Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL AND OIL FILTER › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056130 1GR-FE LUBRICATION _0273915 OIL AND OIL FILTER A

1GR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 51457F 1.REMOVE ENGINE UNDER COVER SEAL

a.

Remove the 2 bolts and engine under cover seal.


Hide 52129B 2.DISCONNECT FRONT BUMPER COVER LOWER

a.
A225444

Remove the 2 bolts and clip and disconnect the front bumper cover lower.


Hide 51405A 3.DISCONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224795

Remove the 4 bolts and open the No. 1 engine under cover as shown in the illustration.


Hide 4.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and drain the engine oil into a container.


c.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 5.REMOVE OIL FILTER ELEMENT

a.
A388636E01
1.594,0.229 1.906,0.427 0.313,0.198 10 false *1 2.844,1.021 3.156,1.219 0.313,0.198 10 false *2

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

Text in Illustration
*1 Pipe
*2 Hose


b.
A222100

Remove the oil filter drain plug.


c.
A222101E04
1.281,2.938 1.052,2.938 false 1.115,2.74 0.604,2.74 true 0.5,2.167 0.792,2.167 0.792,2.167 1.073,2.323 true 0.594,2.458 1,2.458 1,2.458 1.344,2.583 true 0.813,1.781 0.604,1.781 0.604,1.781 0.563,1.896 false 0.844,1.708 1.021,1.875 0.177,0.167 10 false *1 0.323,2.083 0.5,2.25 0.177,0.167 10 false *2 0.417,2.385 0.594,2.552 0.177,0.167 10 false *3 0.417,2.698 0.594,2.865 0.177,0.167 10 false *4 0.885,2.875 1.063,3.042 0.177,0.167 10 false *5

Install the pipe to the oil filter cap.

Text in Illustration
*1 Cap
*2 Valve
*3 Pipe
*4 O-Ring
*5 Hose

HINT:

Use a container to catch the draining oil.


NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.



d.
A222102

Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.


e.
A222103E02
2.521,1 2.927,1 false 2.406,1.458 2.792,1.458 false 2.969,0.917 3.177,1.104 0.208,0.188 10 false *1 2.833,1.375 3.146,1.542 0.313,0.167 10 false SST

Using SST, remove the oil filter cap.

Text in Illustration
*1 Oil Filter Bracket Clip

SST
09228-06501  

NOTICE:

Do not remove the oil filter bracket clip.



f.
A153538E03
0.517,1.06 0.706,1.268 0.189,0.208 10 *1 1.029,1.146 0.735,1.146 false

Remove the oil filter element and O-ring from the oil filter cap.

Text in Illustration
*1 O-Ring

NOTICE:

Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.



Hide 6.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap, the threads and O-ring groove.


b.

Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.


c.

Set a new oil filter element on the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.


f.
A222104E03
2.521,0.969 2.917,0.969 false 1.677,1.042 1.271,1.323 1.271,1.323 1.042,1.323 true 2.417,1.448 2.813,1.448 false 2.865,1.354 3.208,1.552 0.344,0.198 10 false SST 2.948,0.896 3.125,1.073 0.177,0.177 10 false *1 0.854,1.24 1.031,1.417 0.177,0.177 10 false *a

Using SST, tighten the oil filter cap.

Text in Illustration
*1 Oil Filter Bracket Clip
*a No Clearance

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

When tightening the oil filter cap, do not remove the oil filter bracket clip.

·

Make sure that the oil filter is installed securely as shown in the illustration.

·

Make sure that the O-ring does not get caught between the parts.




g.
A222105E05
1.135,2.813 0.573,2.813 true 0.406,2.729 0.573,2.906 0.167,0.177 10 false *1

Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

Text in Illustration
*1 O-Ring

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between the parts.



Hide 7.ADD ENGINE OIL

a.

Add fresh oil.

Standard Engine Oil:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving" or ILSAC multigrade engine oil 0W-20
5W-20
5W-30
10W-30
API grade SL or SM multigrade engine oil 15W-40
20W-50


Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 Imp. qts)
Drain and refill with oil filter change 6.2 liters (6.6 US qts, 5.5 Imp. qts)
Dry fill 7.1 liters (7.5 US qts, 6.2 Imp. qts)



Hide 9.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.


Hide 51405A 10.CONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A225431

Install the 4 bolts to close the No. 1 engine under cover.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52129B 11.CONNECT FRONT BUMPER COVER LOWER

a.

Connect the front bumper cover lower with the 2 bolts and clip.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 51457F 12.INSTALL ENGINE UNDER COVER SEAL

a.

Install the engine under cover seal with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)