Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, the ECM then allows the current to flow to the throttle actuator so that it can be restarted after the ignition switch is turned off.

HINT:

This ETCS does not use a throttle cable.


A112629E07
0.24,1.665 0.840,2.045 0.600,0.380 10 from Battery 0.796,2.058 2.010,2.260 1.214,0.202 10 Throttle Actuator 1.23,1.637 2.164,1.839 0.934,0.202 10 ETCS 5.609,0.199 6.059,0.401 0.450,0.202 10 ECM 4.761,1.693 5.211,1.895 0.450,0.202 10 +BM 4.761,3.753 5.278,3.955 0.517,0.202 10 ME01 4.761,2.422 5.078,2.624 0.317,0.202 10 M+ 4.761,3.066 5.078,3.268 0.317,0.202 10 M- 5.94,2.437 6.559,3.155 0.619,0.718 10 Throttle Actuator Control Circuit 4.761,0.917 5.211,1.119 0.450,0.202 10 +B 0.139,0.936 0.944,1.338 0.805,0.401 10 from EFI MAIN Relay 5.934,0.747 6.476,1.466 0.542,0.718 10 Power Source Circuit for CPU

DTC No. DTC Detection Condition Trouble Area
P2118 Open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in ETCS power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM



MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A227104E01
1.381,3.265 1.678,3.426 0.298,0.161 10 B13 1.388,3.426 3.610,3.619 2.222,0.193 10 Throttle Body with Motor Assembly 0.927,4.11 1.389,4.313 0.461,0.202 10 Battery 4.112,1.81 4.685,1.989 0.573,0.179 10 Shielded 2.89,1.132 3.296,1.315 0.406,0.183 10 ETCS 5.536,0.803 5.743,0.954 0.207,0.151 10 23 5.496,0.987 5.767,1.133 0.271,0.146 10 B38 5.812,0.897 6.153,1.062 0.341,0.165 10 +BM 5.537,1.96 5.784,2.097 0.247,0.137 10 20 5.5,2.154 5.785,2.347 0.286,0.193 10 B39 5.539,2.587 5.738,2.751 0.199,0.163 10 29 5.501,2.768 5.784,2.919 0.283,0.151 10 B38 2.767,2.061 3.000,2.217 0.232,0.156 10 M+ 2.781,2.677 2.985,2.824 0.204,0.147 10 M- 3.066,2.054 3.183,2.210 0.117,0.156 10 2 3.065,2.671 3.174,2.840 0.110,0.170 10 1 5.535,3.186 5.728,3.342 0.193,0.156 10 30 5.501,3.368 5.794,3.523 0.293,0.156 10 B38 5.532,3.775 5.725,3.945 0.193,0.170 10 10 5.501,3.955 5.795,4.101 0.294,0.146 10 B39 5.531,4.368 5.724,4.556 0.193,0.188 10 12 5.5,4.548 5.803,4.689 0.303,0.142 10 B38 5.816,2.056 6.046,2.235 0.230,0.179 10 M+ 5.812,2.672 6.005,2.819 0.193,0.147 10 M- 5.812,3.354 6.200,3.524 0.387,0.170 10 GE01 5.815,3.859 6.198,4.002 0.383,0.144 10 ME01 5.815,4.54 6.010,4.712 0.195,0.172 10 E1 6.13,5.11 6.480,5.275 0.350,0.165 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / +BM Voltage.


e.

Read the value displayed on the intelligent tester.

Result
Result Proceed to
Below 11 V or higher than 14 V A
11 to 14 V B



A

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B38-23 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B38-12 (E1) - Body ground Always Below 1 Ω
B39-10 (ME01) - Body ground Always Below 1 Ω



d.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR