Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

The VVT (variable valve timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E13
4.483,0.815 5.318,1.026 0.834,0.211 10 VVT Sensor 4.483,1.325 6.234,1.485 1.751,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.765,3.922 2.166,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.483,1.827 5.818,1.981 1.334,0.154 10 Mass Air Flow Meter 4.483,2.854 6.799,3.042 2.316,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.049,2.511 1.566,0.167 10 Throttle Position Sensor 4.483,3.353 5.929,3.506 1.446,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in the camshaft timing oil control valve for the intake camshaft (bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for intake camshaft (bank 1) circuit

·

Camshaft timing oil control valve for intake camshaft (bank 1)

·

ECM


P0020 Open or short in the camshaft timing oil control valve for the intake camshaft (bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for intake camshaft (bank 2) circuit

·

Camshaft timing oil control valve for intake camshaft (bank 2)

·

ECM



HINT:

These DTCs relate to the camshaft oil control valves.


WIRING DIAGRAM

A227098E01
0.126,1.685 2.958,2.014 2.833,0.329 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 1) 0.136,3.676 2.912,4.042 2.776,0.367 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 2) 1.471,0.52 1.602,0.717 0.130,0.197 10 1 1.483,1.249 1.599,1.478 0.116,0.230 10 2 1.425,2.48 1.581,2.661 0.156,0.181 10 1 1.475,3.223 1.587,3.425 0.111,0.203 10 2 5.098,0.407 5.314,0.584 0.215,0.178 10 19 5.075,0.611 5.362,0.766 0.287,0.155 10 B37 5.119,1.144 5.302,1.340 0.183,0.197 10 20 5.111,2.384 5.309,2.553 0.198,0.169 10 19 5.119,3.119 5.298,3.297 0.179,0.178 10 20 5.078,1.348 5.350,1.507 0.272,0.159 10 B37 5.078,2.583 5.347,2.742 0.269,0.159 10 B36 5.074,3.325 5.352,3.493 0.278,0.168 10 B36 0.153,1.483 0.425,1.642 0.272,0.159 10 B16 0.171,3.446 0.443,3.596 0.272,0.149 10 B19 5.4,0.508 5.807,0.667 0.407,0.159 10 OC1+ 5.401,1.249 5.787,1.418 0.385,0.168 10 OC1- 5.396,2.486 5.791,2.654 0.395,0.168 10 OC2+ 5.401,3.221 5.760,3.380 0.360,0.159 10 OC2- 5.91,4.185 6.241,4.336 0.331,0.152 10 ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs after recording the freeze frame data and DTCs.


b.

Turn the ignition switch off.


c.

Allow the engine to idle and check for DTCs.


d.

Check that P0010 or P0020 is output.

OK:

P0010 or P0020 is output.




OK

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (for Intake Side of Bank 1, 2) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B16-1 - B37-19 (OC1+) Always Below 1 Ω
B19-1 - B36-19 (OC2+) Always Below 1 Ω
B16-2 - B37-20 (OC1-) Always Below 1 Ω
B19-2 - B36-20 (OC2-) Always Below 1 Ω
B16-1 or B37-19 (OC1+) - Body ground Always 10 kΩ or higher
B19-1 or B36-19 (OC2+) - Body ground Always 10 kΩ or higher
B16-2 or B37-20 (OC1-) - Body ground Always 10 kΩ or higher
B19-2 or B36-20 (OC2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft timing oil control valve assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR