1.INSPECT CIRCUIT OPENING RELAY (C/OPN) (w/o Secondary Air Injection System)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the circuit opening relay.
82641
2.INSPECT NO. 1 INTEGRATION RELAY (IG2)
Check the IG2 fuse.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 fuse | Always | Below 1 Ω |
If the result is not as specified, replace the IG2 fuse.
Check the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1E-1 - 1C-4 | Battery voltage not applied to terminals 1C-1 and 1C-3 | 10 kΩ or higher |
| Battery voltage applied to terminals 1C-1 and 1C-3 | Below 1 Ω |
| *a | Component without harness connected
(Integration Relay) |
If the result is not as specified, replace the No. 1 integration relay.
82641
3.INSPECT NO. 1 INTEGRATION RELAY (EFI)
Check the EFI fuse.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI fuse | Always | Below 1 Ω |
If the result is not as specified, replace the EFI fuse.
Check the EFI relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1E-1 - 1D-4 | Battery voltage not applied to terminals 1D-2 and 1D-3 | 10 kΩ or higher |
| Battery voltage applied to terminals 1D-2 and 1D-3 | Below 1 Ω |
| *a | Component without harness connected
(Integration Relay) |
If the result is not as specified, replace the No. 1 integration relay.
82641
4.INSPECT NO. 1 INTEGRATION RELAY (A/F)
Check the A/F fuse.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A/F fuse | Always | Below 1 Ω |
If the result is not as specified, replace the A/F fuse.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1E-1 - 1D-8 | Battery voltage not applied to terminals 1D-4 and 1D-7 | 10 kΩ or higher |
| Battery voltage applied to terminals 1D-4 and 1D-7 | Below 1 Ω |
| *a | Component without harness connected
(Integration Relay) |
If the result is not as specified, replace the No. 1 integration relay.
5.INSPECT AIR PUMP HEATER RELAY (AIR PUMP HTR) (w/ Secondary Air Injection System)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the air pump heater relay.
6.INSPECT AIR INJECTION VSV RELAY (AI-VSV) (w/ Secondary Air Injection System)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the air injection VSV relay.
7.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)
The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).
Inspect the ACC relay.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Main Body ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-17 - 2E-1 | Battery voltage not applied to terminals 2C-48 and 2B-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 2C-48 and 2B-4 | Below 1 Ω |
If the result is not as specified, replace the main body ECU.
Inspect the IG1 No. 1 relay.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Main Body ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2C-31 - 2E-1 | Battery voltage not applied to terminals 2C-52 and 2B-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 2C-52 and 2B-4 | Below 1 Ω |
If the result is not as specified, replace the main body ECU.