Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  


DESCRIPTION

Flat-type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 6 kHz and 15 kHz.

2 knock sensors are fitted onto the engine block to detect engine knocking.

Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327
P0332
Output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


P0328
P0333
Output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
·

Open in knock sensor circuit

·

Knock sensor

·

ECM



HINT:

When DTC P0327, P0328, P0332 or P0333 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A357198E15
2.552,0.167 3.198,0.344 0.646,0.177 10 false 1 V/DIV. 1.135,1.865 2.115,2.104 0.979,0.24 10 false 1 msec./DIV. 2.615,0.99 3.063,1.198 0.448,0.208 10 false GND 0.698,0.063 2.323,0.281 1.625,0.219 10 false KNK1 Signal Waveform

The correct waveform is as shown.

Item Content
Terminal KNK1 - EKNK
KNK2 - EKN2
Equipment Setting 1 V/DIV.
1 msec./DIV.
Condition Engine speed at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit and stores a DTC.

The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run 5 seconds after the engine is started.

If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

WIRING DIAGRAM

A227107E01
0.48,2.11 2.162,2.270 1.682,0.160 10 Knock Sensor (for Bank 1) 0.476,1.957 0.676,2.126 0.200,0.169 10 e2 0.463,3.913 2.145,4.091 1.682,0.179 10 Knock Sensor (for Bank 2) 0.466,3.77 0.660,3.921 0.194,0.151 10 e1 1.566,0.72 1.662,0.884 0.095,0.164 10 2 1.566,1.54 1.671,1.729 0.105,0.190 10 1 1.571,2.521 1.679,2.690 0.107,0.169 10 2 1.578,3.349 1.705,3.509 0.127,0.160 10 1 5.203,0.72 5.392,0.861 0.188,0.141 10 11 5.18,1.537 5.356,1.717 0.175,0.180 10 12 5.256,2.529 5.378,2.698 0.122,0.169 10 5 5.251,3.354 5.364,3.514 0.112,0.160 10 6 2.606,2.993 3.195,3.151 0.589,0.158 10 Shielded 2.606,1.165 3.195,1.323 0.589,0.158 10 Shielded 4.357,1.95 4.946,2.107 0.589,0.158 10 Shielded 4.357,3.722 4.946,3.880 0.589,0.158 10 Shielded 5.424,0.71 5.815,0.860 0.390,0.150 10 KNK1 5.419,1.536 5.864,1.686 0.445,0.150 10 EKNK 5.419,2.527 5.800,2.694 0.381,0.167 10 KNK2 5.419,3.346 5.799,3.497 0.380,0.151 10 EKN2 5.746,4.412 6.096,4.571 0.350,0.160 10 ECM 5.742,4.263 6.016,4.442 0.274,0.179 10 B37 3.291,0.611 3.420,0.780 0.129,0.169 10 2 3.206,0.806 3.480,0.965 0.274,0.160 10 Be1 3.284,1.426 3.401,1.609 0.117,0.183 10 5 3.207,1.621 3.471,1.781 0.264,0.160 10 Be1 3.284,1.929 3.401,2.112 0.117,0.183 10 1 3.207,2.124 3.471,2.283 0.264,0.160 10 Be1 3.207,2.605 3.481,2.765 0.274,0.160 10 Be1 3.211,3.427 3.496,3.595 0.285,0.168 10 Be1 3.285,2.421 3.434,2.617 0.149,0.195 10 4 3.285,3.251 3.434,3.446 0.149,0.195 10 6

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.

·

DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK KNOCK SENSOR
U150122E01
0.057,0.005 0.309,0.207 0.251,0.202 10 *a 1.633,2.581 1.869,1.923 false 1.844,0.35 2.144,0.509 0.301,0.159 10 B37 0.927,1.946 1.550,2.148 0.622,0.202 10 6 (EKN2) 0.867,2.565 1.559,2.766 0.692,0.202 10 12 (EKNK) 2.293,2.581 1.915,1.923 false 1.631,1.978 1.869,1.859 false 2.312,1.994 1.915,1.859 false 2.32,1.954 2.913,2.144 0.592,0.190 10 5 (KNK2) 2.299,2.547 2.971,2.737 0.672,0.190 10 11 (KNK1)

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-11 (KNK1) - B37-12 (EKNK) 20°C (68°F) 120 to 280 kΩ
B37-5 (KNK2) - B37-6 (EKN2) 20°C (68°F) 120 to 280 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to ECM)


c.

Reconnect the ECM connector.



OK

2.CHECK TERMINAL VOLTAGE (ECM)

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
2.CHECK TERMINAL VOLTAGE (ECM)
U149622E01
0.063,0.019 0.237,0.193 0.174,0.174 10 *a 1.505,1.86 1.879,0.893 false 1.853,0.329 2.154,0.487 0.301,0.159 10 B37 0.548,1.546 1.170,1.748 0.622,0.202 10 6 (EKN2) 0.74,1.844 1.431,2.046 0.692,0.202 10 12 (EKNK) 2.103,1.889 1.924,0.893 false 1.251,1.579 1.879,0.83 false 2.293,1.571 1.924,0.83 false 2.301,1.532 2.893,1.722 0.592,0.190 10 5 (KNK2) 2.108,1.855 2.780,2.045 0.672,0.190 10 11 (KNK1)

a.

Disconnect the Be1 connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B37-11 (KNK1) - B37-12 (EKNK) Ignition switch ON 4.5 to 5.5 V
B37-5 (KNK2) - B37-6 (EKN2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
a.

Disconnect the knock sensor connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
e2-2 - B37-11 (KNK1) Always Below 1 Ω
e2-1 - B37-12 (EKNK) Always Below 1 Ω
e1-2 - B37-5 (KNK2) Always Below 1 Ω
e1-1 - B37-6 (EKN2) Always Below 1 Ω
e2-2 or B37-11 (KNK1) - Body ground Always 10 kΩ or higher
e2-1 or B37-12 (EKNK) - Body ground Always 10 kΩ or higher
e1-2 or B37-5 (KNK2) - Body ground Always 10 kΩ or higher
e1-1 or B37-6 (EKN2) - Body ground Always 10 kΩ or higher


d.

Reconnect the knock sensor connectors.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR