Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2014.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273880 CYLINDER HEAD GASKET A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.

Remove the timing chain cover sub-assembly (See page Engine / Hybrid System>1GR-FE LUBRICATION>OIL PUMP>REMOVAL).


Hide 13540 3.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 10.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

Hide 13550 11.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 14.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

Hide 13560A 15.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13801 18.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11101 21.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A221092E12
2.677,0.021 2.844,0.188 0.167,0.167 10 true 3 1.958,0.021 2.125,0.188 0.167,0.167 10 true 5 1.24,0.021 1.406,0.198 0.167,0.177 10 true 7 0.521,0.042 0.708,0.219 0.188,0.177 10 true 2 2.677,1.844 2.813,2 0.135,0.156 10 true 1 1.958,1.865 2.094,2.021 0.135,0.156 10 true 8 1.219,1.875 1.354,2.031 0.135,0.156 10 true 6 0.51,1.865 0.646,2.021 0.135,0.156 10 true 4

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

NOTICE:
·

Be careful not to drop washers into the cylinder head sub-assembly.

·

Cylinder head warpage or cracking could result from removing bolts in an incorrect order.



HINT:

Arrange the removed parts in the correct order.



b.

Remove the cylinder head sub-assembly.


Hide 11102 22.REMOVE CYLINDER HEAD LH

a.
A221093E01
0.04,0.446 0.174,0.602 0.133,0.156 10 2 0.02,1.065 0.154,1.221 0.133,0.156 10 1

Uniformly loosen and remove the 2 cylinder head set bolts in several steps in the sequence shown in the illustration.


b.
A221094E11
0.906,0.073 1.042,0.229 0.135,0.156 10 true 1 1.583,0.063 1.719,0.219 0.135,0.156 10 true 8 2.281,0.063 2.417,0.219 0.135,0.156 10 true 6 2.948,0.052 3.083,0.208 0.135,0.156 10 true 4 0.906,1.823 1.042,1.979 0.135,0.156 10 true 3 1.573,1.823 1.708,1.979 0.135,0.156 10 true 5 2.271,1.823 2.406,1.979 0.135,0.156 10 true 7 2.938,1.823 3.073,1.979 0.135,0.156 10 true 2

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

NOTICE:
·

Be careful not to drop washers into the cylinder head sub-assembly.

·

Cylinder head warpage or cracking could result from removing bolts in an incorrect order.



HINT:

Be sure to keep the removed parts for each installation position separate.



c.

Remove the cylinder head LH.


Hide 11115 23.REMOVE CYLINDER HEAD GASKET

Hide 11116 24.REMOVE NO. 2 CYLINDER HEAD GASKET