Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2009.08–2016.12
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) Vehicle speed is 20 km/h (12.4 mph) or more.

(b) Engine speed is 1000 rpm or more.

(c) STA signal is on.


·

Park/neutral position switch

·

Starter relay (ST) circuit

·

Ignition switch

·

ECM



WIRING DIAGRAM

A227113E02
1.831,1.445 2.139,1.607 0.309,0.163 10 ST1 1.831,2.182 2.139,2.345 0.309,0.163 10 ST2 1.345,1.445 1.654,1.607 0.309,0.163 10 AM1 0.271,2.332 0.579,2.495 0.309,0.163 10 AM1 1.345,2.182 1.654,2.345 0.309,0.163 10 AM2 2.156,1.218 2.284,1.395 0.128,0.177 10 1 2.156,1.958 2.284,2.135 0.128,0.177 10 8 1.166,1.218 1.294,1.395 0.128,0.177 10 2 1.166,1.958 1.294,2.135 0.128,0.177 10 7 1.216,2.44 1.483,2.589 0.267,0.149 10 F15 1.216,2.587 2.192,2.743 0.975,0.156 10 Ignition Switch 5.843,1.127 5.965,1.276 0.121,0.149 10 2 5.143,1.757 5.264,1.906 0.121,0.149 10 4 4.898,2.549 5.019,2.698 0.121,0.149 10 5 5.769,1.313 6.050,1.469 0.281,0.156 10 B37 6.099,1.305 6.470,1.461 0.371,0.156 10 NSW 5.083,2.573 5.378,2.729 0.295,0.156 10 B42 5.083,2.721 6.066,3.210 0.982,0.489 10 Park/Neutral Position Switch Assembly 0.955,3.195 1.166,3.350 0.211,0.156 10 ST 3.696,4.465 3.908,4.621 0.211,0.156 10 ST 1.158,4.248 1.286,4.411 0.128,0.163 10 1 1.992,4.15 2.120,4.312 0.128,0.163 10 1 1.109,4.444 1.327,4.607 0.218,0.163 10 C3 2.19,4.155 2.411,4.314 0.222,0.159 10 C4 1.06,5.81 1.542,5.994 0.482,0.184 10 Battery 1.543,5.249 2.658,5.419 1.114,0.170 10 Starter Assembly 3.346,3.631 3.467,3.780 0.121,0.149 10 3 4.12,3.631 4.241,3.780 0.121,0.149 10 5 3.346,4.059 3.467,4.207 0.121,0.149 10 2 4.12,4.059 4.241,4.207 0.121,0.149 10 1 5.798,3.967 5.989,4.123 0.191,0.156 10 10 5.777,4.164 6.058,4.326 0.281,0.163 10 F50 6.099,4.171 6.394,4.320 0.295,0.149 10 STA 6.295,4.605 6.639,4.775 0.343,0.170 10 ECM 0.287,3.797 0.647,3.981 0.360,0.184 12 ALT

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the value displayed on the intelligent tester when the ignition switch is turned to ON and the engine is started.

OK:
Condition Starter Signal
Ignition switch turned to ON Close
Engine started Open




OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly for 4WD (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION).


b.

Inspect the park/neutral position switch assembly for 2WD (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STA TERMINAL OF ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STA TERMINAL OF ECM)

NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0617 A
No DTC B



A

B

END