Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT
RM1440E _52 Drivetrain _056137 AXLE AND DIFFERENTIAL _0273971 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.REMOVE PARKING BRAKE ASSEMBLY

a.

Remove the parking brake assembly (See page Brake>PARKING BRAKE>PARKING BRAKE ASSEMBLY>DISASSEMBLY).


Hide 42312E 3.REMOVE REAR AXLE HUB BOLT LH

a.
U116685E07
2.135,0.615 2.396,0.333 false 1.615,1.219 1.177,0.219 true 1.177,0.219 1.042,0.219 false 1.771,1.563 2.146,1.802 false 2.146,1.802 2.344,1.802 false 2.396,0.333 2.552,0.333 false 2.625,0.25 3.01,0.521 0.385,0.271 10 false SST 1.833,1.906 2.083,2.063 0.25,0.156 10 false *b 2.646,1.042 2.917,1.271 0.271,0.229 10 false *a 0.833,0.146 1.063,0.323 0.229,0.177 10 false *1 2.427,1.708 2.708,1.927 0.281,0.219 10 false *1

Using SST and a screwdriver or equivalent to hold the axle hub, remove the hub bolt.

SST
09650-17011  

Text in Illustration
*1 Nut
*a Turn
*b Hold

NOTICE:
·

Do not deform the oil deflector.

·

Make sure to align the notch of SST with the flange of the oil deflector.




Hide 42312E 4.INSTALL REAR AXLE HUB BOLT LH

U116686E06
2.729,0.385 2.875,0.219 false 2.875,0.219 2.99,0.219 false 3.094,1.042 3.094,1.198 false 1.031,1.333 0.385,1.865 false 0.385,1.865 0.292,1.865 false 1.198,1.698 1.427,1.917 false 1.427,1.917 1.542,1.917 false 3.031,0.146 3.302,0.354 0.271,0.208 10 false *1 3.031,1.219 3.302,1.427 0.271,0.208 10 false *2 1.708,0.333 2.063,0.521 0.354,0.188 10 false *a 0.677,1.896 0.927,2.104 0.25,0.208 10 true *b 0.094,1.792 0.281,2.021 0.188,0.229 10 false *2 1.604,1.823 1.792,2.052 0.188,0.229 10 false *2

a.

Insert a new hub bolt.


b.

Temporarily install a washer and hub nut to the hub bolt as shown in the illustration.

Text in Illustration
*1 Washer
*2 Nut
*a Turn
*b Hold

NOTICE:

Install a hub nut to prevent damage to the hub bolt.



c.

Using a screwdriver or equivalent to hold the hub, turn the hub nut until the bottom surface of the hub bolt head touches the axle hub.


d.

Remove the hub nut and washer.

NOTICE:

Do not damage the threads of the hub bolt.



Hide 5.INSTALL PARKING BRAKE ASSEMBLY

a.

Install the parking brake assembly (See page Brake>PARKING BRAKE>PARKING BRAKE ASSEMBLY>REASSEMBLY).


Hide 6.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)