Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0505  Idle Control System Malfunction  


DESCRIPTION

The idling speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) a one-valve-type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No. DTC Detection Condition Trouble Area
P0505 Idling speed continues to vary greatly from the target idling speed (2 trip detection logic).
·

ETCS (Electronic Throttle Control System)

·

Air induction system

·

PCV hose connections

·

ECM



MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following conditions are met:

·

The difference between the target engine idling speed and actual engine idling speed exceeds the threshold and the IAC flow rate learned value is stuck at the upper or lower limit for 5 seconds or more.

·

After driving at a vehicle speed of 10 km/h (6.25 mph) or more, the actual engine idling speed minus the target idling speed is less than -100 rpm or 150 rpm or more when the A/C and NSW are off, or less than -100 rpm or 200 rpm or more when the A/C and NSW are on 5 times or more during a driving cycle.


A121611E02
0.125,0.073 0.876,0.289 0.750,0.216 10 Example: 0.298,1.092 1.304,1.293 1.006,0.201 10 Idling Speed 1.953,2.059 3.136,2.260 1.184,0.201 10 Target Speed 2.853,3.645 3.336,3.846 0.484,0.201 10 Time 5.916,3.79 6.400,3.991 0.484,0.201 10 Time 3.936,3.216 4.420,3.417 0.484,0.201 10 Small 3.936,1.684 4.420,1.885 0.484,0.201 10 Large 3.628,1.092 5.556,1.293 1.928,0.201 10 Learned Idling Air Volume 5.926,1.425 6.759,1.626 0.834,0.201 10 Maximum 5.926,2.975 6.759,3.176 0.834,0.201 10 Minimum 4.216,2.497 4.395,2.698 0.178,0.201 10 0 1.895,2.992 3.457,3.193 1.561,0.201 10 Actual Idling Speed

CONFIRMATION DRIVING PATTERN

A231468E06
0.606,1.193 1.876,1.395 1.27,0.203 10 10 km/h (6.25 mph) 1.412,2.029 1.828,2.19 0.416,0.161 10 Idling 0.648,2.379 1.862,2.739 1.213,0.36 10 Ignition Switch ON 2.356,2.536 2.549,2.724 0.193,0.189 10 [A] 2.75,2.239 2.965,2.395 0.214,0.156 10 [B] 6.306,3.309 6.527,3.483 0.221,0.175 10 [F] 2.313,3.523 3.559,3.68 1.246,0.156 10 5 minutes or more 4.607,3.385 5.914,3.541 1.307,0.156 10 20 seconds or more 4.557,2.949 4.875,3.365 4.875,3.365 4.025,2.949 false 5.744,2.949 5.104,3.337 5.104,3.337 5.127,2.949 false 3.616,0.976 3.865,1.169 0.249,0.193 10 [E] 5.929,0.963 6.178,1.157 0.249,0.193 10 [E] 5.35,0.967 5.598,1.16 0.249,0.193 10 [E] 4.776,0.969 5.025,1.162 0.249,0.193 10 [E] 4.203,0.974 4.452,1.167 0.249,0.193 10 [E] 3.121,2.244 3.342,2.419 0.221,0.175 10 [C] 1.829,3.15 2.62,3.315 0.791,0.166 10 Warming up 3.322,3.309 3.543,3.483 0.221,0.175 10 [D] 2.838,2.958 2.614,3.229 false 3.184,2.949 2.576,3.514 false

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

Idle the engine for 5 minutes or more [C].

HINT:

In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0505.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].



13.

Accelerate the vehicle to 10 km/h (6.25 mph) or more, and then idle the engine for 20 seconds or more [E].

14.

Repeat step [E] 5 times.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

16.

Read pending DTCs.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P0505.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

The following conditions may also cause DTC P0505 to be stored:

1.

The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.

2.

The accelerator pedal being not fully released.


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Engine Speed, ISC Feedback Value and ISC Learning Value] (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


e.

Read DTCs.

Result
Display (DTC Output) Proceed to
DTC P0505 is output A
DTC P0505 and other DTCs are output B

HINT:

If any DTCs other than P0505 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.


OK:

PCV hose is connected correctly and is not damaged.



OK

3.CHECK INTAKE SYSTEM

NG

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leakage.

OK:

No leakage in intake system.




OK

4.CHECK THROTTLE VALVE

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.CHECK THROTTLE VALVE
a.

Check the throttle valve condition.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.




OK

5.CONFIRM WHETHER DTC OUTPUT RECURS

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

5.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


e.

Read DTCs.

Result
Display (DTC Output) Proceed to
DTC P0505 is output A
No DTC is output B



A

B

END