The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.
The normal switch conditions are as shown in the table below.
| Signal | Brake Pedal Released | In Transition | Brake Pedal Depressed |
|---|---|---|---|
| STP | OFF | ON | ON |
| ST1- | ON | ON | OFF |
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0504 | Conditions (a), (b) and (c) are met for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON. (b) Brake pedal is released. (c) STP signal is OFF when the ST1- signal is OFF. |
·
Short in stop light switch signal circuit ·
STOP fuse ·
IGN fuse ·
Stop light switch assembly ·
No. 1 integration relay ·
ECM |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
STP signal conditions can be checked using the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
Check the STP signal when the brake pedal is depressed and released.
| Brake Pedal Operation | Specified Condition |
|---|---|
| Depressed | STP signal ON |
| Released | STP signal OFF |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-7 (B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Reconnect the stop light switch assembly connector.
OK
NG
Disconnect the stop light switch assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A41-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Reconnect the stop light switch assembly connector.
OK
NG
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-2 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the stop light switch assembly connector.
OK
NG
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Operation | Specified Condition |
|---|---|---|
| F51-8 (ST1-) - Body ground | Released | 7.5 to 14 V |
| Depressed | Below 1.5 V | |
| F50-18 (STP) - Body ground | Released | Below 1.5 V |
| Depressed | 7.5 to 14 V |
| *a | Brake Pedal Depressed |
| *b | Brake Pedal Released |
| *c | Rear view of wire harness connector
(to ECM) |
Reconnect the ECM connector.
OK
NG
Disconnect the stop light switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-3 (L) - F50-18 (STP) | Always | Below 1 Ω |
| A41-5 (L) - F51-8 (ST1-) | Always | Below 1 Ω |
| A41-3 (L) or F50-18 (STP) - Body ground | Always | 10 kΩ or higher |
| A41-5 (L) or F51-8 (ST1-) - Body ground | Always | 10 kΩ or higher |
Reconnect the stop light switch assembly connector.
Reconnect the ECM connector.
OK
NG
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1C-4 - A41-6 (B) | Always | Below 1 Ω |
| 1C-4 or A41-6 (B) - Body ground | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay from the engine room relay block and junction block assembly.
Reconnect the stop light switch assembly connector.
OK
NG