Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CYLINDER BLOCK
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273886 CYLINDER BLOCK A

1GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

a.

Install new stud bolts.

Torque:
for stud bolt A and C : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for stud bolt B and D : 4.0 N*m (41 kgf*cm, 35 in.*lbf)

A388847E01
0.417,0.344 0.729,0.542 0.313,0.198 10 false *A 3.906,0.125 4.219,0.323 0.313,0.198 10 false *B 0.396,2.375 0.708,2.573 0.313,0.198 10 false *C 3.833,2.781 4.146,2.979 0.313,0.198 10 false *D 1.031,1.792 1.344,1.99 0.313,0.198 10 false A 1.354,1.698 1.521,1.896 0.167,0.198 10 false A 3.927,1.167 4.094,1.365 0.167,0.198 10 false B 5.74,0.844 5.906,1.042 0.167,0.198 10 false B 0.104,4.083 0.417,4.281 0.313,0.198 10 false C 1.802,4.063 2.115,4.26 0.313,0.198 10 false C 4.542,4.188 4.854,4.385 0.313,0.198 10 false D 4.771,4.188 5.083,4.385 0.313,0.198 10 false D 2.521,1.875 2.969,2.052 0.448,0.177 10 false A (M8) 5.833,1.635 6.281,1.813 0.448,0.177 10 false B (M6) 2.531,4.313 2.979,4.49 0.448,0.177 10 false C (M8) 5.885,4.125 6.333,4.302 0.448,0.177 10 false D (M6) 2.969,1.219 3.531,1.583 0.563,0.365 10 false 52 mm (2.05 in.) 6.24,1.125 6.948,1.5 0.708,0.375 10 false 23 mm (0.906 in.) 2.958,3.469 3.667,3.844 0.708,0.375 10 false 56 mm (2.21 in.) 6.313,3.615 7.021,3.99 0.708,0.375 10 false 23 mm (0.906 in.)

Text in Illustration
*A Front Side *B Upper Side
*C Lower Side *D Rear Side


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A120734

Using a 5 mm hexagon socket wrench, install the 3 oil nozzles with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13101 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A221130

Using a screwdriver, install a new snap ring on one side of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



b.
P101024

Gradually heat the piston to approximately 80°C (176°F).


c.
A221131E07
2.469,0.375 2.885,0.208 2.885,0.208 3.031,0.208 true 3.063,0.125 3.26,0.313 0.198,0.188 10 false *1 0.729,1.792 0.927,1.979 0.198,0.188 10 false *1

Coat the piston pin with engine oil.


d.

Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

Text in Illustration
*1 Front Mark

HINT:

The piston and pin are a matched set.



e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


f.
A223711

Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 13011 4.INSTALL PISTON RING SET

a.

Install the oil ring (expander) and 2 side rails by hand.


b.
A221133E01
0.561,1.551 0.766,1.728 0.205,0.177 10 *1 0.678,1.226 0.678,1.531 false 0.643,2.813 0.847,2.990 0.205,0.177 10 *2 2.465,2.813 2.669,2.990 0.205,0.177 10 *3

Using a piston ring expander, install the 2 compression rings with the painted mark on the right side.

Text in Illustration
*1 Painted Mark
*2 No. 1 Compression Ring
*3 No. 2 Compression Ring
V100135

Right Side


c.
A388848E01
0.448,1.813 0.76,2.01 0.313,0.198 10 false *1 0.438,0.188 0.75,0.385 0.313,0.198 10 false *2 2.26,0.031 2.573,0.229 0.313,0.198 10 false *3 2.26,1.958 2.573,2.156 0.313,0.198 10 false *4 0.24,1 0.552,1.198 0.313,0.198 10 false *5 0.323,1.365 0.635,1.563 0.313,0.198 10 false *6

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Lower Side Rail
*4 Upper Side Rail
*5 Expander
*6 Front Mark


Hide 11711 5.INSTALL CRANKSHAFT BEARING

HINT:
A223696E13
0.563,1.854 1.208,2.052 0.646,0.198 10 false 19.9 mm 2.417,1.833 3.063,2.031 0.646,0.198 10 false 17.3 mm 0.719,0.135 0.927,0.333 0.208,0.198 10 false *1 2.542,0.146 2.75,0.344 0.208,0.198 10 false *2

Main bearings come in widths of 17.3 mm (0.681 in.) and 19.9 mm (0.783 in.). Install the 19.9 mm (0.783 in.) bearings in the No. 1 and No. 4 cylinder block journal positions with the bearing caps. Install the 17.3 mm (0.681 in.) bearings in the No. 2 and No. 3 positions.


Text in Illustration
*1 No. 1 and No. 4 Journal Bearings
*2 No. 2 and No. 3 Journal Bearings

a.

Clean each main journal and bearing.


b.

Install the upper bearing.

i.
A183116E02
1.63,3.528 1.825,3.73 0.195,0.203 10 *a 2.504,3.528 2.713,3.712 0.21,0.184 10 *b

Install the upper bearing to the cylinder block as shown in the illustration.

Text in Illustration
*a CORRECT
*b INCORRECT

NOTICE:
·

Do not apply engine oil to the bearings or contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the inner surface of the bearing.

·

If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.





c.
A183118E07
2.281,3.438 2.552,3.771 2.552,3.771 2.552,3.948 true 0.844,3.708 0.979,3.885 0.135,0.177 10 false A 2.021,3.708 2.156,3.885 0.135,0.177 10 false B 2.469,4 2.677,4.198 0.208,0.198 10 false *2 0.792,2.146 1.01,2.344 0.219,0.198 10 false *1

Install the lower bearing.

i.

Install the lower bearings to the crankshaft bearing caps.

Text in Illustration
*1 Mark 1, 2, 3 or 4
*2 Vernier Caliper


ii.

Using a vernier caliper, measure the distance between the edge of the crankshaft bearing cap and the edge of the lower bearing.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings or contact surfaces.

·

Do not allow coolant to come into contact with the inner surface of the bearing.

·

If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.





Hide 13411 6.INSTALL CRANKSHAFT

NOTICE:

Clean the contact surface of each main journal and crank pin.


a.

Apply new engine oil to the upper bearing and install the crankshaft to the cylinder block.


b.
A229670

Push the crankshaft in the rear thrust direction to create clearance and install a thrust washer to the No. 2 journal position with the oil groove facing the front of the engine.


c.

Push the crankshaft in the forward thrust direction to create clearance and install a thrust washer to the No. 2 journal position with the oil groove facing the rear of the engine.


d.
A229671

Install the 2 lower thrust washers to the No. 2 bearing cap with the grooves facing outward.


e.
A221135

Examine the front marks and numbers and set the crankshaft bearing caps on the cylinder block.


f.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.


g.

Temporarily install the 8 crankshaft bearing cap bolts to the inside positions.


h.
A221136E02
0.781,1.594 0.958,1.781 0.177,0.188 10 false *a

Tighten the 2 bolts for each bearing cap until the clearance between the crankshaft bearing cap and the cylinder block becomes less than 6 mm (0.236 in.).

Text in Illustration
*a Less than 6 mm


i.
A388849

Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


j.
U147494

Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts and temporarily install the 8 crankshaft bearing bolts to the outside positions.


k.

Tighten the crankshaft bearing cap bolts.

HINT:

The cap bolts are tightened in 2 progressive steps.


i.
A388850E01
2.063,0.771 2.219,0.969 0.156,0.198 10 false 1 1.542,1.01 1.698,1.208 0.156,0.198 10 false 2 1,1.302 1.156,1.5 0.156,0.198 10 false 3 1.177,1.333 1.333,1.531 0.156,0.198 10 false 4 2.458,0.375 2.615,0.573 0.156,0.198 10 false 5 2.708,0.5 2.865,0.698 0.156,0.198 10 false 6 0.552,1.583 0.708,1.781 0.156,0.198 10 false 7 0.76,1.677 0.917,1.875 0.156,0.198 10 false 8 1.281,0.49 1.438,0.688 0.156,0.198 10 false 9 1.906,1.5 2.063,1.698 0.156,0.198 10 false 10 0.948,0.594 1.104,0.792 0.156,0.198 10 false 11 1.594,1.667 1.75,1.865 0.156,0.198 10 false 12 2.125,0.125 2.281,0.323 0.156,0.198 10 false 13 2.885,0.833 3.042,1.031 0.156,0.198 10 false 14 0.271,1.313 0.427,1.51 0.156,0.198 10 false 15 1.063,1.885 1.219,2.083 0.156,0.198 10 false 16

Step 1:

Uniformly tighten the 16 bolts in several steps in the order shown in the illustration.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


ii.

Mark the front side of the crankshaft bearing cap bolts with paint.


iii.

Step 2:

Tighten the bearing cap bolts 90° in the order shown in step 1.


iv.

Check that the paint mark is now at a 90° angle to the front.



l.

