11101A
1.INSPECT CYLINDER HEAD SET BOLT
11101
2.INSPECT CYLINDER HEAD SUB-ASSEMBLY
11115
3.INSTALL CYLINDER HEAD GASKET
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.
Apply seal packing to a new cylinder head gasket as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.5 to 3.0 mm (0.0984 to 0.118 in.)
| A | 10 to 15 mm (0.394 to 0.591 in.) |
| B | 1.25 to 1.5 mm (0.0492 to 0.0591 in.) |
| *1 | Seal Packing |
| *2 | Gasket |
Remove any oil from the contact surface.
Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Do not add engine oil within 2 hours of installation.
Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.
Make sure that the gasket is installed facing the proper direction.
| *1 | Lot No. |
|
Engine Front |
11101
4.INSTALL CYLINDER HEAD SUB-ASSEMBLY
Place the cylinder head on the cylinder block.
Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
Make sure that no oil is on the mounting surface of the cylinder head.
The cylinder head bolts are tightened in 3 progressive steps.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1:
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.
Step 2:
Mark the front side of each cylinder head bolt head with paint.
Tighten the cylinder head bolts another 90°.
Step 3:
Tighten the cylinder head bolts an additional 90°.
Check that the paint mark is now at a 180° angle to the front.
Thoroughly wipe clean any seal packing.
11116
5.INSTALL NO. 2 CYLINDER HEAD GASKET
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.
Apply seal packing to a new cylinder head gasket as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.5 to 3.0 mm (0.0984 to 0.118 in.)
| A | 10 to 15 mm (0.394 to 0.591 in.) |
| B | 1.25 to 1.5 mm (0.0492 to 0.0591 in.) |
| *1 | Seal Packing |
| *2 | Gasket |
Remove any oil from the contact surface.
Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Do not add engine oil within 2 hours of installation.
Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.
Make sure that the gasket is installed facing the proper direction.
| *1 | Lot No. |
|
Engine Front |
11102
6.INSTALL CYLINDER HEAD LH
Place the cylinder head on the cylinder block.
Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
Make sure that no oil is on the mounting surface of the cylinder head.
The cylinder head bolts are tightened in 3 progressive steps.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1:
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.
Step 2:
Mark the front side of each cylinder head bolt head with paint.
Tighten the cylinder head bolts another 90°.
Step 3:
Tighten the cylinder head bolts an additional 90°.
Check that the paint mark is now at a 180° angle to the front.
Tighten the 2 bolts in the order shown in the illustration.
Thoroughly wipe clean any seal packing.
13716
7.INSTALL VALVE STEM CAP
13750
8.INSTALL VALVE LASH ADJUSTER ASSEMBLY
13801
9.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
10.INSTALL CAMSHAFT BEARING CAP (for Bank 2)
11.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
12.INSTALL CAMSHAFT BEARING CAP (for Bank 1)
13.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH
13560A
14.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
15.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)
13550
16.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
17.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)
13561
18.INSTALL NO. 1 CHAIN VIBRATION DAMPER
13562
19.INSTALL NO. 2 CHAIN VIBRATION DAMPER
13521
20.INSTALL CRANKSHAFT TIMING SPROCKET
13581
21.INSTALL NO. 1 IDLE GEAR SHAFT
13506
22.INSTALL CHAIN SUB-ASSEMBLY
13559
23.INSTALL CHAIN TENSIONER SLIPPER
13540
24.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
25.INSPECT VALVE TIMING
11302
26.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Install the timing chain cover (See page Engine / Hybrid System>1GR-FE LUBRICATION>OIL PUMP>INSTALLATION).