Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A388715E01
1.583,2.042 1.865,1.708 false 0.073,0.094 0.583,0.354 0.51,0.26 10 false Fig. 1 0.063,0.448 0.771,0.688 0.708,0.24 10 false Resistance 0.094,0.844 0.438,1.052 0.344,0.208 10 false (kΩ) 1.76,1.458 2.469,1.698 0.708,0.24 10 false Acceptable 0.813,3.854 1.063,4.052 0.25,0.198 10 false -20 0.542,0.833 0.792,1.031 0.25,0.198 10 false 30 0.542,1.042 0.792,1.24 0.25,0.198 10 false 20 0.531,1.323 0.781,1.521 0.25,0.198 10 false 10 0.604,1.656 0.74,1.854 0.135,0.198 10 false 5 0.604,1.896 0.74,2.094 0.135,0.198 10 false 3 0.604,2.094 0.74,2.292 0.135,0.198 10 false 2 0.604,2.375 0.74,2.573 0.135,0.198 10 false 1 0.521,3.49 0.781,3.688 0.26,0.198 10 false 0.1 0.5,3.156 0.76,3.354 0.26,0.198 10 false 0.2 0.5,2.833 0.76,3.031 0.26,0.198 10 false 0.3 0.5,2.635 0.76,2.833 0.26,0.198 10 false 0.5 1.469,4.313 2.26,4.542 0.792,0.229 10 false Temperature 3.021,4.219 3.344,4.427 0.323,0.208 10 false (°C) 3.042,4.417 3.365,4.625 0.323,0.208 10 false (°F) 1.208,3.854 1.458,4.052 0.25,0.198 10 false 0 1.479,3.854 1.729,4.052 0.25,0.198 10 false 20 1.813,3.865 2.063,4.063 0.25,0.198 10 false 40 2.156,3.865 2.406,4.063 0.25,0.198 10 false 60 2.51,3.865 2.76,4.063 0.25,0.198 10 false 80 2.833,3.854 3.083,4.052 0.25,0.198 10 false 100 0.823,4.031 1.073,4.229 0.25,0.198 10 false (-4) 1.167,4.021 1.417,4.219 0.25,0.198 10 false 32 1.49,4.021 1.74,4.219 0.25,0.198 10 false 68 1.771,4.021 2.021,4.219 0.25,0.198 10 false 104 2.125,4.01 2.375,4.208 0.25,0.198 10 false 140 2.458,4.021 2.708,4.219 0.25,0.198 10 false 178 2.854,4.01 3.104,4.208 0.25,0.198 10 false 212

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When either DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. The ECM continues operating in fail-safe mode until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0112 Short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit


·

Intake air temperature sensor (built into mass air flow meter)


·

ECM


P0113 Open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit


·

Intake air temperature sensor (built into mass air flow meter)


·

ECM



HINT:

When any of these DTCs are stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit and stores DTC P0113. Conversely, if the output voltage is below 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit and stores DTC P0112.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

WIRING DIAGRAM

A223345E01
2.032,0.605 2.353,0.754 0.321,0.149 10 THA 0.801,1.979 2.143,2.136 1.342,0.157 10 Mass Air Flow Meter 0.805,1.825 1.079,1.973 0.274,0.148 10 B35 2.154,1.238 2.350,1.384 0.196,0.146 10 E2 5.272,0.603 5.456,0.756 0.184,0.153 10 15 5.336,1.229 5.458,1.397 0.122,0.169 10 7 5.534,0.603 5.831,0.753 0.297,0.149 10 THA 5.531,1.229 5.929,1.386 0.399,0.157 10 ETHA 6.225,0.243 6.484,0.404 0.258,0.162 10 5 V 5.997,2.42 6.333,2.592 0.336,0.172 10 ECM 5.999,2.262 6.273,2.420 0.274,0.157 10 B37 2.433,0.597 2.540,0.751 0.107,0.153 10 1 2.433,1.235 2.540,1.388 0.107,0.153 10 2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


e.

Read the value displayed on the intelligent tester.

OK:

Same as actual intake air temperature.


Result
Temperature Displayed Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).


·

If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
U149585E01
0.789,0.071 0.978,0.227 0.188,0.156 10 *1 0.199,1.767 0.387,1.923 0.188,0.156 10 *a 2.554,0.071 2.742,0.227 0.188,0.156 10 *2 2.399,0.822 2.754,0.982 0.355,0.161 10 THA 2.399,1.278 2.837,1.438 0.438,0.161 10 ETHA 0.257,2.517 0.530,2.676 0.273,0.159 10 B35 0.669,3.131 0.982,3.291 0.313,0.161 10 THA 2.325,3.131 2.522,3.291 0.198,0.161 10 E2 1.374,2.718 0.864,3.113 false 1.631,2.724 2.273,3.222 false

a.

Disconnect the mass air flow meter connector.

Text in Illustration
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


b.

Connect terminals THA and E2 of the mass air flow meter wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


g.

Read the value displayed on the intelligent tester.

Standard value:

140°C (284°F) or higher



h.

Reconnect the mass air flow meter connector.



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-1 (THA) - B37-15 (THA) Always Below 1 Ω
B35-2 (E2) - B37-7 (ETHA) Always Below 1 Ω



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
A211723E14
0.698,0.125 0.906,0.302 0.208,0.177 10 false *1 2.542,0.125 2.75,0.302 0.208,0.177 10 false *2 2.427,1.01 2.948,1.188 0.521,0.177 10 false THA 2.438,1.448 2.958,1.625 0.521,0.177 10 false ETHA

a.

Disconnect the mass air flow meter connector.

Text in Illustration
*1 Mass Air Flow Meter
*2 ECM


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


f.

Read the value displayed on the intelligent tester.

Standard value:

-40°C (-40°F)



g.

Reconnect the mass air flow meter connector.



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-1 (THA) or B37-15 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR