Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL INJECTOR
RM1440E _51 Engine / Hybrid System _056126 1GR-FE FUEL _0273888 FUEL INJECTOR G

1GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.


Hide 23250 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injector injection.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area and avoid any sparks or flame.

·

Do not smoke.



i.
A246130E03
0.542,0.906 0.438,0.906 0.438,0.906 0.354,1.281 false 1.146,1.646 1.146,1.583 1.146,1.583 1.01,1.5 false 2.177,0.292 2.177,0.198 2.177,0.198 1.281,0.198 false 1.865,0.458 1.865,0.198 false 2.021,1.74 1.823,1.74 false 2.479,1.51 2.427,1.51 2.427,1.51 2.323,1.781 false 2.01,2.354 1.635,2.354 false 3.135,2.365 3.031,2.365 false 3.167,1.313 3.094,1.313 3.094,1.313 2.875,1.708 false 3.073,0.5 2.875,0.5 false 2.5,0.802 2.5,0.719 2.5,0.719 2.135,0.448 false 1.083,1.688 1.26,1.844 0.177,0.156 10 false *2 0.583,0.844 0.76,1 0.177,0.156 10 false *1 3.167,2.281 3.344,2.438 0.177,0.156 10 false *9 1.448,2.281 1.625,2.438 0.177,0.156 10 false *8 2.51,1.427 2.688,1.583 0.177,0.156 10 false *7 1.604,1.656 1.781,1.813 0.177,0.156 10 false *6 3.115,0.427 3.292,0.583 0.177,0.156 10 false *5 3.229,1.25 3.406,1.406 0.177,0.156 10 false *4 1.083,0.135 1.26,0.292 0.177,0.156 10 false *3 2.385,0.823 2.635,0.979 0.25,0.156 10 false *10

Assemble SST as shown in the illustration.

SST
09268-31013  (09268-41091, 09268-41120, 09268-41141, 09268-41410, 09268-41500, 90467-13001, 95333-06030, 95336-08070)

Text in Illustration
*1 Fuel Pressure Regulator
*2 SST (Union)
*3 SST (Clip)
*4 SST (Fuel Tube Connector)
*5 SST (Hose)
*6 SST (Adapter)
*7 SST (Clamp)
*8 SST (Fuel injector)
*9 Fuel Filter
*10 SST (T-Joint)


ii.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE FUEL>FUEL PRESSURE REGULATOR>REMOVAL).


iii.

Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.


iv.

Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

NOTICE:

Do not disconnect the No. 2 fuel pipe from the fuel pressure regulator.



v.
A388714E01
2.219,1.24 2.354,1.24 2.354,1.24 2.573,0.688 false 2.24,1.823 2.396,1.823 2.396,1.823 2.583,1.469 false 2.01,1.167 2.323,1.365 0.313,0.198 10 false *1 2.042,1.74 2.354,1.938 0.313,0.198 10 false *2

Connect SST to the fuel filter.

SST
09268-31013  (09268-41500)

Text in Illustration
*1 SST (Fuel Tube Connector)
*2 Fuel Filter

CAUTION:

Always read the precautions before connecting the fuel tube connector.



vi.
A223041E03
0.969,0.208 1.073,0.208 1.073,0.208 1.333,0.417 false 1.677,1.865 1.479,1.865 false 2.406,0.875 2.333,0.875 2.333,0.875 2.219,0.677 false 2.771,0.427 2.771,0.198 false 2.698,0.448 2.875,0.615 0.177,0.167 10 false *2 2.458,0.792 2.635,0.958 0.177,0.167 10 false *4 1.708,1.792 1.885,1.958 0.177,0.167 10 false *3 0.792,0.135 0.969,0.302 0.177,0.167 10 false *1

Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.

SST
09268-31013  (09268-41091, 95336-08070)

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

Text in Illustration
*1 Fuel Pressure Regulator
*2 SST (Hose)
*3 No. 2 Fuel Pipe Sub-assembly
*4 SST (Union)


vii.

Connect the fuel return hose to the fuel outlet of the pressure regulator.


viii.
A249693E05
0.521,0.875 0.719,0.875 false 0.51,1.24 0.677,1.24 false 0.417,2.802 0.417,2.698 0.417,2.698 0.698,2.531 false 1.656,2.906 1.854,2.906 false 2.792,2.583 2.792,2.5 2.792,2.5 2.573,2.24 false 2.49,0.948 2.406,0.948 2.406,0.948 2.135,1.24 false 0.323,1.167 0.51,1.333 0.188,0.167 10 false *2 2.719,2.625 2.906,2.792 0.188,0.167 10 false *6 1.479,2.823 1.667,2.99 0.188,0.167 10 false *5 0.344,2.833 0.531,3 0.188,0.167 10 false *4 2.542,0.865 2.729,1.031 0.188,0.167 10 false *3 0.323,0.802 0.51,0.969 0.188,0.167 10 false *1

Install a new O-ring to the injector.


ix.

Connect SST (adapter and hose) to the injector and hold the injector and adapter with SST (clamp).

SST
09268-31013  (09268-41141, 09268-41410, 90467-13001, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Clip)
*3 O-Ring
*4 SST (Adapter)
*5 Vinyl Tube
*6 SST (Clamp)


x.

Put the injector into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube to the injector to contain any gasoline spray.



xi.

Connect the intelligent tester to the DLC3.


xii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



xiii.

Turn the intelligent tester on.


xiv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.


xv.
A223043E04
1.865,0.917 1.865,0.385 false 0.885,1.281 1.073,1.448 0.188,0.167 10 false *a 1.781,0.948 1.969,1.115 0.188,0.167 10 false *1

Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

71 to 86 cm3 (4.3 to 5.2 cu. in.) per 15 seconds


Difference between each injector:

15 cm3 (0.9 cu. in.) or less


Text in Illustration
*1 SST (Wire)
*a Connect

NOTICE:

Always turn the voltage on and off on the battery side, not the fuel pump side.


If the result is not as specified, replace the injector assembly.



b.

Check for fuel leakage.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

Standard fuel leakage:

1 drop or less per 12 minutes


If the fuel leakage is not as specified, replace the injector assembly.