Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › RELAY › 2009.08–2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273875 RELAY G

1GR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CIRCUIT OPENING RELAY (C/OPN)

a.
A184106E21
2.521,1.135 2.917,1.135 false 2.51,1.625 2.917,1.625 false 1.552,0.188 1.677,0.188 1.677,0.188 2.01,0.563 false 3.021,0.177 2.896,0.177 2.896,0.177 2.615,0.563 false 0.208,0.771 0.417,0.948 0.208,0.177 10 false 3 1.229,0.74 1.427,0.917 0.198,0.177 10 false 5 0.229,1.313 0.385,1.49 0.156,0.177 10 false 2 1.208,1.313 1.438,1.49 0.229,0.177 10 false 1 2.99,1.51 3.198,1.688 0.208,0.177 10 false 3 3.01,1.031 3.208,1.208 0.198,0.177 10 false 5 3.104,0.083 3.26,0.26 0.156,0.177 10 false 2 1.396,0.125 1.625,0.302 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the circuit opening relay.


Hide 82641 2.INSPECT NO. 1 INTEGRATION RELAY (IG2)

a.

Check the IG2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 fuse.



b.

Check the IG2 relay.

i.
U149611E02
2.417,1.604 2.646,1.781 0.229,0.177 10 false 1C 1.302,1.625 1.521,1.792 0.219,0.167 10 false 1D 0.406,1.615 0.625,1.792 0.219,0.177 10 false 1E 0.115,0.094 0.344,0.323 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - 1C-4 Battery voltage not applied to terminals 1C-1 and 1C-3 10 kΩ or higher
Battery voltage applied to terminals 1C-1 and 1C-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 82641 3.INSPECT NO. 1 INTEGRATION RELAY (EFI)

a.

Check the EFI fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω


If the result is not as specified, replace the EFI fuse.



b.

Check the EFI relay.

i.
U149611E02
2.417,1.604 2.646,1.781 0.229,0.177 10 false 1C 1.302,1.625 1.521,1.792 0.219,0.167 10 false 1D 0.406,1.615 0.625,1.792 0.219,0.177 10 false 1E 0.115,0.094 0.344,0.323 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - 1D-4 Battery voltage not applied to terminals 1D-2 and 1D-3 10 kΩ or higher
Battery voltage applied to terminals 1D-2 and 1D-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 82641 4.INSPECT NO. 1 INTEGRATION RELAY (A/F)

a.

Check the A/F fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω


If the result is not as specified, replace the A/F fuse.



b.
U149611E02
2.417,1.604 2.646,1.781 0.229,0.177 10 false 1C 1.302,1.625 1.521,1.792 0.219,0.167 10 false 1D 0.406,1.615 0.625,1.792 0.219,0.177 10 false 1E 0.115,0.094 0.344,0.323 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - 1D-8 Battery voltage not applied to terminals 1D-4 and 1D-7 10 kΩ or higher
Battery voltage applied to terminals 1D-4 and 1D-7 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.


Hide 5.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

NOTICE:

The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).


a.

Inspect the ACC relay.

i.

Measure the resistance according to the value(s) in the table below.

U149637E02
0.771,0.781 0.969,0.927 0.198,0.146 10 false 2E 0.104,0.063 0.302,0.208 0.198,0.146 10 false *a 2.75,0.781 2.948,0.927 0.198,0.146 10 false 2B 5.438,0.792 5.677,0.969 0.24,0.177 10 false 2C

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2B-17 - 2E-1 Battery voltage not applied to terminals 2C-48 and 2B-4 10 kΩ or higher
Battery voltage applied to terminals 2C-48 and 2B-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.



b.

Inspect the IG1 No. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

U149637E02
0.771,0.781 0.969,0.927 0.198,0.146 10 false 2E 0.104,0.063 0.302,0.208 0.198,0.146 10 false *a 2.75,0.781 2.948,0.927 0.198,0.146 10 false 2B 5.438,0.792 5.677,0.969 0.24,0.177 10 false 2C

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2C-31 - 2E-1 Battery voltage not applied to terminals 2C-52 and 2B-4 10 kΩ or higher
Battery voltage applied to terminals 2C-52 and 2B-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.