Check that the crankshaft turns smoothly.


m.
A388851E01
0.917,0.24 1.073,0.438 0.156,0.198 10 false 1 0.542,0.427 0.698,0.625 0.156,0.198 10 false 2 0.104,0.635 0.26,0.833 0.156,0.198 10 false 3 1.292,0.052 1.448,0.25 0.156,0.198 10 false 4 1.417,1.563 1.573,1.76 0.156,0.198 10 false 5 2.271,1.115 2.427,1.313 0.156,0.198 10 false 6 2.813,0.781 2.969,0.979 0.156,0.198 10 false 7 1.052,1.823 1.208,2.021 0.156,0.198 10 false 8

Install and uniformly tighten the 8 main bearing cap bolts together with 8 new seal washers in several steps in the sequence shown in the illustration.

Torque:
26 N*m (262 kgf*cm, 19 ft.*lbf)

Standard Bolt:
Item Length
Bolt A 45 mm (1.77 in.)
Bolt B 30 mm (1.18 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B


n.

Check that the crankshaft turns smoothly.


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.
A177653E07
1.271,2.927 1.635,2.688 1.635,2.688 1.75,2.688 false 1.438,3.323 1.802,3.083 1.802,3.083 1.917,3.083 true 0.198,4.083 0.406,2.427 0.406,2.427 0.583,2.427 true 1.792,2.615 2.01,2.813 0.219,0.198 10 false *2 0.677,2.313 0.896,2.5 0.219,0.188 10 false *1 1.979,3.01 2.177,3.198 0.198,0.188 10 false *3 1.615,3.688 1.719,3.854 0.104,0.167 10 true B 0.771,3.688 0.875,3.885 0.104,0.198 10 true A

Install the bearing to the connecting rod cap.

NOTICE:
·

Clean the contact surfaces of the bearing and connecting rod cap.


·

Do not apply engine oil to the bearing or the surface it contacts.



Text in Illustration
*1 Vernier Caliper
*2 Connecting Rod Cap
*3 Connecting Rod Bearing


b.

Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



c.
A177654E07
0.188,4.073 0.438,2.438 0.438,2.438 0.594,2.438 true 1.365,2.938 1.75,2.708 1.75,2.708 1.875,2.708 true 1.427,3.323 1.792,3.125 1.792,3.125 1.917,3.125 true 1.938,2.615 2.167,2.813 0.229,0.198 10 false *2 1.979,3.052 2.156,3.24 0.177,0.188 10 false *3 0.771,3.698 0.875,3.875 0.104,0.177 10 true A 1.615,3.698 1.719,3.885 0.104,0.188 10 true B 0.698,2.323 0.906,2.521 0.208,0.198 10 false *1

Install the bearing to the connecting rod.

NOTICE:
·

Clean the contact surface of the bearing and connecting rod.


·

Do not apply engine oil to the bearing or the surface it contacts.



Text in Illustration
*1 Vernier Caliper
*2 Connecting Rod
*3 Connecting Rod Bearing


d.

Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 9.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.


b.
A388848E01
0.448,1.813 0.76,2.01 0.313,0.198 10 false *1 0.438,0.188 0.75,0.385 0.313,0.198 10 false *2 2.26,0.031 2.573,0.229 0.313,0.198 10 false *3 2.26,1.958 2.573,2.156 0.313,0.198 10 false *4 0.24,1 0.552,1.198 0.313,0.198 10 false *5 0.323,1.365 0.635,1.563 0.313,0.198 10 false *6

Check the positions of the piston ring ends.

Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Lower Side Rail
*4 Upper Side Rail
*5 Expander
*6 Front Mark


c.
A221140E03
0.604,0.688 0.938,0.229 0.938,0.229 1.073,0.229 true 1.135,0.135 1.323,0.313 0.188,0.177 10 false *1

Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.

Text in Illustration
*1 Front Mark


d.
A221141E07
0.313,1.375 0.531,1.375 0.531,1.375 1.302,0.854 true 0.125,1.271 0.302,1.469 0.177,0.198 10 false *1

Install each connecting rod cap so that the protrusion is facing the correct direction.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Match each numbered connecting rod cap with the correct connecting rod.



e.

Apply a light coat of engine oil to the threads of the connecting rod cap bolts.


f.

Install the connecting rod cap bolts.

HINT:

The cap bolts are tightened in 2 progressive steps.


i.
U147559

Step 1:

Install and alternately tighten the bolts of each connecting rod cap in several steps.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


ii.

Mark the front side of each connecting rod cap bolt with paint.


iii.

Step 2:

Tighten the cap bolts 90°.


iv.

Check that the paint mark is now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.