Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)  P2241  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)  P2242  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  P2255  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)  P2256  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)  


CAUTION / NOTICE / HINT

DESCRIPTION

The air fuel ratio sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.

The air fuel ratio sensor is of the planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows through the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. The heat generated by the heater is conducted to the solid electrolyte through the alumina, thereby accelerating the sensor activation.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: The value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A225212E07
3.063,2.552 3.396,2.865 false 2.885,2.365 3.396,2.552 false 2.99,1.99 3.375,1.917 false 3.042,2.302 3.396,2.552 false 3.219,1.833 3.365,1.469 3.365,1.469 3.406,1.469 false 1.781,2.573 2.063,2.573 false 1.604,2.594 1,2.208 1,2.208 0.958,2.208 false 1.135,3.073 1.26,3.271 0.125,0.198 10 false A 2.021,3.083 2.146,3.281 0.125,0.198 10 false A 0.406,2.115 0.948,2.271 0.542,0.156 10 false Element 0.094,2.938 0.979,3.156 0.885,0.219 10 false Exhaust Gas 2.698,3.156 3.49,3.375 0.792,0.219 10 false A-A Section 3.417,2.469 4.625,2.688 1.208,0.219 10 false Platinum Electrode 2.094,2.479 2.656,2.698 0.563,0.219 10 false Cover 3.417,2.833 3.708,3.031 0.292,0.198 10 false Air 3.438,1.385 3.875,1.604 0.438,0.219 10 false Heater 3.406,1.771 4.594,2.156 1.188,0.385 10 false Solid Electrolyte (Zirconia Element) 5.156,3.094 6.865,3.313 1.708,0.219 10 false Rich - Air-fuel Ratio - Lean 5.771,0.417 7.125,0.635 1.354,0.219 10 false Ideal Air-Fuel Mixture 4.354,0.615 5.344,0.823 0.99,0.208 10 false Output Voltage 4.698,0.99 4.917,1.198 0.219,0.208 10 false (V) 4.656,2.573 4.875,2.729 0.219,0.156 10 false 2.4 4.656,2.417 4.875,2.573 0.219,0.156 10 false 2.6 4.656,2.25 4.875,2.406 0.219,0.156 10 false 2.8 4.656,2.094 4.875,2.25 0.219,0.156 10 false 3.0 4.656,1.927 4.875,2.083 0.219,0.156 10 false 3.2 4.656,1.771 4.875,1.927 0.219,0.156 10 false 3.4 4.656,1.615 4.875,1.771 0.219,0.156 10 false 3.6 4.656,1.458 4.875,1.615 0.219,0.156 10 false 3.8 4.656,1.302 4.875,1.458 0.219,0.156 10 false 4.0 5.073,2.844 5.271,3.01 0.198,0.167 10 false 12 5.302,2.844 5.5,3.01 0.198,0.167 10 false 13 5.531,2.844 5.729,3.01 0.198,0.167 10 false 14 5.771,2.844 5.969,3.01 0.198,0.167 10 false 15 6,2.844 6.198,3.01 0.198,0.167 10 false 16 6.229,2.844 6.427,3.01 0.198,0.167 10 false 17 6.458,2.844 6.656,3.01 0.198,0.167 10 false 18 6.688,2.844 6.885,3.01 0.198,0.167 10 false 19 0.125,0.052 2.844,0.469 2.719,0.417 12 false w/o Secondary Air Injection System:

A234900E47
1.615,2.969 0.979,2.49 false 1.823,2.969 2.094,2.667 false 2.927,1.76 3.521,0.729 false 3.052,1.792 3.615,1.427 false 3.208,2.188 3.698,1.781 false 2.854,2.396 3.583,2.198 3.583,2.198 3,2.396 false 3.063,2.469 3.49,2.74 false 0.156,3.271 0.99,3.615 0.833,0.344 10 false Exhaust Gas 0.438,2.375 0.979,2.708 0.542,0.333 10 false Element 2.115,2.563 2.51,2.865 0.396,0.302 10 false Cover 1.125,3.427 1.271,3.625 0.146,0.198 10 false A 2.01,3.427 2.156,3.625 0.146,0.198 10 false A 3.552,0.646 4.708,1.292 1.156,0.646 10 false Solid Electrolyte (Zirconia Element) 3.625,1.313 4.448,1.615 0.823,0.302 10 false Alumina 3.719,1.708 4.708,1.99 0.99,0.281 10 false Heater 3.604,2.125 5.021,2.469 1.417,0.344 10 false Platinum Electrode 3.51,2.646 4.521,2.99 1.01,0.344 10 false Atmospheric Air 2.583,3.167 3.75,3.531 1.167,0.365 10 false A-A Cross Section 5.698,3.167 6.594,3.51 0.896,0.344 10 false Air Fuel Ratio 5.104,0.667 6.979,1.26 1.875,0.594 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 0.156,0.146 2.875,0.396 2.719,0.25 12 false w/ Secondary Air Injection System:

DTC No. DTC Detection Condition Trouble Area
P2237
P2240
Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2238
P2241
·

Case 1:


Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic):
(a) AF+ voltage is 0.5 V or less.
(b) (AF+) - (AF-) is 0.1 V or less.
·

Case 2:


Air fuel ratio sensor admittance is below 0.022 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2239
P2242
AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2252
P2255
AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2253
P2256
AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM



HINT:
·

DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

·

Bank 1 refers to the bank that includes cylinder NO. 1.

·

Bank 2 refers to the bank that includes cylinder NO. 2.



MONITOR DESCRIPTION

The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the air fuel ratio sensor circuit.

CONFIRMATION DRIVING PATTERN

A199234E02
0.88,1.207 1.268,1.414 0.387,0.207 10 Idling 0.105,1.618 1.316,1.783 1.211,0.165 10 Ignition Switch ON 1.796,1.758 2.021,1.937 0.225,0.179 10 [A] 2.759,2.906 2.984,3.131 0.225,0.225 10 [B] 5.41,2.944 5.612,3.156 0.202,0.211 10 [C] 3.736,2.33 4.478,2.484 0.742,0.154 10 3 minutes 2.09,2.355 2.831,2.509 0.742,0.154 10 2 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and wait 2 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A334921E03
3.188,1.927 4.563,2.271 1.375,0.344 10 false Air Fuel Ratio Sensor (for Bank 1 Sensor 1) 1.313,5.781 1.792,5.979 0.479,0.198 10 false Battery 1.156,4.604 1.521,4.771 0.365,0.167 10 false P/I-B 1.104,3.625 2.594,3.948 1.49,0.323 10 false NO. 1 Integration Relay 0.76,3.417 0.896,3.594 0.135,0.177 10 false 1 0.969,3.448 1.177,3.604 0.208,0.156 10 false 1E 1.125,3.083 1.396,3.26 0.271,0.177 10 false EFI 1.406,2.542 2.063,2.708 0.656,0.167 10 false EFI MAIN 0.958,0.917 1.229,1.083 0.271,0.167 10 false A/F 1.604,1.375 1.875,1.542 0.271,0.167 10 false A/F 2.344,0.802 2.563,0.969 0.219,0.167 10 false 1D 2.344,1.083 2.563,1.25 0.219,0.167 10 false 1D 2.344,2.24 2.563,2.406 0.219,0.167 10 false 1D 2.344,2.833 2.563,3 0.219,0.167 10 false 1D 2.396,0.615 2.51,0.792 0.115,0.177 10 false 8 2.396,1.229 2.51,1.406 0.115,0.177 10 false 7 2.396,2.042 2.51,2.219 0.115,0.177 10 false 2 2.396,2.625 2.51,2.802 0.115,0.177 10 false 3 3.188,1.771 3.469,1.938 0.281,0.167 10 false B26 3.042,4.802 4.417,5.146 1.375,0.344 10 false Air Fuel Ratio Sensor (for Bank 2 Sensor 1) 3.042,4.646 3.323,4.813 0.281,0.167 10 false B27 3.365,0.677 3.479,0.854 0.115,0.177 10 false 2 4.396,0.677 4.51,0.854 0.115,0.177 10 false 1 3.365,1.458 3.479,1.635 0.115,0.177 10 false 4 4.396,1.458 4.51,1.635 0.115,0.177 10 false 3 3.542,0.667 3.771,0.833 0.229,0.167 10 false +B 3.948,0.667 4.375,0.823 0.427,0.156 10 false HA1A 3.542,1.438 3.885,1.604 0.344,0.167 10 false A1A- 3.958,1.438 4.365,1.594 0.406,0.156 10 false A1A+ 3.188,3.573 3.302,3.75 0.115,0.177 10 false 2 4.219,3.573 4.333,3.75 0.115,0.177 10 false 1 3.188,4.365 3.302,4.542 0.115,0.177 10 false 4 4.219,4.365 4.333,4.542 0.115,0.177 10 false 3 3.365,3.573 3.594,3.74 0.229,0.167 10 false +B 3.771,3.573 4.198,3.729 0.427,0.156 10 false HA2A 3.365,4.344 3.708,4.51 0.344,0.167 10 false A2A- 3.781,4.344 4.188,4.5 0.406,0.156 10 false A2A+ 5.208,0.604 5.406,0.781 0.198,0.177 10 false 17 5.177,0.802 5.469,0.979 0.292,0.177 10 false B39 5.479,0.688 5.885,0.854 0.406,0.167 10 false HA1A 5.25,1.385 5.406,1.563 0.156,0.177 10 false 1 5.177,1.583 5.469,1.76 0.292,0.177 10 false B38 5.479,1.469 5.885,1.635 0.406,0.167 10 false A1A+ 5.25,2.438 5.406,2.615 0.156,0.177 10 false 2 5.177,2.646 5.469,2.823 0.292,0.177 10 false B38 5.25,3.063 5.406,3.24 0.156,0.177 10 false 9 5.177,3.271 5.469,3.448 0.292,0.177 10 false F51 5.479,2.531 5.885,2.698 0.406,0.167 10 false A1A- 5.25,4.271 5.406,4.448 0.156,0.177 10 false 7 5.177,4.479 5.469,4.656 0.292,0.177 10 false B38 5.479,4.365 5.885,4.531 0.406,0.167 10 false A2A+ 5.25,5.438 5.406,5.615 0.156,0.177 10 false 8 5.177,5.646 5.469,5.823 0.292,0.177 10 false B38 5.479,5.521 5.885,5.688 0.406,0.167 10 false A2A- 5.208,3.49 5.406,3.667 0.198,0.177 10 false 19 5.177,3.698 5.469,3.875 0.292,0.177 10 false B39 5.479,3.573 5.885,3.74 0.406,0.167 10 false HA2A 5.927,6.167 6.281,6.333 0.354,0.167 10 false ECM 5.49,3.156 5.917,3.323 0.427,0.167 10 false MREL 4.719,4.125 4.813,4.271 0.094,0.146 10 false * 4.823,1.229 4.917,1.375 0.094,0.146 10 false * 1.542,6.49 2.281,6.667 0.74,0.177 10 false *: Shielded

CAUTION / NOTICE / HINT

HINT:
·

Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.



HINT:

GTS only:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.


The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

(a) Connect the GTS to the DLC3.

(b) Start the engine and turn the GTS on.

(c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

(d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

(e) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

(f) Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.


HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.


·

The sensors react in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio sensor)
+25% Rich Below 3.1
-12.5% Lean Higher than 3.4
O2S B1S2
(Heated oxygen sensor)
+25% Rich Higher than 0.55
-12.5% Lean Below 0.4
AFS Voltage B2S1
(Air fuel ratio sensor)
+25% Rich Below 3.1
-12.5% Lean Higher than 3.4
O2S B2S2
(Heated oxygen sensor)
+25% Rich Higher than 0.55
-12.5% Lean Below 0.4


NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E82
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.542,1.604 1.99,1.792 0.448,0.188 8 false +25% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.146 6.885,6.573 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leak from exhaust system (Air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.479,3.688 1.927,3.875 0.448,0.188 8 false +25% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +25% 4.063,3.667 4.51,3.854 0.448,0.188 8 false +25% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.427,5.76 1.875,5.948 0.448,0.188 8 false +25% 1.438,7.781 1.885,7.969 0.448,0.188 8 false +25% 4.083,7.792 4.531,7.979 0.448,0.188 8 false +25% 4.104,5.74 4.552,5.927 0.448,0.188 8 false +25% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the output voltages of both the air fuel ratio and heated oxygen sensors.

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 or AFS Voltage B2S1, and O2S B1S2 or O2S B2S2. Then press the graph button on the Data List display.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
B26-1 (HA1A) - B39-17 (HA1A) Always Below 1 Ω
B26-3 (A1A+) - B38-1 (A1A+) Always Below 1 Ω
B26-4 (A1A-) - B38-2 (A1A-) Always Below 1 Ω
B27-1 (HA2A) - B39-19 (HA2A) Always Below 1 Ω
B27-3 (A2A+) - B38-7 (A2A+) Always Below 1 Ω
B27-4 (A2A-) - B38-8 (A2A-) Always Below 1 Ω
B26-1 (HA1A) or B39-17 (HA1A) - Body ground Always 10 kΩ or higher
B26-3 (A1A+) or B38-1 (A1A+) - Body ground Always 10 kΩ or higher
B26-4 (A1A-) or B38-2 (A1A-) - Body ground Always 10 kΩ or higher
B27-1 (HA2A) or B39-19 (HA2A) - Body ground Always 10 kΩ or higher
B27-3 (A2A+) or B38-7 (A2A+) - Body ground Always 10 kΩ or higher
B27-4 (A2A-) or B38-8 (A2A-) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the air fuel ratio sensor connector.



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

3.PERFORM CONFIRMATION DRIVING PATTERN
3.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to Confirmation Driving Pattern.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code / Pending.


d.

Read pending DTCs.

Result
Display (DTC Output) Proceed to
No output A
P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 B



A

END

B