48 and 2B-4
|
10 kΩ or higher
|
| Battery voltage applied to terminals 2C-48 and 2B-4
|
Below 1 Ω
|
- Main Body ECU (Driver Side Junction Block) for IG1 No. 2 Relay:
| Tester Connection
|
Condition
|
Specified Condition
|
| 2C-31 - 2E-1
|
Battery voltage not applied to terminals 2C- 52 and 2B-4
|
10 kΩ or higher
|
| Battery voltage applied to terminals 2C-52 and 2B-4
|
Below 1 Ω
|
- Spark Plug:
| Recommended spark plug
|
Correct electrode gap for new spark plug
|
Maximum electrode gap for used spark plug
|
Standard insulation resistance
|
| SK20HR11 or SK16HR11
|
Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.)
|
1.3 mm (0.0512 in.)
|
10 MΩ or higher
|