Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2009.08–2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


CHECK ECM


U149626E03
0.625,0.521 0.896,0.677 0.271,0.156 10 false F51 1.667,0.521 1.938,0.677 0.271,0.156 10 false F50 3.135,0.521 3.406,0.677 0.271,0.156 10 false B36 4.177,0.51 4.448,0.667 0.271,0.156 10 false B37 5.24,0.51 5.51,0.667 0.271,0.156 10 false B38 6.281,0.521 6.552,0.677 0.271,0.156 10 false B39

a.

Measure the voltage of the ECM connectors.

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F51-24 (BATT) - B38-12 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
B38-23 (+BM) - B38-12 (E1) P-L - BR Power source of throttle actuator Always 11 to 14 V
F50-21 (IGSW) - B38-12 (E1) W - BR Ignition switch Ignition switch ON 11 to 14 V
F51-22 (+B) - B38-12 (E1) W - BR Power source of ECM Ignition switch ON 11 to 14 V
F51-23 (+B2) - B38-12 (E1) W - BR Power source of ECM Ignition switch ON 11 to 14 V
B37-19 (OC1+) - B37-20 (OC1-) R-W - GR Camshaft timing oil control valve (for intake side of bank 1) Ignition switch ON Pulse generation (see waveform 1)
B36-19 (OC2+) - B36-20 (OC2-) B-R - L-R Camshaft timing oil control valve (for intake side of bank 2) Ignition switch ON Pulse generation
(see waveform 1)
B37-21 (OE1+) - B37-22 (OE1-) G-B - B-R Camshaft timing oil control valve (for exhaust side of bank 1) Ignition switch ON Pulse generation
(see waveform 1)
B36-21 (OE2+) - B36-22 (OE2-) W-G - L Camshaft timing oil control valve (for exhaust side of bank 2) Ignition switch ON Pulse generation
(see waveform 1)
F51-9 (MREL) - B38-12 (E1) V - BR EFI MAIN relay Ignition switch ON 11 to 14 V
B37-14 (VG) - B37-13 (E2G) L-W - B-W Mass air flow meter Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
B37-15 (THA) - B37-7 (ETHA) Y - G Intake air temperature sensor Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
B38-17 (THW) - B37-8 (ETHW) G - W-R Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
B38-13 (VCTA) - B38-14 (ETA) R - W Power source for throttle position sensor (fixed voltage) Ignition switch ON 4.5 to 5.5 V
B38-15 (VTA1) - B38-14 (ETA) LG - W Throttle position sensor (for engine control) Ignition switch ON,
throttle valve fully closed
0.5 to 1.1 V
Ignition switch ON,
throttle valve fully open
3.3 to 4.9 V
B38-16 (VTA2) - B38-14 (ETA) G-W - W Throttle position sensor (for sensor malfunction detection) Ignition switch ON,
throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON,
throttle valve fully open
4.6 to 5.0 V
F50-6 (VPA) - F50-3 (EPA) L - P Accelerator pedal position sensor (for engine control) Ignition switch ON,
accelerator pedal released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
F50-5 (VPA2) - F50-1 (EPA2) GR - W Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON,
accelerator pedal released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 5.0 V
F50-4 (VCPA) - F50-3 (EPA) LG - P Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
F50-2 (VCP2) - F50-1 (EPA2) R - W Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
B39-17 (HA1A) - B39-16 (E04)
B39-19 (HA2A) - B39-16 (E04)
R-L - W-B
B-W - W-B
Air fuel ratio sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
B38-1 (A1A+) - B38-12 (E1) P -BR Air fuel ratio sensor Ignition switch ON 3.3 V*
B38-2 (A1A-) - B38-12 (E1) V - BR Air fuel ratio sensor Ignition switch ON 3.0 V*
B38-7 (A2A+) - B38-12 (E1) Y - BR Air fuel ratio sensor Ignition switch ON 3.3 V*
B38-8 (A2A-) - B38-12 (E1) L - BR Air fuel ratio sensor Ignition switch ON 3.0 V*
B39-12 (HT1B) - B39-11 (E03)
B39-13 (HT2B) - B39-11 (E03)
L-R - W-B
L - W-B
Heated oxygen sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
B36-2 (OX1B) - B36-1 (EX1B)
B36-4 (OX2B) - B36-3 (EX2B)
W - G-B
G - GR
Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation (see waveform 2)
B39-6 (#10) - B39-14 (E01)
B39-1 (#20) - B39-14 (E01)
B39-7 (#30) - B39-14 (E01)
B39-2 (#40) - B39-14 (E01)
B39-8 (#50) - B39-14 (E01)
B39-3 (#60) - B39-14 (E01)
L - W-B
B - W-B
R - W-B
G - W-B
Y - W-B
GR - W-B
Fuel injector Ignition switch ON 11 to 14 V
Idling Pulse generation (see waveform 3)
B37-11 (KNK1) - B37-12 (EKNK)
B37-5 (KNK2) - B37-6 (EKN2)
B - W
G - R
Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation (see waveform 4)
B36-15 (VCV1) - B38-12 (E1) P-L - BR Power source for VVT sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
B36-16 (VCV2) - B38-12 (E1) LG-B - BR Power source for VVT sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
B36-9 (VV1+) - B36-10 (VV1-) B-W - V VVT sensor (intake side of bank 1) Idling Pulse generation
(see waveform 5)
B36-12 (VV2+) - B36-11 (VV2-) G - GR VVT sensor (intake side of bank 2) Idling Pulse generation
(see waveform 5)
B36-13 (EV1+) - B36-14 (EV1-) W-R - R-B VVT sensor (exhaust side of bank 1) Idling Pulse generation
(see waveform 6)
B36-18 (EV2+) - B36-17 (EV2-) LG - P VVT sensor (exhaust side of bank 2) Idling Pulse generation
(see waveform 6)
B36-6 (NE+) - B36-5 (NE-) B - W Crankshaft position sensor Idling Pulse generation (see waveform 5)
B38-24 (IGT1) - B38-12 (E1)
B38-25 (IGT2) - B38-12 (E1)
B38-26 (IGT3) - B38-12 (E1)
B38-27 (IGT4) - B38-12 (E1)
B38-28 (IGT5) - B38-12 (E1)
B37-25 (IGT6) - B38-12 (E1)
R-Y - BR
W-R - BR
G-B - BR
LG-B - BR
GR - BR
L-W - BR
Ignition coil (ignition signal) Idling Pulse generation (see waveform 7)
B38-6 (IGF1) - B38-12 (E1) G-R - BR Ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation (see waveform 7)
B38-18 (PRG) - B38-12 (E1) P - BR Purge VSV Ignition switch ON 11 to 14 V
Idling Pulse generation (see waveform 8)
F51-18 (SPD) - B38-12 (E1) SB - BR Vehicle speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation (see waveform 9)
F50-10 (STA) - B38-12 (E1) W - BR Starter signal Cranking 5.5 V or higher
B37-2 (NSW) - B38-12 (E1) B - BR Starter relay control Ignition switch ON Below 1.5 V
Cranking 6.0 V or higher
F50-18 (STP) - B38-12 (E1) V - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
F51-8 (ST1-) - B38-12 (E1) B - BR Stop light switch
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
B39-20 (M+) - B39-10 (ME01) P - W-B Throttle actuator Idling with warm engine Pulse generation (see waveform 10)
B38-29 (M-) - B39-10 (ME01) L - W-B Throttle actuator Idling with warm engine Pulse generation (see waveform 11)
F50-8 (FC) - B38-12 (E1) G - BR Fuel pump control Ignition switch ON 11 to 14 V
Idling Below 1.5 V
F51-3 (FPC) - B38-12 (E1) G - BR Fuel pump control Ignition switch ON Below 1.5 V
F50-26 (DI) - B38-12 (E1) GR - BR Fuel pump control Ignition switch ON 0 to 3.0 V
F51-13 (W) - B38-12 (E1) L - BR MIL Ignition switch ON Below 1.5 V
Idling 11 to 14 V
F50-28 (TC) - B38-12 (E1) R - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
F50-29 (TACH) - B38-12 (E1) P - BR Engine speed Idling Pulse generation (see waveform 12)
B37-28 (ALT) - B38-12 (E1) L - BR Generator Ignition switch ON 11 to 14 V
F50-32 (CANH) - B38-12 (E1) V - BR CAN communication line Ignition switch ON Pulse generation (see waveform 13)
F50-31 (CANL) - B38-12 (E1) W - BR CAN communication line Ignition switch ON Pulse generation (see waveform 14)
B37-16 (PSP) - B38-12 (E1) W-G - BR Power steering oil pressure sensor Ignition switch ON 0.5 to 4.5 V

