Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION FLUID
RM1440E _52 Drivetrain _056134 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0273952 AUTOMATIC TRANSMISSION FLUID N

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

C210202E01
1.645,3.18 4.279,3.363 2.634,0.183 12 FLUID TEMPERATURE CHECK 0.406,5.189 2.210,5.383 1.803,0.194 12 FLUID LEVEL CHECK 0.173,0.06 2.255,0.400 2.083,0.340 12 Fluid Filling Procedure: 0.166,0.419 1.942,0.827 1.776,0.409 12 TRANSMISSION FILL (When necessary) 0.155,1.107 2.961,1.285 2.806,0.178 10 Add fluid to the oil pan to the specified level. 4.16,0.746 6.830,1.103 2.670,0.357 10 Add the correct amount of fluid specified for the operation that was performed. 0.239,2.234 1.635,2.876 1.395,0.642 10 Add fluid until fluid comes out of the overflow plug hole. 0.131,7.008 2.266,7.404 2.135,0.396 10 Keep the overflow plug open until only drops of fluid come out. 0.413,5.539 2.881,6.016 2.468,0.477 10 Drain excess fluid at the specified fluid temperature. 4.322,5.445 6.801,5.781 2.479,0.336 10 If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.613,3.53 7.061,3.947 5.447,0.417 10 Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified value. 6.242,1.586 6.887,2.107 0.644,0.521 10 Specified Amount of Fluid 2.03,2.445 3.348,2.823 1.318,0.378 10 No. 1 Transmission Oil Filler Tube 1.78,2.016 2.63,2.369 2.63,2.369 2.63,2.414 false 5.244,1.944 5.84,2.186 5.84,2.186 5.84,2.29 false 5.328,2.331 6.307,2.525 0.979,0.194 10 Overflow Plug 3.977,5.35 7.107,7.643 3.13,2.293

NOTICE:
·

This transmission requires Toyota Genuine ATF WS.

·

After servicing the transmission, you must follow the ATF adjustment procedure.

·

Maintain the vehicle in a horizontal position while adjusting the fluid level.



PROCEDURE

Hide 1. BEFORE FILLING TRANSMISSION

·

When you have replaced the entire transmission, transmission pan, drain plug, valve body and/or torque converter, proceed to the "Transmission Fill" procedures.

·

When you have replaced the transmission hose and/ or output shaft oil seal, proceed to the "Fluid Temperature Check" procedures.


Hide 2. TRANSMISSION FILL

C112857E10
1.031,1.531 1.24,0.688 1.24,0.688 1.354,0.688 true 0.781,1.333 1.021,0.344 1.021,0.344 1.135,0.344 true 1.5,3.708 1.354,4.302 1.354,4.302 1.24,4.302 false 1.375,0.615 1.521,0.75 0.146,0.135 10 false *1 1.177,0.271 1.323,0.406 0.146,0.135 10 false *3 1.031,4.198 1.198,4.365 0.167,0.167 10 false *2

a.

Remove the refill plug and overflow plug.

Text in Illustration
*1 Refill Plug
*2 Overflow Plug
*3 Refill Hole


b.
C361847E01
0.75,1.229 0.906,1.229 0.906,1.229 1.104,0.823 true 2.5,1.25 2.354,1.25 2.354,1.25 1.792,0.833 true 2.552,1.167 2.865,1.365 0.313,0.198 10 false *1 0.563,1.135 0.875,1.333 0.313,0.198 10 false *a

Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.

Text in Illustration
*1 Overflow Tube
*a Specified fluid level


c.

Reinstall the overflow plug.


d.

Fill the transmission with the amount of fluid listed in the table below.

Reference Capacity:
Repair Fill Amount
Transmission pan and drain plug removal 1.7 liters (1.8 US qts, 1.5 Imp. qts)
Transmission valve body removal 4.3 liters (4.5 US qts, 3.8 Imp. qts)
Torque converter removal 5.4 liters (5.7 US qts, 4.8 Imp. qts)



e.

Install the refill plug.

HINT:

If you cannot fill the listed amount of fluid, perform the following:


i.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



ii.

Move the shift lever through the entire gear range to circulate the fluid.


iii.

Wait for 30 seconds with the engine idling.


iv.

Stop the engine.


v.

Remove the refill plug.


vi.

Fill the transmission with the remaining fluid until the amount in the table has been filled.


vii.

Install the refill plug.



Hide 3. FLUID TEMPERATURE CHECK

NOTICE:

The ATF temperature can be confirmed by using the intelligent tester.


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Powertrain / ECT / Data List / A/T Oil Temperature 1.


e.

Check the ATF temperature.

NOTICE:

If the ATF temperature is higher than 45°C (113°F), turn the ignition switch off and wait until the fluid temperature drops to between 40 and 45°C (104 and 113°F).



Hide 4. FLUID LEVEL CHECK

NOTICE:
·

It is necessary to change to temperature detection mode in order to idle the vehicle appropriately.

·

The ATF temperature must be between 40 and 45°C (104 and 113°F) to accurately check the fluid level.



a.

When using the intelligent tester:

Enter the following menus: Powertrain / ECT / Active Test / Connect the TC and TE1.

Standard condition:

Indicator lights in the combination meter blink.



b.
C361850E01
1.708,0.927 1.844,0.469 1.844,0.469 1.979,0.469 true 1.625,1.875 1.781,1.875 1.781,1.875 1.896,1.479 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 2.021,0.385 2.333,0.583 0.313,0.198 10 false CG 1.385,1.792 1.698,1.99 0.313,0.198 10 false TC

When not using the intelligent tester:

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Standard condition:

Indicator lights in the combination meter blink.


Text in Illustration
*a Front view of DLC3:


c.

Start the engine and idle it.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



d.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then return the shift lever to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.



e.
C216903E01
0.074,0.007 0.376,0.197 0.302,0.191 12 * A 0.086,2.274 0.367,2.472 0.281,0.198 12 * B

Move the shift lever to D, and quickly move it back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

Standard condition:

Indicator light [D] remains illuminated for 2 seconds and then turns off.


Text in Illustration
*A Optitron Meter
*B Standard Meter


f.

When using the intelligent tester:

Return the shift lever to P and terminate the Active Test on the intelligent tester.


g.

When not using the intelligent tester:

Return the shift lever to P and disconnect SST from the DLC3.


h.

Allow the engine to idle until the fluid temperature reaches 40 to 45°C (104 to 113°F).

HINT:

The indicator [D] will come on again when the fluid temperature reaches 40°C (104°F) and will blink if it is higher than 45°C (113°F).


Indicator [D] Indication of ATF Temperature
Below 40°C (104°F) 40 to 45°C (104 to 113°F) Higher than 45°C (113°F)
Turn off Turn on Blinking


i.
C361847E01
0.75,1.229 0.906,1.229 0.906,1.229 1.104,0.823 true 2.5,1.25 2.354,1.25 2.354,1.25 1.792,0.833 true 2.552,1.167 2.865,1.365 0.313,0.198 10 false *1 0.563,1.135 0.875,1.333 0.313,0.198 10 false *a

Remove the overflow plug and gasket with the engine idling.


j.

Wait until the overflow slows to a trickle.

Text in Illustration
*1 Overflow Tube
*a Specified fluid level

NOTICE:

If the fluid does not overflow, perform the following:


i.

Remove the refill plug and gasket.


ii.

Refill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.


iii.

Wait until the overflow slows to a trickle.



k.

Install a new gasket and the overflow plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


l.

Install a new gasket and the refill plug.

Torque:
37 N*m (379 kgf*cm, 27 ft.*lbf)


Hide 5. COMPLETE

a.

Turn the ignition switch off.


b.

When using the intelligent tester:

Disconnect the intelligent tester from the DLC3.


c.

Inspect for automatic transmission fluid leak.