Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 2WD)
RM1440E _52 Drivetrain _056136 DRIVE SHAFT / PROPELLER SHAFT _0273963 PROPELLER SHAFT ASSEMBLY(for 2WD) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 2WD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same procedure for all rear propeller shaft universal joint spider bearing.


a.
C060598

Apply MP grease No. 2 to a new spider and bearings.

NOTICE:

Be careful not to apply too much grease.



b.

Install the spider to the propeller shaft.


c.
C362044E02
1.052,0.854 1.052,0.156 1.052,0.156 1.177,0.156 false 1.208,0.063 1.667,0.26 0.458,0.198 10 false SST

Using SST, install 2 of the bearings to the spider.

SST
09332-25010  


d.

Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal width.

SST
09332-25010  


e.
G020755

Install 4 new snap rings of equal thickness which will allow no axial play.

HINT:

Do not reuse the snap rings.


Thickness of snap ring (Both ends thin type):
Parts No. Specified Condition Mark
90520-25039 2.28 to 2.30 mm
(0.0898 to 0.0906 in.)
1
90520-25040 2.30 to 2.32 mm
(0.0906 to 0.0913 in.)
2
90520-25041 2.32 to 2.34 mm
(0.0913 to 0.0921 in.)
-
90520-25042 2.34 to 2.36 mm
(0.0921 to 0.0929 in.)
Brown
90520-25043 2.36 to 2.38 mm
(0.0929 to 0.0937 in.)
Blue
90520-25044 2.38 to 2.40 mm
(0.0937 to 0.0945 in.)
6
90520-25045 2.40 to 2.42 mm
(0.0945 to 0.0953 in.)
7
90520-25046 2.42 to 2.44 mm
(0.0953 to 0.0961 in.)
8
90520-25047 2.44 to 2.46 mm
(0.0961 to 0.0969 in.)
C335991

90520-25048 2.46 to 2.48 mm
(0.0969 to 0.0976 in.)
10
90520-25049 2.48 to 2.50 mm
(0.0976 to 0.0984 in.)
A
90520-25050 2.50 to 2.52 mm
(0.0984 to 0.0992 in.)
B
90520-25051 2.52 to 2.54 mm
(0.0992 to 0.1000 in.)
C
90520-25052 2.54 to 2.56 mm
(0.1000 to 0.1008 in.)
D
90520-25053 2.56 to 2.58 mm
(0.1008 to 0.1016 in.)
E
90520-25054 2.18 to 2.20 mm
(0.0858 to 0.0866 in.)
J
90520-25055 2.20 to 2.22 mm
(0.0866 to 0.0874 in.)
K
90520-25056 2.22 to 2.24 mm
(0.0874 to 0.0882 in.)
F
90520-25057 2.24 to 2.26 mm
(0.0882 to 0.0890 in.)
G
90520-25058 2.26 to 2.28 mm
(0.0890 to 0.0898 in.)
H


NOTICE:
·

Use a new retainer ring.

·

Use retainer rings with as close to the same thickness as possible on both ends.




f.

Using a hammer, tap the yoke until there is no clearance between the spider bearing outer race and snap ring.

HINT:

Install a new spider bearing on the sleeve side using the procedure described above.



Hide 37110 2.INSPECT PROPELLER SHAFT ASSEMBLY

HINT:

When replacing the spider bearing, be sure that the grease fitting assembly hole is facing to the direction shown in the illustration.


C218425E01
0.126,0 0.410,0.218 0.284,0.218 10 *a 2.313,0.356 2.571,0.556 0.258,0.200 10 *b

Text in Illustration
*a Spider grease fitting assembly direction for front propeller shaft assembly *b Rear Side

Hide 3.INSPECT REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING