Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056132 CRUISE CONTROL _0273923 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit Malfunction  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.

When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.

DTC Code DTC Detection Condition Trouble Area
P0571 The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
·

Stop light switch circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

E195927E02
0.19,0.686 1.187,0.854 0.996,0.167 10 from IG2 Relay 0.396,1.471 1.188,1.638 0.792,0.167 10 from Battery 2.175,1.317 2.586,1.482 0.411,0.165 10 STOP 2.245,0.523 2.522,0.688 0.276,0.165 10 IGN 3.336,0.588 3.434,0.753 0.098,0.165 10 4 4.246,0.588 4.344,0.753 0.098,0.165 10 3 3.336,1.368 3.434,1.533 0.098,0.165 10 2 4.246,1.368 4.344,1.533 0.098,0.165 10 1 3.481,1.847 3.671,2.005 0.191,0.158 10 A4 3.481,2.01 5.213,2.168 1.732,0.158 10 Stop Light Switch Assembly 6.303,2.012 6.644,2.159 0.341,0.147 10 ECM 6.105,1.486 6.392,1.636 0.288,0.151 10 STP 6.105,0.701 6.476,0.852 0.371,0.151 10 ST1- 5.84,0.513 5.936,0.652 0.096,0.139 10 8 5.762,0.699 6.021,0.843 0.259,0.144 10 F51 5.762,1.491 6.021,1.635 0.259,0.144 10 F50 5.791,1.303 5.969,1.443 0.178,0.139 10 18

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)
a.
U181062E01
0.073,0 0.267,0.163 0.194,0.163 10 *a 1.616,0.26 1.810,0.402 0.194,0.142 10 A4

Disconnect the A4 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-2 - Body ground Always 11 to 14 V
A4-4 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
E200744E05
1.031,0.906 1.167,0.271 1.167,0.271 1.25,0.271 false 1.167,1.531 2.198,1.698 1.031,0.167 10 false *b 0.75,1.531 1.281,1.698 0.531,0.167 10 false *a 1.271,0.198 1.625,0.385 0.354,0.188 10 false *1

Remove the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed Below 8.3 Ω
Pushed 10 kΩ or higher
3 - 4 Pushed Below 1.6 Ω
Not pushed 10 kΩ or higher


Text in Illustration
*1 Pin
*a Not pushed
*b Pushed



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
a.

Disconnect the A4 switch connector.


b.

Disconnect the F50 and F51 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-3 - F51-8 (ST1-) Always Below 1 Ω
A4-1 - F50-18 (STP)
A4-3 - Body ground Always 10 kΩ or higher
A4-1 - Body ground




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR