| Vehicle Speed
|
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
|
Actual vehicle speed
|
Speed indicated on the speedometer.
|
| Engine Speed
|
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
|
690 to 790 rpm: Idling
|
-
|
| Calculate Load
|
Load calculated by ECM/
Min.: 0%, Max.: 100%
|
·
10 to 18.9%: Driving without load (2500 rpm)
|
-
|
| Vehicle Load
|
Vehicle load/
Min.: 0%, Max.: 25700%
|
Actual vehicle load
|
-
|
| MAF
|
Air flow rate from mass air flow meter/
Min.: 0 g/sec., Max.: 655.35 g/sec.
|
2.5 to 4.7 g/sec.: Idling
|
If the value is approximately 0.0 g/sec.:
·
Mass air flow meter power source circuit is open or shorted.
·
VG circuit is open or shorted.
If the value is 160.0 g/sec. or more:
|
| Atmosphere Pressure
|
Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
|
Equivalent to atmospheric pressure (absolute pressure)
|
-
|
| Coolant Temp
|
Engine coolant temperature:
Min.: -40°C, Max.: 140°C
|
80 to 100°C (176 to 212°F): After warming up
|
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
|
| Intake Air
|
Intake air temperature/
Min.: -40°C, Max.: 140°C
|
Equivalent to ambient air temperature
|
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
|
| Ambient Temperature
|
Ambient temperature/
Min.: -40°C, Max.: 215°C
|
Equivalent to ambient air temperature: Ignition switch ON
|
-
|
| Engine Run Time
|
Engine run time/
Min.: 0 seconds, Max.: 65535 seconds
|
Time after engine start
|
Service data.
|
| Initial Engine Coolant Temp
|
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
|
Close to ambient air temperature
|
Service data.
|
| Initial Intake Air Temp
|
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
|
Close to ambient air temperature
|
Service data.
|
| Battery Voltage
|
Battery voltage/
Min.: 0 V, Max.: 65.535 V
|
11 to 14 V: Idling
|
-
|
| Accelerator Position
|
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
|
Actual accelerator pedal position
|
-
|
| Accel Sens. No.1 Volt %
|
Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
|
·
10 to 22%: Accelerator pedal released
·
54 to 86%: Accelerator pedal fully depressed
|
-
|
| Accel Sens. No.2 Volt %
|
Absolute APP No. 2/
Min.: 0%, Max.: 100%
|
·
12 to 42%: Accelerator pedal released
·
66 to 98%: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No.1
|
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal released
·
2.6 to 4.5 V: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No.2
|
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
|
·
1.2 to 2.0 V: Accelerator pedal released
·
3.4 to 4.7 V: Accelerator pedal fully depressed
|
-
|
| Accelerator Idle Position
|
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
|
ON: Idling
|
-
|
| Accel Fully Close Learn #1
|
Accelerator fully closed learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
|
-
|
ETCS service data.
|
| Accel Fully Close Learn #2
|
Accelerator fully closed learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
|
-
|
ETCS service data.
|
| Throttle Sensor Volt %
|
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
|
·
10 to 22%: Throttle fully closed
·
64 to 96%: Throttle fully open
|
The calculated value based on VTA1.
|
| Throttl Sensor #2 Volt %
|
Throttle position sensor #2/
Min.: 0%, Max.: 100%
|
·
42 to 62%: Throttle fully closed
·
92 to 100%: Throttle fully open
|
The calculated value based on VTA2.
|
| ST1
|
Brake pedal signal/
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| System Guard
|
System guard/
ON or OFF
|
-
|
ETCS service data.
|
| Open Side Malfunction
|
Open side malfunction/
ON or OFF
|
-
|
ETCS service data.
|
| Throttle Idle Position
|
Whether or not throttle position sensor detecting idle/
ON or OFF
|
·
ON: Accelerator pedal released
·
OFF: Accelerator pedal depressed
|
-
|
| Throttle Require Position
|
Required throttle position/
Min.: 0 V, Max.: 4.98 V
|
0.5 to 1.1 V: Idling
|
-
|
| Throttle Sensor Position*
|
Throttle sensor position/
Min.: 0%, Max.: 100%
|
·
0%: Throttle fully closed
·
50 to 80%: Throttle fully open
|
Recognition value of the throttle opening angle in the ECM.
|
| Throttle Position No. 1
|
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal released
·
3.2 to 4.8 V: Accelerator pedal fully depressed
·
0.6 to 1.4 V: Fail-safe operating
|
-
|
| Throttle Position No. 2
|
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
|
·
2.1 to 3.1 V: Accelerator pedal released
·
4.6 to 5.0 V: Accelerator pedal fully depressed
·
2.1 to 3.1 V: Fail-safe operating
|
-
|
| Throttle Position Command
|
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
|
0.5 to 4.8 V
|
-
|
| Throttle Sens Open Pos #1
|
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
|
0.6 to 1.4 V
|
ETCS service data.
|
| Throttle Sens Open Pos #2
|
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
|
1.7 to 2.5 V
|
ETCS service data.
|
| Throttle Motor Current
|
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
|
0 to 3.0 A: Idling
|
ETCS service data.
|
| Throttle Motor DUTY
|
Throttle actuator/
Min.: 0%, Max.: 100%
|
0.5 to 40%: Idling
|
ETCS service data.
|
| Throttle Motor Duty (Open)
|
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
|
0 to 40%: Idling
|
ETCS service data.
|
| Throttle Motor Duty (Close)
|
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
|
0 to 40%: Idling
|
ETCS service data.
|
| Throttle Fully Close Learn
|
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
|
0.4 to 1.0 V: Accelerator pedal released
|
-
|
| +BM Voltage
|
+BM voltage/
Min.: 0 V, Max.: 79.998 V
|
11 to 14 V: Ignition switch ON and system normal
|
ETCS service data.
|
| Actuator Power Supply
|
Actuator power supply/
ON or OFF
|
ON: Idling
|
ETCS service data.
|
| Throttle Position
|
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Flow
|
Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Position
|
Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Feedback Value
|
ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Learning Value
|
ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Electric Load Feedback Val
|
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Air Conditioner FB Val
|
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| PS Feedback Val
|
Compensation flow rate according to power steering load/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Low Revolution Control
|
Low engine speed control operation state/
ON or OFF
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Neutral Control
|
Neutral control operation state/
ON or OFF
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| N Range Status
|
Shift lever N status/
ON or OFF
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Eng Stall Control FB Flow
|
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Deposit Loss Flow
|
Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Injector (Port)
|
Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
|
1600 to 2400 μs: Idling
|
-
|
| Injection Volum (Cylinder 1)
|
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
|
0 to 0.5 ml
|
Fuel injection volume of 10 injections.
|
| Fuel Pump/Speed Status
|
Fuel pump status/
ON or OFF
|
-
|
Active Test support data.
|
| EVAP (Purge) VSV
|
Purge VSV control duty/
Min.: 0%, Max.: 100%
|
0 to 100%: During idling
|
Command signal from the ECM.
|
| Evap Purge Flow
|
Purge flow/
Min.: 0%, Max.: 399.9%
|
0 to 100%: Idling
|
-
|
| Purge Density Learn Value
|
Purge density learned value/
Min.: -200, Max.: 199.993
|
Idling: -40 to 0
|
Service data.
|
| Vapor Pressure (calculated)
|
Calculated EVAP system pressure/
Min.: -720.896 kPa (-5407.167 mmHg), Max.: 720.874 kPa (5407.002 mmHg)
|
Approximately 100 kPa (750 mmHg): Ignition switch ON
|
-
|
| EVAP Purge VSV
|
VSV status for EVAP control/
ON or OFF
|
-
|
Active Test support data.
|
| Purge Cut VSV Duty
|
Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| Target Air-Fuel Ratio
|
Target air fuel ratio/
Min.: 0, Max.: 1.99
|
0.8 to 1.2: During idling
|
-
|
| AF Lambda B1S1
|
Short-term fuel trim associated with the Bank 1 Sensor 1/
Min.: 0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean
|
-
|
| AF Lambda B2S1
|
Short-term fuel trim associated with the Bank 2 Sensor 1/
Min.: 0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean
|
-
|
| AFS Voltage B1S1
|
Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
|
2.8 to 3.8 V: Idling
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| AFS Voltage B2S1
|
Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
|
2.8 to 3.8 V: Idling
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| AFS Current B1S1
|
Air fuel ratio sensor current (for Bank 1 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
|
-0.5 to 0.5 mA: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
|
| AFS Current B2S1
|
Air fuel ratio sensor current (for Bank 2 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
|
-0.5 to 0.5 mA: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
|
| A/F Heater Duty #1
|
Air fuel ratio sensor heater duty ratio (for Bank 1)/
Min.: 0%, Max.: 399.9%
|
0 to 100%
|
-
|
| A/F Heater Duty #2
|
Air fuel ratio sensor heater duty ratio (for Bank 2)/
Min.: 0%, Max.: 399.9%
|
0 to 100%
|
-
|
| O2S B1S2
|
Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
|
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| O2S B2S2
|
Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
|
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
|
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
|
| O2S Impedance B1S2
|
Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/
Min.: 0 Ω, Max.: 21247.67 Ω
|
5 to 15000 Ω
|
After driving approx. 10 min. in an urban area.
|
| O2S Impedance B2S2
|
Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/
Min.: 0 Ω, Max.: 21247.67 Ω
|
5 to 15000 Ω
|
After driving approx. 10 min. in an urban area.
|
| O2 Heater B1S2
|
Heated oxygen sensor heater (for Bank 1 Sensor 2)/
Active or Not Act
|
-
|
-
|
| O2 Heater B2S2
|
Heated oxygen sensor heater (for Bank 2 Sensor 2)/
Active or Not Act
|
-
|
-
|
| O2 Heater Curr Val B1S2
|
Heated oxygen sensor current (for Bank 1 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
|
-
|
-
|
| O2 Heater Curr Val B2S2
|
Heated oxygen sensor current (for Bank 2 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
|
-
|
-
|
| Short FT #1
|
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
|
| Long FT #1
|
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
|
| Total FT #1
|
Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
|
-0.2 to 0.2: Idling
|
-
|
| Short FT #2
|
Short-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
|
| Long FT #2
|
Long-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
|
-20 to +20%
|
This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
|
| Total FT #2
|
Total fuel trim of bank 2/
Min.: -0.5, Max.: 0.496
|
-0.2 to 0.2: Idling
|
-
|
| Fuel System Status #1
|
Fuel system status (Bank 1)/
OL, CL, OL Drive, OL Fault or CL Fault
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
·
CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
·
OL Drive: Open loop due to driving conditions (fuel enrichment).
·
OL Fault: Open loop due to a detected system fault.
·
CL Fault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
|
| Fuel System Status #2
|
Fuel system status (Bank 2)/
OL, CL, OL Drive, OL Fault or CL Fault
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
·
CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
·
OL Drive: Open loop due to driving conditions (fuel enrichment).
·
OL Fault: Open loop due to a detected system fault.
·
CL Fault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
|
| IGN Advance
|
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
|
BTDC 7 to 24°: Idling
|
-
|
| Knock Feedback Value
|
Knocking feedback value/
Min.: -1024° CA, Max.: 1023.9° CA
|
-3° CA:
Driving at 70 km/h (44 mph)
|
Service data.
|
| Knock Correct Learn Value
|
Knocking correction learned value/
Min.: -1024° CA, Max.: 1023.9° CA
|
5 to 28° CA:
Driving at 70 km/h (44 mph)
|
Service data.
|
| Idle Spark Advn Ctrl #1
|
Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0° CA, Max.: 15.93° CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #2
|
Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0° CA, Max.: 15.93° CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #3
|
Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0° CA, Max.: 15.93° CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #4
|
Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0° CA, Max.: 15.93° CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #5
|
Individual cylinder timing advance compensation amount (No. 5)/
Min.: 0° CA, Max.: 15.93° CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #6
|
Individual cylinder timing advance compensation amount (No. 6)/
Min.: 0° CA, Max.: 15.93° CA
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| VVT Control Status #1
|
Variable valve timing (VVT) control status (Bank 1)/
ON or OFF
|
-
|
Active Test support data.
|
| VVT Control Status #2
|
VVT control status (Bank 2)/
ON or OFF
|
-
|
Active Test support data.
|
| VVT Advance Fail
|
VVT control failure status/
ON or OFF
|
ON: VVT control failure
|
-
|
| VVT Aim Angle #1
|
VVT target duty (Bank 1)/
Min.: 0%, Max.: 399.9%
|
0%: Idling
|
VVT duty signal value during forced operation.
|
| VVT Change Angle #1
|
VVT displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
0 to 5 DegFR: Idling
|
Displacement angle during forced operation.
|
| VVT OCV Duty #1
|
Camshaft timing oil control valve operation duty (for Intake Side of Bank 1)/
Min.: 0%, Max.: 399.9%
|
0%: Idling
|
Requested duty value for forced operation.
|
| VVT Aim Angle #2
|
VVT target duty (Bank 2)/
Min.: 0%, Max.: 399.9%
|
0%: Idling
|
VVT duty signal value during forced operation.
|
| VVT Change Angle #2
|
VVT displacement angle (for Intake Side of Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
0 to 5 DegFR: Idling
|
Displacement angle during forced operation.
|
| VVT OCV Duty #2
|
Camshaft timing oil control valve operation duty (Bank 2)/
Min.: 0%, Max.: 399.9%
|
0%: Idling
|
Requested duty value for forced operation.
|
| VVT Ex Hold Lrn Val #1
|
VVT exhaust hold duty ratio learned value (Bank 1)/
Min.: 0%, Max.: 399.9%
|
0 to 80%: Idling
|
-
|
| VVT Ex Chg Angle #1
|
VVT exhaust displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
0 to 40 DegFR: Idling
|
Displacement angle during forced operation.
|
| VVT Ex OCV Duty #1
|
Camshaft timing oil control valve duty (for Exhaust Side of Bank 1)/
Min.: 0%, Max.: 399.9%
|
0 to 100%: Idling
|
Requested duty value for forced operation.
|
| VVT Ex Hold Lrn Val #2
|
VVT exhaust hold duty ratio learned value (Bank 2)/
Min.: 0%, Max.: 399.9%
|
0 to 80%: Idling
|
-
|
| VVT Ex Chg Angle #2
|
VVT exhaust displacement angle (Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
|
0 to 40 DegFR: Idling
|
Displacement angle during forced operation.
|
| VVT Ex OCV Duty #2
|
Camshaft timing oil control valve duty (for Exhaust Side of Bank 2)/
Min.: 0%, Max.: 399.9%
|
0 to 100%: Idling
|
Requested duty value for forced operation.
|
| VN Turbo Type
|
VN turbo type/
Not Avl, Commo, Vacuum or CAN Com
|
Not Avl
|
-
|
| Catalyst Temp B1S1
|
Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Catalyst Temp B2S1
|
Catalyst temperature (Bank 2, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Catalyst Temp B1S2
|
Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Catalyst Temp B2S2
|
Catalyst temperature (Bank 2, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
|
-
|
-
|
| Starter Signal
|
Starter signal/
Close or Open
|
Open: Cranking
|
-
|
| Power Steering Signal
|
Power steering oil pressure switch signal/ ON or OFF
|
ON: Power steering operating
|
-
|
| Neutral Position SW Signal
|
PNP switch status/
ON or OFF
|
ON: P or N position
|
-
|
| Transfer Neutral
|
Neutral status of the transfer/
ON or OFF
|
ON: 4WD control switch in 2WD position
|
-
|
| 4WD SW
|
4WD switch status/
ON or OFF
|
ON: Vehicle in 4WD (part-time 4WD vehicle)
|
-
|
| Transfer L4
|
L4 status of the transfer/
ON or OFF
|
ON: 4WD control switch in 4L position
|
-
|
| Stop Light Switch
|
Stop light switch/
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| A/C Signal
|
A/C switch status/
ON or OFF
|
ON: A/C on
|
-
|
| Closed Throttle Position SW
|
Closed throttle position switch/
ON or OFF
|
·
ON: Throttle fully closed
|
-
|
| Fuel Cut Condition
|
Fuel cut condition/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Immobiliser Communication
|
Immobiliser communication/
ON or OFF
|
ON: Normal
|
-
|
| Check Mode
|
Check mode/
ON or OFF
|
ON: Check mode on
|
Refer to Check Mode Procedure (See page ( )).
|
| SPD Test Result
|
Check mode result for vehicle speed sensor/
Compl or Incmpl
|
-
|
-
|
| Misfire Test Result
|
Check mode result for misfire monitor/
Compl or Incmpl
|
-
|
-
|
| OXS1 Test Result
|
Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
|
-
|
-
|
| OXS2 Test Result
|
Check mode result for heated oxygen sensor (Bank 2)/
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #2
|
Check mode result for air fuel ratio sensor (Bank 2)/
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #1
|
Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
|
-
|
-
|
| Complete Parts Monitor
|
Comprehensive component monitor/
Not Avl or Avail
|
-
|
-
|
| Fuel System Monitor
|
Fuel system monitor/
Not Avl or Avail
|
-
|
-
|
| Misfire Monitor
|
Misfire monitor/
Not Avl or Avail
|
-
|
-
|
| EGR/VVT Monitor
|
EGR/VVT monitor/
Not Avl or Avail
|
-
|
-
|
| EGR/VVT Monitor
|
EGR/VVT monitor/
Compl or Incmpl
|
-
|
-
|
| O2S(A/FS) Heater Monitor
|
O2S (A/FS) heater monitor/
Not Avl or Avail
|
-
|
-
|
| O2S(A/FS) Heater Monitor
|
O2S (A/FS) heater monitor/
Compl or Incmpl
|
-
|
-
|
| O2S(A/FS) Monitor
|
O2S (A/FS) monitor/
Not Avl or Avail
|
-
|
-
|
| O2S(A/FS) Monitor
|
O2S (A/FS) monitor/
Compl or Incmpl
|
-
|
-
|
| A/C Monitor
|
A/C monitor/
Not Avl or Avail
|
-
|
-
|
| A/C Monitor
|
A/C monitor/
Compl or Incmpl
|
-
|
-
|
| 2nd Air Monitor
|
2nd air monitor/
Not Avl or Avail
|
-
|
-
|
| 2nd Air Monitor
|
2nd air monitor/
Compl or Incmpl
|
-
|
-
|
| EVAP Monitor
|
EVAP monitor/
Not Avl or Avail
|
-
|
-
|
| EVAP Monitor
|
EVAP monitor/
Compl or Incmpl
|
-
|
-
|
| Heated Catalyst Monitor
|
Heated catalyst monitor/
Not Avl or Avail
|
-
|
-
|
| Heated Catalyst Monitor
|
Heated catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor/
Not Avl or Avail
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| Component Monitor ENA
|
Comprehensive component monitor/
Unable or Enable
|
-
|
-
|
| Component Monitor CMPL
|
Comprehensive component monitor/
Compl or Incmpl
|
-
|
-
|
| Fuel System Monitor ENA
|
Fuel system monitor/
Unable or Enable
|
-
|
-
|
| Fuel System Monitor CMPL
|
Fuel system monitor/
Compl or Incmpl
|
-
|
-
|
| Misfire Monitor ENA
|
Misfire monitor/
Unable or Enable
|
-
|
-
|
| Misfire Monitor CMPL
|
Misfire monitor/
Compl or Incmpl
|
-
|
-
|
| EGR/VVT Monitor ENA
|
EGR monitor/
Unable or Enable
|
-
|
-
|
| EGR/VVT Monitor CMPL
|
EGR monitor/
Compl or Incmpl
|
-
|
-
|
| Heater Monitor ENA
|
O2S (A/FS) heater monitor/
Unable or Enable
|
-
|
-
|
| Heater Monitor CMPL
|
O2S (A/FS) heater monitor/
Compl or Incmpl
|
-
|
-
|
| O2S(A/FS) Monitor ENA
|
O2S (A/FS) monitor/
Unable or Enable
|
-
|
-
|
| O2S(A/FS) Monitor CMPL
|
O2S (A/FS) monitor/
Compl or Incmpl
|
-
|
-
|
| A/C Monitor ENA
|
A/C monitor/
Unable or Enable
|
-
|
-
|
| A/C Monitor CMPL
|
A/C monitor/
Compl or Incmpl
|
-
|
-
|
| 2nd Air Monitor ENA
|
2nd air monitor/
Unable or Enable
|
-
|
-
|
| 2nd Air Monitor CMPL
|
2nd air monitor/
Compl or Incmpl
|
-
|
-
|
| EVAP Monitor ENA
|
EVAP monitor/
Unable or Enable
|
-
|
-
|
| EVAP Monitor CMPL
|
EVAP monitor/
Compl or Incmpl
|
-
|
-
|
| Heated Cat Monitor ENA
|
Heated catalyst monitor/
Unable or Enable
|
-
|
-
|
| Heated Cat Monitor CMPL
|
Heated catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| Catalyst Monitor ENA
|
Catalyst monitor/
Unable or Enable
|
-
|
-
|
| Catalyst Monitor CMPL
|
Catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| TC Terminal
|
TC terminal status/
ON or OFF
|
-
|
-
|
| # Codes (Include History)
|
Number of codes/
Min.: 0, Max.: 255
|
-
|
Number of DTCs stored.
|
| MIL
|
MIL status/
ON or OFF
|
ON: MIL on
|
-
|
| MIL ON Run Distance
|
Distance driven with MIL on/
Min.: 0 km, Max.: 65535 km
|
Distance driven after DTC stored
|
-
|
| Running Time from MIL ON
|
Running time from MIL ON/
Min.: 0 minutes, Max.: 65535 minutes
|
Running time after MIL turned on
|
-
|
| Time after DTC Cleared
|
Time after DTCs cleared/
Min.: 0 minutes, Max.: 65535 minutes
|
Time after DTCs cleared
|
-
|
| Distance from DTC Cleared
|
Distance after DTCs cleared/
Min.: 0 km, Max.: 65535 km
|
Driving distance after DTCs cleared
|
-
|
| Warmup Cycle Cleared DTC
|
Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
|
-
|
Number of warmup cycles after the DTCs are cleared.
|
| Dist Batt Cable Disconnect
|
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
|
Total distance vehicle driven after battery cable disconnected
|
-
|
| OBD Requirements
|
OBD requirement
|
OBD2
|
-
|
| Number of Emission DTC
|
Emissions-related DTCs
|
-
|
Number of emissions-related DTCs.
|
| TC and TE1
|
TC and CG (TE1) terminals of DLC3/
ON or OFF
|
-
|
-
|
| Ignition Trig. Count
|
Ignition counter/
Min.: 0, Max.: 65535
|
0 to 800
|
-
|
Cylinder #1 Misfire Count
to
Cylinder #6 Misfire Count
|
Misfire ratio of cylinder 1 to 6/
Min.: 0, Max.: 255
|
0
|
-
|
| All Cylinders Misfire Count
|
Misfire count of all cylinders/
Min.: 0, Max.: 255
|
0 to 35
|
-
|
| Misfire RPM
|
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
|
0 rpm: Misfire 0
|
-
|
| Misfire Load
|
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
|
0 g/rev: Misfire 0
|
-
|
| Misfire Margin
|
Misfire monitoring/
Min.: -128%, Max.: 127%
|
-100 to 99.2%
|
Misfire detection margin.
|
| Catalyst OT MF F/C
|
Fuel cut to prevent misfire causing catalyst overheating/
Not Avl or Avail
|
·
Avail: Fuel cut to prevent misfire causing catalyst overheating available
·
Not Avl: Fuel cut to prevent misfire causing catalyst overheating not available
|
-
|
| Cat OT MF F/C History
|
History of fuel cut to prevent misfire causing catalyst overheating/
ON or OFF
|
ON: Fuel cut operation history exists
|
-
|
| Cat OT MF F/C Cylinder #1
|
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #2
|
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #3
|
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #4
|
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #5
|
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Cat OT MF F/C Cylinder #6
|
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
|
ON: Fuel cut operating
|
-
|
| Engine Speed (Starter Off)
|
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Starter Count
|
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Run Dist of Previous Trip
|
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Starting Time
|
Time elapsed after engine started (interval between ignition switch ON and off)/
Min.: 0 ms, Max.: 655350 ms
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Coolant Temp
|
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Intake Temp
|
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Oil Temperature
|
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Eng Oil Temp
|
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Ambient Temp for A/C
|
Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Ambient Temp
|
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Start Hesitation
|
History of hesitation during engine start/
ON or OFF
|
-
|
-
|
| Low Rev for Eng Start
|
History of low engine speed after engine start/
ON or OFF
|
-
|
-
|
| Minimum Engine Speed
|
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
For use when engine stall, starting problems or rough idle is present.
|
| Power Steering Pressure
|
Power steering oil pressure/
Min.: 0 MPa, Max.: 25.599 MPa
|
-
|
-
|
| ACT VSV
|
A/C cut status for Active Test/
ON or OFF
|
-
|
Active Test support data.
|
| Idle Fuel Cut Prohibit
|
Prohibition of fuel cut at idle/
ON or OFF
|
-
|
-
|
| Idle Fuel Cut
|
Fuel cut at idle/
ON or OFF
|
ON: Fuel cut operating
|
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
|
| FC TAU
|
Fuel cut TAU (fuel cut during very light load)/
ON or OFF
|
ON: Fuel cut operating
|
The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete.
|
| Immobiliser Fuel Cut
|
Status of the immobiliser fuel cut/
ON or OFF
|
-
|
-
|
| Comm with Power Manage
|
Status of the communication with power management control ECU/
Comm or No Comm
|
-
|
-
|
| Comm with Air Conditioner
|
Status of the communication with air conditioning amplifier/
Comm or No Comm
|
-
|
-
|
| Electrical Load Signal 2
|
Electrical load signal/
ON or OFF
|
-
|
-
|
| Model Code
|
Model code
|
-
|
Used for identifying the model code:
GRN28#
|
| Engine Type
|
Engine type
|
-
|
Used for identifying the engine type:
1GRFE
|
| Cylinder Number
|
Number of cylinders/
Min.: 0, Max.: 255
|
-
|
Used for identifying the number of cylinders:
6
|
| Transmission Type
|
Transmission type
|
-
|
Used for identifying the transmission type:
ECT 5th
|
| Destination
|
Destination
|
-
|
Used for identifying the destination:
A
|
| Model Year
|
Model year/
Min.: 1900, Max.: 2155
|
-
|
Used for identifying the model year:
20##
|
| System Identification
|
System identification
|
-
|
Used for identifying the engine system:
Gasoline (gasoline engine)
|
| Engine Speed of Cyl #1
|
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #2
|
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #3
|
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #4
|
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #5
|
Engine speed for cylinder 5/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Engine Speed of Cyl #6
|
Engine speed for cylinder 6/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| Av Engine Speed of All Cyl
|
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression is performed using the Active Test.
|
| SPD (NT)
|
Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
|
Lock-up is:
·
Lock-up on (after warming up engine): Input turbine speed (NT) equal to engine speed
·
Lock-up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
|
Data is displayed in increments of 50 rpm.
|
| SPD (SP2)
|
Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
|
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
|
-
|
| Shift SW Status (P Range)
|
PNP switch status (P)/
ON or OFF
|
·
Shift lever not in P: OFF
|
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (R Range)
|
PNP switch status (R)/
ON or OFF
|
·
Shift lever not in R: OFF
|
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N Range)
|
PNP switch status (N)/
ON or OFF
|
·
Shift lever not in N: OFF
|
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Sports Shift Up SW
|
Sport shift up switch status/
ON or OFF
|
·
ON: Shift lever held in "+" (up-shift)
·
OFF: Shift lever not in "+" (up-shift)
|
-
|
| Sports Shift Down SW
|
Sport shift down switch status/
ON or OFF
|
·
ON: Shift lever held in "-" (down-shift)
·
OFF: Shift lever not in "-" (down-shift)
|
-
|
| Sports Mode Selection SW
|
Sport mode select switch status/
ON or OFF
|
·
ON: Shift lever in S, "+" or "-"
·
OFF: Shift lever not in S, "+" or "-"
|
-
|
| Shift SW Status (D Range)
|
PNP switch status (D)/
ON or OFF
|
·
Shift lever in D, S, "+" or "-": ON
·
Shift lever not in D, S, "+" or "-": OFF
|
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| A/T Oil Temperature 1
|
No. 1 ATF temperature sensor value/
Min.: -40°C, Max.: 215°C
|
·
After stall test:
Approximately 80°C (176°F)
·
Equal to ambient temperature when engine cold
|
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
|
| A/T Oil Temperature 2
|
No. 2 ATF temperature sensor value/
Min.: -40°C, Max.: 215°C
|
·
After stall test:
Approximately 80°C (176°F)
·
Equal to ambient temperature when engine cold
|
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
|
| Lock Up
|
Lock-up/
ON or OFF
|
·
Lock-up not operating: OFF
|
-
|
| Shift Status
|
ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
|
·
Shift lever in D: 1st, 2nd, 3rd, 4th or 5th
·
Shift lever in S: 1st, 2nd, 3rd, 4th or 5th
|
-
|
| SLT Solenoid Status
|
Shift solenoid SLT status/
ON or OFF
|
·
Accelerator pedal depressed: OFF
·
Accelerator pedal released: ON
|
-
|
| SLU Solenoid Status
|
Shift solenoid SLU status/
ON or OFF
|
·
Shift solenoid operating: ON
·
Shift solenoid not operating: OFF
|
-
|
| AT Fluid
|
Flex lock-up judder judgment/
ON or OFF
|
·
ON: Judder judgment occurs
·
OFF: Judder judgment does not occur
|
-
|