Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM1440E _52 Drivetrain _056136 DRIVE SHAFT / PROPELLER SHAFT _0273960 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER

F041033E22
0.563,0.635 0.385,0.333 false 0.208,0.177 0.521,0.375 0.313,0.198 10 false SST

a.

Using SST and a press, install a new dust cover.

SST
09527-10011  


Hide 43412B 2.INSTALL SHAFT SNAP RING

C174231

a.

Install a new snap ring.


Hide 3.INSTALL OUTBOARD JOINT BOOT

C177228E02
2.537,1.055 2.752,1.225 0.215,0.170 10 *1 2.05,0.848 2.363,1.166 false 2.363,1.166 2.464,1.166 false

HINT:

Before installing the boot, wrap vinyl tape around the spline of the shaft to prevent damage to the boot.


Text in Illustration
*1 Vinyl Tape

a.

Temporarily install a new outboard joint boot with 2 new clamps to the outboard joint shaft.


b.

Pack the outboard joint and boot with grease from the boot kit.

Standard grease capacity:

266 to 276 g (9.4 to 9.7 oz.)



Hide 43447F 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

U116682E02
1.75,0.594 2.01,0.729 false 1.75,0.594 1.469,0.594 false 1.083,0.51 1.375,0.688 0.292,0.177 10 false SST 1.875,0.115 2.083,0.302 0.208,0.188 10 false *a 2.333,1.865 2.563,2.052 0.229,0.188 10 false *b

a.

Hold the drive shaft lightly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Place SST onto the front No. 2 axle outboard joint boot clamp.

SST
09521-24010  

Text in Illustration
*a Hold
*b Turn


c.

Tighten SST so that the No. 2 front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.
F052127E05
0.813,0.5 1.125,0.813 false 0.448,0.396 0.74,0.573 0.292,0.177 10 false SST

Using SST, measure the clearance of the No. 2 front axle out board joint boot clamp.

SST
09240-00020  

Standard clearance:

2.1 mm (0.0827 in.) or less


NOTICE:

If the measured value is more than the specified value, retighten the clamp.



Hide 43447E 5.INSTALL FRONT NO. 1 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft lightly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Secure the outboard joint boot clamp to the boot.


c.
C362040E01
1.542,1.01 0.823,0.625 0.823,0.625 0.677,0.625 true 0.354,0.542 0.813,0.74 0.458,0.198 10 false SST 0.99,0.104 1.302,0.302 0.313,0.198 10 false *a 2.5,1.583 2.813,1.781 0.313,0.198 10 false *b

Place SST onto the outboard joint boot clamp.

SST
09521-24010  

Text in Illustration
*a Hold
*b Turn


d.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.
C362041E01
1.646,1.26 2.635,1.458 true 2.677,1.375 3.135,1.573 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00020  

Standard clearance:

1.3 mm (0.0512 in.) or less


NOTICE:

If the measured value is more than the specified value, retighten the clamp.



Hide 6.INSTALL INBOARD JOINT BOOT

a.

Temporarily install a new inboard joint boot to the outboard joint shaft.


Hide 43403B 7.INSTALL FRONT AXLE INBOARD JOINT ASSEMBLY

a.

Install new parts to the outboard joint shaft in the following order.

1. Front axle inboard joint boot clamp
2. Front axle inboard joint boot
3. Front No. 2 axle inboard joint boot clamp


b.

Secure the outboard joint shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C067417E41
1.271,1.729 2.406,1.677 2.406,1.677 1.781,1.438 false 1.031,0.771 1.792,0.302 false 2.427,1.615 2.667,1.813 0.24,0.198 10 false *b 1.802,0.188 2.063,0.385 0.26,0.198 10 false *a

Align the matchmarks and install the tripod joint to the outboard joint shaft.

NOTICE:

Position tripod so that the beveled side of the tripod faces toward the inboard joint.


Text in Illustration
*a Beveled
*b Matchmark


d.

Align the matchmarks and install the tripod to the inboard joint.


e.

Using a brass bar and hammer, tap the tripod onto the drive shaft.

NOTICE:
·

Do not hit the roller portion.

·

Keep the tripod joint free of foreign matter.




f.
G022501

Using a snap ring expander, install a new snap ring.


g.

Pack the inboard joint assembly and boot with grease from the boot kit.

Standard grease capacity:

239 to 249 g (8.4 to 8.7 oz.)



h.
C362042E01
1.396,1.24 0.906,0.542 0.906,0.542 1.792,0.771 false 0.688,0.427 1,0.625 0.313,0.198 10 false *a

Align the matchmarks and install the inboard joint onto the outboard joint shaft.

Text in Illustration
*a Matchmark


Hide 43448F 8.INSTALL FRONT NO. 1 AXLE INBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft lightly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Secure the inboard joint boot clamp to the boot.


c.
U116380E02
1.417,0.823 1,0.646 false 1,0.646 0.833,0.646 false 0.479,0.573 0.885,0.75 0.406,0.177 10 false SST 1.24,0.01 1.458,0.188 0.219,0.177 10 false *a 2.656,0.552 2.875,0.729 0.219,0.177 10 false *b

Place SST onto the inboard joint boot clamp.

SST
09521-24010  

Text in Illustration
*a Hold
*b Turn


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.
D026926E08
1.5,1.125 2.354,1.427 false 2.396,1.385 3.427,2.177 1.031,0.792 10 true SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00020  

Standard clearance:

1.3 mm (0.0512 in.) or less


NOTICE:

If the measured value is greater than the specified value, retighten the clamp.



Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Hold the inboard joint shaft assembly in a vise between aluminium plates.

NOTICE:

Do not overtighten the vise.



b.
U115752E03
2.135,1.115 1.823,1.438 1.823,1.438 1.167,1.438 true 1.604,0.292 1.958,0.677 0.354,0.385 10 true *a 0.865,1.375 1.219,1.552 0.354,0.177 10 false SST 2.031,1.76 2.365,1.979 0.333,0.219 10 true *b

Place SST onto the No. 2 front axle inboard joint boot clamp.

SST
09521-24010  

Text in Illustration
*a Hold
*b Turn


c.

Tighten SST so that the No. 2 front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.
C086270E11
1.906,0.802 2.052,0.802 2.052,0.802 2.052,1.521 false 1.958,1.552 2.365,1.75 0.406,0.198 10 false SST

Using SST, measure the clearance of the No. 2 front axle inboard joint boot clamp.

SST
09240-00020  

Standard clearance:

2.1 mm (0.0827 in.) or less


NOTICE:

If the measured value is greater than the specified value, retighten the clamp.