Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in the ECM backup power source circuit (1 trip detection logic).
·

Open in backup power source circuit

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A227108E01
1.185,2.318 1.660,2.483 0.475,0.165 10 Battery 1.918,1.287 2.260,1.442 0.342,0.155 10 P/I-B 3.527,1.271 3.780,1.455 0.253,0.184 10 EFI 5.291,0.918 5.468,1.097 0.177,0.179 10 24 5.249,1.109 5.522,1.264 0.273,0.155 10 F51 5.28,2.158 5.474,2.322 0.194,0.165 10 12 5.249,2.339 5.515,2.497 0.267,0.158 10 B38 5.582,1.103 5.958,1.267 0.376,0.165 10 BATT 5.578,2.338 5.772,2.505 0.194,0.166 10 E1 5.957,3.262 6.299,3.427 0.342,0.165 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Battery positive terminal - F51-24 (BATT) Always Below 1 Ω
Battery positive terminal or F51-24 (BATT) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the cable to the positive (+) battery terminal.



OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Turn the ignition switch off and turn the intelligent tester off.


e.

Start the engine and turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0560 A
No output B



A

B