Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1440E _52 Drivetrain _056134 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0273939 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0705 One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
·

P input signal is ON

·

N input signal is ON

·

NSW input signal is ON

·

R input signal is ON

·

D input signal is ON


(B) Any of the following signals is ON for 2.0 sec. or more with the shift lever in S (2-trip detection logic):
·

P input signal is ON

·

N input signal is ON

·

NSW input signal is ON

·

R input signal is ON


(C) All switches are OFF simultaneously for P, R, N, D and NSW (2-trip detection logic).
·

Open or short in park/neutral position switch circuit

·

Transmission control switch (transmission floor shift assembly)

·

Park/neutral position switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position (P, R, N, D or S) and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C177781E31
5.469,2.375 5.792,2.573 0.323,0.198 10 false B36 5.469,2.979 5.792,3.177 0.323,0.198 10 false B36 5.469,3.573 5.792,3.771 0.323,0.198 10 false B36 5.469,4.167 5.792,4.365 0.323,0.198 10 false B36 5.469,1.208 5.792,1.406 0.323,0.198 10 false B37 5.833,5.885 6,6.083 0.167,0.198 10 false S 5.833,4.177 6,4.375 0.167,0.198 10 false P 5.833,3.573 6,3.771 0.167,0.198 10 false R 5.833,2.969 6,3.167 0.167,0.198 10 false N 5.833,2.375 6,2.573 0.167,0.198 10 false D 3.729,2.198 3.979,2.396 0.25,0.198 10 false DL 3.729,2.792 3.979,2.99 0.25,0.198 10 false NL 3.729,3.396 3.979,3.594 0.25,0.198 10 false RL 3.729,4 3.979,4.198 0.25,0.198 10 false PL 2.99,1.75 3.24,1.948 0.25,0.198 10 false B 2.99,3.104 3.24,3.302 0.25,0.198 10 false RB 5.521,2.781 5.771,2.979 0.25,0.198 10 false 29 5.521,2.188 5.771,2.385 0.25,0.198 10 false 27 5.521,3.385 5.771,3.583 0.25,0.198 10 false 28 5.521,5.708 5.771,5.906 0.25,0.198 10 false 24 5.521,3.979 5.771,4.177 0.25,0.198 10 false 35 5.573,1.01 5.719,1.208 0.146,0.198 10 false 2 3.969,4.281 4.135,4.479 0.167,0.198 10 false 6 3.969,2.052 4.135,2.25 0.167,0.198 10 false 5 3.969,3.698 4.135,3.896 0.167,0.198 10 false 1 2.781,3.365 2.948,3.563 0.167,0.198 10 false 2 2.781,2.01 2.948,2.208 0.167,0.198 10 false 4 3.969,3.094 4.135,3.292 0.167,0.198 10 false 9 3.969,2.5 4.135,2.698 0.167,0.198 10 false 7 5.479,5.896 5.802,6.094 0.323,0.198 10 false F50 2.552,4.646 2.875,4.844 0.323,0.198 10 false B42 5.833,1.219 6.229,1.417 0.396,0.198 10 false NSW 6.135,7.052 6.51,7.25 0.375,0.198 10 false ECM 2.552,4.823 4.469,5.021 1.917,0.198 10 false Park/Neutral Position Switch 2.531,6.406 2.948,6.604 0.417,0.198 10 false F76 2.531,6.594 4.396,6.792 1.865,0.198 10 false Transmission Control Switch 2.781,5.99 2.979,6.188 0.198,0.198 10 false 3 3.969,5.99 4.198,6.188 0.229,0.198 10 false 7 2.99,5.729 3.24,5.927 0.25,0.198 10 false IG 3.792,5.729 4.042,5.927 0.25,0.198 10 false S 3.792,1.75 4.042,1.948 0.25,0.198 10 false L 4.552,1.885 5.333,2.083 0.781,0.198 10 false to ST Relay 0.323,3.24 1.958,3.438 1.635,0.198 10 false from ECU-IG NO. 1 Fuse 0.323,5.854 1.958,6.052 1.635,0.198 10 false from ECU-IG NO. 1 Fuse 0.281,1.885 2,2.083 1.719,0.198 10 false from Ignition Switch (ST1)

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
Shift SW Status (P Range) PNP switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
Shift SW Status (R Range) PNP switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
Shift SW Status (N Range) PNP switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.



PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E14
1.656,0.771 1.125,0.333 true 1.125,1.385 1.656,0.958 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.927,0.229 1.167,0.427 0.24,0.198 10 false IG 0.958,1.292 1.146,1.49 0.188,0.198 10 false S

Disconnect the F76 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

2.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

2.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
a.
U180824E02
1.802,1.073 2.344,0.76 false 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 2.385,0.656 2.698,0.854 0.313,0.198 10 false IG 0.552,1 0.927,1.229 0.375,0.229 10 false F76

Disconnect the F76 transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F76-3 (IG) - Body ground Ignition switch ON 11 to 14 V
F76-3 (IG) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY)

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E10
1.844,0.99 2.219,0.365 true 1.292,1 0.917,0.365 true 2.094,1.24 2.458,1.781 true 0.99,1.781 1.365,1.24 true 1.604,0.969 1.521,0.365 true 2.052,1.781 1.969,1.24 true 1.635,1.781 1.719,1.24 true 2.26,0.25 2.573,0.448 0.313,0.198 10 false RL 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.76,0.25 1.073,0.448 0.313,0.198 10 false B 2.5,1.677 2.813,1.875 0.313,0.198 10 false L 0.729,1.677 1.042,1.875 0.313,0.198 10 false NL 1.25,0.25 1.563,0.448 0.313,0.198 10 false RB 2.094,1.677 2.406,1.875 0.313,0.198 10 false PL 1.375,1.677 1.688,1.875 0.313,0.198 10 false DL

Disconnect the B42 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever in N Below 1 Ω
2 (RB) - 7 (DL)
·

Shift lever in D

·

Shift lever in S, "+" or "-"


Below 1 Ω
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL)
·

Shift lever not in D

·

Shift lever not in S, "+" or "-"


10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch)



OK

4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

NG

4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
U180813E02
1.792,1.021 2.167,0.333 false 0.375,1.042 0.75,1.271 0.375,0.229 10 false B42 2.208,0.229 2.521,0.427 0.313,0.198 10 false RB 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a

Disconnect the B42 park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B42-2 (RB) - Body ground Ignition switch ON 11 to 14 V
B42-2 (RB) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
U180919E02
2.719,2.646 2.094,1.896 false 2.24,2.99 1.656,2.156 false 1.667,2.656 1.594,2.167 false 1.115,2.99 1.531,2.219 false 0.646,2.646 1.531,2.156 false 0.052,0.031 0.302,0.229 0.25,0.198 10 false *a 1.458,0.427 1.833,0.656 0.375,0.229 10 false B36 1.427,2.677 1.875,2.875 0.448,0.198 10 false 28 (R) 0.844,3.021 1.292,3.219 0.448,0.198 10 false 35 (P) 0.333,2.677 0.781,2.875 0.448,0.198 10 false 29 (N) 2.563,2.677 3.135,2.875 0.573,0.198 10 false 2 (NSW) 2.021,3.021 2.469,3.219 0.448,0.198 10 false 27 (D) 1.906,0.427 2.281,0.656 0.375,0.229 10 false B37

Disconnect the B36 and B37 ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B36-35 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
B36-28 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
B36-29 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
B36-27 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
B37-2 (NSW) - Body ground
·

Ignition switch ON

·

Shift lever not in P or N


11 to 14 V
B36-35 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
B36-28 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
B36-29 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
B36-27 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V
B37-2 (NSW) - Body ground
·

Ignition switch ON

·

Shift lever in P or N


Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)

HINT:

*: The voltage will drop slightly due to the illumination of the back-up light.




OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U180906E02
0.563,2.76 0.823,2.094 false 0.052,0.031 0.302,0.229 0.25,0.198 10 false *a 0.844,0.396 1.219,0.625 0.375,0.229 10 false F50 0.292,2.802 0.75,3 0.458,0.198 10 false 24 (S)

Disconnect the F50 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F50-24 (S) - Body ground Shift lever in S, "+" or "-" 11 to 14 V
F50-24 (S) - Body ground Shift lever not in S, "+" or "-" Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR