Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM1440E _52 Drivetrain _056137 AXLE AND DIFFERENTIAL _0273979 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 41110 1.FIX REAR DIFFERENTIAL CARRIER ASSEMBLY IN PLACE

C216539

Hide 41204 2.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F001237E51
0.115,0.146 0.385,0.396 0.271,0.25 10 false *a 2.073,0.125 2.344,0.354 0.271,0.229 10 false *b 1.927,1.917 2.406,2.104 0.479,0.188 10 true 30 mm

a.

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Distance from center to runout measurement point:

30 mm (1.18 in.)


Maximum Runout:
Item Specified Condition
Vertical runout 0.14 mm (0.00551 in.)
Lateral runout 0.14 mm (0.00551 in.)


Text in Illustration
*a Vertical Runout
*b Lateral Runout

If the runout is more than the maximum, replace the companion flange.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

C216538

a.

Using a dial indicator, check the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

C216537

a.

Using a dial indicator, check the backlash of the ring gear.

Standard backlash:

0.10 to 0.18 mm (0.00394 to 0.00709 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 5.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

C003092

a.

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard preload (at starting):

0.88 to 1.98 N*m (9.0 to 20.2 kgf*cm, 7.8 to 17.5 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 6.INSPECT TOTAL PRELOAD

C003092

a.

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.


b.

Using a torque wrench, measure the total preload.

Standard total preload (at starting):

Drive pinion preload plus 1.08 to 2.38 N*m (11.0 to 24.3 kgf*cm, 9.6 to 21.0 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41204B 7.REMOVE REAR DRIVE PINION NUT

C361807E01
1.75,1.083 2.281,1.083 false 2.354,1 2.813,1.198 0.458,0.198 10 false SST

a.

Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

SST
09930-00010  


b.
SA02349E24
2.875,0.51 2.271,0.51 false 2.938,0.427 3.302,0.625 0.365,0.198 10 false SST

Use SST to hold the companion flange.

SST
09330-00021  


c.

Using a 30 mm socket wrench, remove the rear drive pinion nut.


Hide 41204 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

B087869E07
1.958,0.594 2.24,0.396 false 2.24,0.396 2.333,0.396 false 2.375,0.323 2.667,0.479 0.292,0.156 10 false SST

a.

Using SST, remove the rear drive pinion companion flange sub-assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41201C 9.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

C361765E02
1.344,0.844 1.156,0.635 false 0.844,0.542 1.229,0.74 0.385,0.198 10 false SST

a.

Using SST, remove the rear differential carrier oil seal from the differential carrier.

SST
09308-10010  


Hide 41214 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

Z000641E17
1.667,0.771 1.302,0.542 false 1.302,0.542 0.969,0.542 false 0.625,0.469 1.021,0.688 0.396,0.219 10 false SST

a.

Using SST, remove the rear drive pinion front tapered roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 41201B 12.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

Hide 13.REMOVE DIFFERENTIAL CASE ASSEMBLY

C216540E02
2.065,2.589 1.529,3.125 1.529,3.125 2.063,2.697 false 1.425,3.136 1.577,3.283 0.151,0.147 10 *1

a.

Place matchmarks on the bearing cap and differential carrier.

Text in Illustration
*a Matchmark


b.

Remove the 4 bolts and 2 differential bearing caps.


c.
C216541

Using a screwdriver and hammer, remove the 2 plate washers.

HINT:

Measure the plate washer thickness and note it down.



d.
C216542

Remove the rear differential case assembly from the differential carrier.

HINT:

Tag the 2 case bearing outer races so that they can be reinstalled in the correct locations.



Hide 14.REMOVE DIFFERENTIAL DRIVE PINION

a.
C030540

Remove the drive pinion and bearing spacer from the differential carrier.


Hide 41201A 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C361809E01
2.281,1.052 2.76,0.573 false 2.646,0.375 3.104,0.573 0.458,0.198 10 false SST

a.

Using SST and a press, press out the roller bearing (inner) from the drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the drive pinion.


HINT:

If the drive pinion or ring gear is damaged, replace them as a set.



Hide 41201B 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C361810E01
1.021,0.271 1.385,0.271 false 1.448,0.198 1.906,0.396 0.458,0.198 10 false SST

a.

Using SST, remove the roller bearing (outer) from the carrier.

SST
09308-00010  


b.

Using a brass bar and hammer, tap out the oil storage ring from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 41201A 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C216543E08
0.458,0.792 1.188,1.302 false 0.083,0.688 0.427,0.927 0.344,0.24 10 true SST

a.

Using SST, tap out the rear tapered roller bearing (outer) from the carrier.

SST
09308-00010  

HINT:

If the bearing is damaged during removal, replace it.



Hide 41201D 18.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 19.REMOVE DIFFERENTIAL RING GEAR

C216547E17
1.635,1.927 1.458,2.021 1.458,2.021 1.635,1.802 true 1.25,1.969 1.427,2.135 0.177,0.167 10 true *a

a.

Place matchmarks on the ring gear and differential case.

Text in Illustration
*a Matchmark


b.

Remove the 12 ring gear set bolts.


c.
C014054

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 20.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

C216544

a.

Install the rear differential case bearing to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


d.

Using a dial indicator, measure the differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



e.

Remove the differential case.


f.

Remove the rear differential case bearing.


Hide 41301A 21.REMOVE REAR DIFFERENTIAL CASE BEARING

F040345E17
0.427,0.25 0.844,0.25 false 0.844,0.25 0.844,0.781 false 0.063,0.167 0.406,0.396 0.344,0.229 10 false SST

a.

Using SST, remove the 2 bearings from the differential case.

SST
09950-40011  (09953-04020, 09951-04010, 09952-04010, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00500, 09951-00650, 09952-06010)

NOTICE:

Do not remove a case bearing unless replacing the differential case.



Hide 22.DISASSEMBLE DIFFERENTIAL CASE

C216546E10
0.604,1.594 0.875,1.76 0.875,1.76 0.615,1.854 false 0.917,1.698 1.115,1.875 0.198,0.177 10 true *1

a.

Place matchmarks on the LH and RH cases.

Text in Illustration
*a Matchmark


b.

Remove the 8 bolts.

NOTICE:

Loosen the bolts, diagonally opposite of each other, in pairs.



c.
ZK09094

Using a plastic-faced hammer, separate the LH and RH cases.


d.
C361811E01
1.219,0.208 1.375,0.208 false 1.875,0.563 2.021,0.49 false 1.125,0.458 1.448,0.948 false 1.01,0.917 0.854,1.125 0.854,1.125 1.021,1.292 false 0.823,0.823 0.417,1.146 0.417,1.146 0.844,1.438 false 2.281,0.823 2.51,1.031 2.51,1.031 2.344,1.24 false 2.469,0.656 2.958,0.969 2.958,0.969 2.552,1.417 false 1.885,1.635 2.031,1.635 false 1.25,1.958 1.396,1.958 false 1.052,0.125 1.365,0.323 0.313,0.198 10 false *2 0.948,0.365 1.26,0.563 0.313,0.198 10 false *3 2.031,0.365 2.344,0.563 0.313,0.198 10 false *1 2.542,0.938 2.854,1.135 0.313,0.198 10 false *4 3.01,0.896 3.323,1.094 0.313,0.198 10 false *5 0.219,1.063 0.531,1.26 0.313,0.198 10 false *5 0.677,1.042 0.99,1.24 0.313,0.198 10 false *4 2.073,1.563 2.385,1.76 0.313,0.198 10 false *1 1.073,1.875 1.385,2.073 0.313,0.198 10 false *2

Remove the parts shown in the illustration from the differential case.

Text in Illustration
*1 Side Gear
*2 Side Gear Thrust Washer
*3 Spider
*4 Pinion Gear
*5 Pinion Gear Thrust Washer