Home › Drivetrain › VF4BM TRANSFER / 4WD / AWD › 4WD CONTROL SWITCH
RM1440E _52 Drivetrain _056135 VF4BM TRANSFER / 4WD / AWD _0273957 4WD CONTROL SWITCH G

VF4BM TRANSFER / 4WD / AWD  4WD CONTROL SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84223A 1.INSPECT TRANSFER POSITION SWITCH

a.

Check the harness and connector (four wheel drive control ECU - battery and body ground).

i.
U150289E02
2.281,0.927 2.146,0.438 2.146,0.438 2.052,0.438 false 2.146,1 2.031,1.719 false 0.094,0.052 0.281,0.219 0.188,0.167 10 false *a 2.344,0.323 2.688,0.5 0.344,0.177 10 false F46 1.833,1.74 2.24,1.948 0.406,0.208 10 false GND 1.813,0.365 2.063,0.531 0.25,0.167 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F46-3 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(Four Wheel Drive Control ECU)

If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).

If there is a malfunction, repair or replace the harness or connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
F46-4 (GND) - Body ground Always Below 1 Ω




b.

Check the harness and connector (transfer position switch - four wheel drive control ECU).

i.

Disconnect the F47 ECU connector.


ii.

Disconnect the F73 switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U150304E02
1.698,0.875 1.427,1.354 false 2.438,0.865 2.656,1.333 false 5.323,0.75 5.063,1.375 true 5.594,0.75 5.854,1.375 true 2.042,0.875 2.042,1.365 false 4.063,0.031 4.271,0.188 0.208,0.156 10 false *b 0.667,0 0.875,0.167 0.208,0.167 10 false *a 3.479,0.698 3.813,0.896 0.333,0.198 10 false F47 0.969,0.656 1.302,0.854 0.333,0.198 10 false F73 1.385,1.354 1.563,1.51 0.177,0.156 10 false HI 1.906,1.365 2.25,1.542 0.344,0.177 10 false GND 2.573,1.354 2.802,1.542 0.229,0.188 10 false LO 4.906,1.396 5.198,1.583 0.292,0.188 10 false 2-4 5.771,1.396 6.021,1.594 0.25,0.198 10 false LO

Standard resistance:
Tester Connection Condition Specified Condition
F73-5 (LO) - F47-13 (LO) Always Below 1 Ω
F73-5 (LO) - Body ground Always 100 kΩ or higher
F73-3 (GND) - Body ground Always Below 1 Ω
F73-1 (HI) - F47-11 (2-4) Always Below 1 Ω
F73-1 (HI) - Body ground Always 100 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transfer Position Switch)
*b Front view of wire harness connector
(to Four Wheel Drive Control ECU)

If the result is not as specified, repair or replace the harness or connector.



c.

Check the transfer position switch.

i.

Turn the ignition switch off.


ii.

Connect the F73 switch connector.


iii.

Connect the F47 ECU connector.


iv.
U150290E02
1.24,1.031 1.938,1.635 false 1.083,1.021 0.406,1.635 false 0.094,0.052 0.469,0.323 0.375,0.271 10 false *a 1.146,0.313 1.51,0.49 0.365,0.177 10 false F47 1.833,1.656 2.177,1.833 0.344,0.177 10 false 2-4 0.271,1.656 0.521,1.823 0.25,0.167 10 false LO

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F47-11 (2-4) - Body ground Ignition switch ON
Transfer position switch H4F
Below 1.5 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
10.5 to 14 V
F47-13 (LO) - Body ground Ignition switch ON
Transfer position switch H4F
10.5 to 14 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
Below 1.5 V


Text in Illustration
*a Component with harness connected
(Four Wheel Drive Control ECU)

If the result is not as specified, check the four wheel drive control ECU.



d.

Check the four wheel drive control ECU.

i.

Disconnect the F73 switch connector.


ii.
U150306E01
0.117,0.063 0.305,0.238 0.189,0.175 10 *a 0.364,0.831 0.700,1.023 0.336,0.193 10 F73 2.363,1.794 2.579,1.942 0.216,0.149 10 LO 0.937,1.794 1.133,1.938 0.196,0.145 10 HI 1.379,1.194 1.041,1.756 false 2.203,1.186 2.443,1.759 false

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F73-1 (HI) - Body ground Ignition switch ON 10.5 to 14 V
F73-5 (LO) - Body ground Ignition switch ON 10.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Position Switch)

If the voltage is not as specified, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL). If the voltage is normal, replace the transfer position switch (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL SWITCH>REMOVAL).