Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


CAUTION / NOTICE / HINT

DESCRIPTION

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the amount the accelerator pedal is depressed (throttle valve opening angle). The signal from VPA indicates the actual accelerator pedal position (throttle valve opening angle) and is used for engine control. The signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal position (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


A112620E47
0.096,3.802 2.261,3.968 2.165,0.166 10 Accelerator Pedal Position Sensor 1.263,1.669 1.744,1.850 0.480,0.181 10 Magnet 0.339,1.842 0.865,2.023 0.526,0.181 10 IC No. 1 0.311,3.318 0.837,3.499 0.526,0.181 10 IC No. 2 2.155,1.739 2.450,1.921 0.295,0.181 10 VPA 6.438,2.272 6.733,2.453 0.295,0.181 10 VPA 2.155,2.071 2.450,2.252 0.295,0.181 10 EPA 2.104,2.393 2.499,2.574 0.395,0.181 10 VCPA 2.116,2.687 2.488,2.869 0.372,0.181 10 VPA2 6.394,1.816 6.766,1.997 0.372,0.181 10 VPA2 2.116,3.005 2.488,3.186 0.372,0.181 10 EPA2 2.112,3.327 2.492,3.508 0.380,0.181 10 VCP2 2.693,3.802 3.018,3.983 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.414,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.369,4.054 6.794,4.257 2.424,0.202 10 Accelerator Pedal Angle (°) 4.369,4.363 6.648,4.544 2.279,0.181 10 *1: Accelerator Pedal Fully Released 4.369,4.671 6.756,4.836 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.867,3.491 1.347,3.672 0.480,0.181 10 Magnet 0.843,2.878 0.554,3.289 false 0.965,3.195 1.049,3.475 false 0.927,2.504 0.862,1.934 false 1.067,2.205 1.245,1.729 false 0.689,1.181 4.021,1.383 3.332,0.202 10 Accelerator Pedal Position Sensor Output Voltage (V) 4.355,1.841 4.08,1.28 false

DTC No. DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly


·

ECM


P2122 VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal sensor assembly


·

Open in VCPA circuit


·

Open or ground short in VPA circuit


·

ECM


P2123 VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly


·

Open in EPA circuit


·

ECM


P2125 VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly


·

ECM


P2127 VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal sensor assembly


·

Open in VCP2 circuit


·

Open or ground short in VPA2 circuit


·

ECM


P2128 Conditions (a) and (b) are met for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal sensor assembly


·

Open in EPA2 circuit


·

ECM


P2138 Condition (a) or (b) is met for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits


·

Accelerator pedal sensor assembly


·

ECM



HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area Accel Sensor Out No.1
When Accelerator Pedal Released
Accel Sensor Out No.2
When Accelerator Pedal Released
Accel Sensor Out No.1
When Accelerator Pedal Depressed
Accel Sensor Out No.2
When Accelerator Pedal Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.7 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.7 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A227105E01
0.305,3.289 0.519,3.454 0.214,0.165 10 A3 0.309,3.429 2.601,3.583 2.291,0.155 10 Accelerator Pedal Sensor Assembly 1.596,0.751 1.894,0.906 0.298,0.155 10 VPA 1.598,1.166 1.901,1.331 0.303,0.165 10 EPA 1.497,1.605 1.918,1.750 0.421,0.145 10 VCPA 1.511,2.016 1.905,2.166 0.394,0.150 10 VPA2 1.501,2.854 1.905,3.009 0.404,0.155 10 VCP2 1.515,2.427 1.914,2.582 0.399,0.155 10 EPA2 6.038,3.293 6.344,3.448 0.306,0.155 10 F50 6.038,3.45 6.380,3.605 0.342,0.155 10 ECM 5.43,0.653 5.558,0.813 0.128,0.160 10 6 5.43,1.063 5.560,1.214 0.130,0.151 10 3 5.432,1.494 5.539,1.674 0.107,0.181 10 4 5.428,1.913 5.525,2.077 0.097,0.165 10 5 5.428,2.33 5.534,2.514 0.106,0.184 10 1 5.43,2.745 5.570,2.927 0.140,0.182 10 2 1.991,0.653 2.118,0.813 0.128,0.160 10 6 1.991,1.063 2.121,1.214 0.130,0.151 10 5 1.993,1.494 2.099,1.674 0.107,0.181 10 4 1.989,1.913 2.086,2.077 0.097,0.165 10 3 1.989,2.33 2.094,2.514 0.106,0.184 10 2 1.991,2.745 2.131,2.927 0.140,0.182 10 1 5.591,0.649 5.916,0.819 0.325,0.170 10 VPA 5.591,1.067 5.918,1.251 0.327,0.184 10 EPA 5.593,1.478 6.004,1.623 0.411,0.145 10 VCPA 5.595,1.895 5.978,2.050 0.383,0.155 10 VPA2 5.587,2.338 5.969,2.493 0.381,0.155 10 EPA2 5.595,2.755 5.981,2.920 0.386,0.165 10 VCP2

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the accelerator pedal position sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT NO.1 AND ACCEL SENSOR OUT NO.2)
A208621E02
0.67,1.751 0.875,1.925 0.205,0.174 10 *a 2.612,1.751 2.803,1.925 0.191,0.174 10 *b

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.


d.

Read the value displayed on the intelligent tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No.1 Accel Sensor Out No.2
Released → Depressed → Released 0.5 to 4.5 V 1.2 to 4.7 V
Difference between Accel Sensor Out No.1 and Accel Sensor Out No.2 is more than 0.02 V Difference between Accel Sensor Out No.1 and Accel Sensor Out No.2 is more than 0.02 V


Text in Illustration
*a Depressed
*b Released



OK

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-6 (VPA) - F50-6 (VPA) Always Below 1 Ω
A3-5 (EPA) - F50-3 (EPA) Always Below 1 Ω
A3-4 (VCPA) - F50-4 (VCPA) Always Below 1 Ω
A3-3 (VPA2) - F50-5 (VPA2) Always Below 1 Ω
A3-2 (EPA2) - F50-1 (EPA2) Always Below 1 Ω
A3-1 (VCP2) - F50-2 (VCP2) Always Below 1 Ω
A3-6 (VPA) or F50-6 (VPA) - Body ground Always 10 kΩ or higher
A3-5 (EPA) or F50-3 (EPA) - Body ground Always 10 kΩ or higher
A3-4 (VCPA) or F50-4 (VCPA) - Body ground Always 10 kΩ or higher
A3-3 (VPA2) or F50-5 (VPA2) - Body ground Always 10 kΩ or higher
A3-2 (EPA2) or F50-1 (EPA2) - Body ground Always 10 kΩ or higher
A3-1 (VCP2) or F50-2 (VCP2) - Body ground Always 10 kΩ or higher



d.

Reconnect the accelerator pedal sensor assembly connector.


e.

Reconnect the ECM connector.



OK

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)
U149579E01
1.356,1.099 0.743,1.641 false 1.492,1.108 1.363,1.644 false 1.784,1.112 2.008,1.629 false 1.94,1.097 2.665,1.64 false 0.488,0.949 0.752,1.130 0.264,0.181 10 A3 1.138,1.665 1.533,1.846 0.394,0.181 10 EPA2 1.789,1.665 2.187,1.846 0.399,0.181 10 VCPA 0.379,1.665 0.759,1.846 0.380,0.181 10 VCP2 0.039,0 0.195,0.181 0.156,0.181 10 *a 2.54,1.665 2.890,1.842 0.350,0.177 10 EPA

a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-4 (VCPA) - A3-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A3-1 (VCP2) - A3-2 (EPA2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


d.

Reconnect the accelerator pedal sensor assembly connector.



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 A
No output B



A

B

SYSTEM OK