HINT:

*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.



b.
U115314E06
0.448,0.167 1.135,0.365 0.688,0.198 10 false 5 V/DIV. 0.5,1.135 0.938,1.333 0.438,0.198 10 false GND 1.479,1.917 2.375,2.115 0.896,0.198 10 false 1 msec./DIV.

Waveform 1

Camshaft Timing Oil Control Valve
Symbol Between OC1+ and OC1-
Between OC2+ and OC2-
Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling


c.
U115312E06
0.313,0.146 1.031,0.365 0.719,0.219 10 false 0.2 V/DIV. 0.5,1.5 0.885,1.698 0.385,0.198 10 false GND 1.656,1.854 2.656,2.052 1,0.198 10 false 200 msec./DIV.

Waveform 2

Heated Oxygen Sensor
Symbol Between OX1B and EX1B
Between OX2B and EX2B
Tester Range 0.2 V/DIV., 200 msec./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In Data List, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.



d.
A388709E01
0.479,0.208 1.198,0.417 0.719,0.208 10 false 20 V/DIV. 0.677,1.573 1.104,1.781 0.427,0.208 10 false GND 1.938,1.885 2.917,2.104 0.979,0.219 10 false 20 msec./DIV.

Waveform 3

Fuel Injector No. 1 (to No. 6) Injection Signal
Symbol Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



e.
A357198E14
2.396,0.406 3.042,0.583 0.646,0.177 10 false 1 V/DIV. 1.135,1.896 2.063,2.115 0.927,0.219 10 false 1 msec./DIV. 2.615,0.99 3.063,1.198 0.448,0.208 10 false GND

Waveform 4

Knock Sensor
Symbol Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 msec./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




f.
A122767E04
0.195,0.643 0.425,0.808 0.230,0.165 10 NE 0.122,1.13 0.426,1.281 0.304,0.151 10 VV1 0.126,1.512 0.425,1.657 0.299,0.145 10 VV2 2.9,0.633 3.237,0.782 0.336,0.149 10 GND 2.9,1.587 3.237,1.736 0.336,0.149 10 GND 2.9,1.204 3.237,1.353 0.336,0.149 10 GND 0.918,1.915 1.839,2.057 0.921,0.141 10 20 msec./DIV. 2.697,0.047 3.261,0.203 0.563,0.156 10 5 V/DIV.

Waveform 5

Crankshaft Position Sensor and VVT Sensor
Symbol Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



g.
A122768E04
0.185,0.653 0.401,0.803 0.216,0.150 10 NE 0.122,1.118 0.403,1.266 0.281,0.149 10 EV1 0.122,1.511 0.426,1.648 0.304,0.137 10 EV2 2.889,0.646 3.221,0.793 0.332,0.147 10 GND 2.889,1.208 3.221,1.355 0.332,0.147 10 GND 2.889,1.596 3.221,1.743 0.332,0.147 10 GND 2.637,0.139 3.236,0.295 0.599,0.156 10 5 V/DIV. 0.957,1.925 1.918,2.063 0.961,0.137 10 20 msec./DIV.

Waveform 6

Crankshaft Position Sensor and VVT Sensor
Symbol Between NE+ and NE-
Between EV1+ and EV1-
Between EV2+ and EV2-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



h.
A388710E01
0.25,0.604 0.583,0.802 0.333,0.198 10 false IGT 0.271,1.427 0.604,1.625 0.333,0.198 10 false IGF 2.927,1.875 3.26,2.073 0.333,0.198 10 false GND 2.948,1.021 3.281,1.219 0.333,0.198 10 false GND 2.75,0.313 3.375,0.5 0.625,0.188 10 false 2 V/DIV. 1.344,1.99 2.417,2.177 1.073,0.188 10 false 20 msec./DIV.

Waveform 7

Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM)
Symbol Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



i.
A149742E01
2.837,1.657 3.173,1.806 0.336,0.149 10 GND 0.794,2.622 1.715,2.763 0.921,0.141 10 20 msec./DIV. 2.537,0.639 3.170,0.795 0.633,0.156 10 10 V/DIV.

Waveform 8

Purge VSV
Symbol Between PRG and E1
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



j.
U115313E06
0.427,0.333 1.115,0.531 0.688,0.198 10 false 2 V/DIV. 0.5,1.188 0.896,1.385 0.396,0.198 10 false GND 1.563,1.917 2.521,2.115 0.958,0.198 10 false 20 msec./DIV.

Waveform 9

Vehicle Speed Signal
Symbol Between SPD and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



k.
U147433E05
0.51,0.271 1.083,0.469 0.573,0.198 10 false 5 V/DIV. 0.594,1.354 0.969,1.552 0.375,0.198 10 false GND 2.135,1.833 3.01,2.031 0.875,0.198 10 false 1 msec./DIV.

Waveform 10

Throttle Actuator Positive Terminal
Symbol Between M+ and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
U147434E03
0.521,0.135 1.063,0.333 0.542,0.198 10 false 5 V/DIV. 0.615,1.333 0.969,1.531 0.354,0.198 10 false GND 2.104,1.823 2.927,2.021 0.823,0.198 10 false 1 msec./DIV.

Waveform 11

Throttle Actuator Negative Terminal
Symbol Between M- and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



m.
U134016E03
0.333,0.292 1.031,0.49 0.698,0.198 10 false 5 V/DIV. 0.458,1.177 0.927,1.375 0.469,0.198 10 false GND 1.563,1.885 2.542,2.083 0.979,0.198 10 false 10 msec./DIV.

Waveform 12

Engine Speed Signal
Symbol Between TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



n.
A357201E08
2.979,1.396 3.385,1.594 0.406,0.198 10 false GND 2.76,0.292 3.323,0.479 0.563,0.188 10 false 1 V/DIV. 1.469,1.896 2.354,2.073 0.885,0.177 10 false 10 μsec./DIV.

Waveform 13

CAN Communication Signal
Symbol Between CANH and E1
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine stopped and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



o.
A357202E07
3.01,1.354 3.385,1.531 0.375,0.177 10 false GND 2.771,0.229 3.385,0.417 0.615,0.188 10 false 1 V/DIV. 1.448,1.865 2.354,2.063 0.906,0.198 10 false 10 μsec./DIV.

Waveform 14

CAN Communication Signal
Symbol Between CANL and E1
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine stopped and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.