Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL
RM1440E _54 Brake _056143 BRAKE SYSTEM (OTHER) _0274007 BRAKE PEDAL N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 1.CHECK BRAKE PEDAL HEIGHT

a.
C253410E03
2.365,1.688 2.365,1.427 2.365,1.427 2.635,1.427 false 1.333,2.51 1.688,2.51 1.688,2.51 1.688,2.281 true 1.844,3.615 1.552,3.615 false 2.667,1.333 2.885,1.521 0.219,0.188 10 false *1 1.135,2.427 1.438,2.667 0.302,0.24 10 false *2 1.365,3.542 1.594,3.75 0.229,0.208 10 false *3 3.083,3.563 3.302,3.781 0.219,0.219 10 false *a

Check the brake pedal height.

Standard Pedal Height from Floor panel:

158.8 to 168.8 mm (6.25 to 6.46 in.)


Text in Illustration
*1 Rod Operating Adapter
*2 Stop Light Switch Assembly
*3 Floor Panel
*a Pedal Height

HINT:

Insert a ruler into the slit to measure the brake pedal height.


NOTICE:

Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.


If the pedal height is incorrect, adjust the rod operating adapter length.


b.
C253411E02
2.802,1.781 2.802,2.229 2.802,2.229 3.031,2.229 true 2.146,0.667 2.354,0.896 0.208,0.229 10 false A 3.073,2.146 3.292,2.385 0.219,0.24 10 false *1

Adjust the rod operating adapter length.

i.

Remove the clip and clevis pin.


ii.

Loosen the clevis lock nut.

Text in Illustration
*1 Clevis Lock Nut


iii.

Adjust the rod operating adapter length by turning the pedal push rod clevis.

Standard Rod Operating Adapter Length "A":

236.3 to 237.3 mm (9.30 to 9.34 in.)



iv.

Tighten the clevis lock nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the clip and clevis pin.

If the pedal height is incorrect even if the rod operating adapter is adjusted, check that there is no damage to the brake pedal, brake pedal lever, brake pedal bracket or floor panel.

·

Even if there is damage, there is no problem if the reserve distance is within the standard value.

·

If necessary, replace the clip.




Hide 84340 2.CHECK AND ADJUST STOP LIGHT SWITCH ASSEMBLY

HINT:

If the pedal height is incorrect, check and adjust the stop light switch clearance.


a.

Disconnect the stop light switch assembly connector from the stop light switch assembly.


b.

Turn the stop light switch assembly counterclockwise and remove the stop light switch assembly.


c.
C172890E23
1.635,0.698 1.635,0.156 1.635,0.156 1.74,0.156 false 0.49,1.781 1.385,1.969 0.896,0.188 10 false 1.5 to 2.5 mm 1.813,0.083 2.042,0.313 0.229,0.229 10 false *1

Insert the stop light switch assembly until the body hits the brake pedal bracket.

Text in Illustration
*1 Stop Light Switch

NOTICE:

When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.



d.

Make a quarter turn clockwise to install the stop light switch assembly.

HINT:

Due to the inverse screw structure, if the stop light switch assembly is turned clockwise, the stop light switch assembly moves in the direction to be pulled out.


NOTICE:

The turning torque for installing the stop light switch should be 1.5 N*m (15 kgf*cm, 13 in.*lbf) or less.



e.

Connect the stop light switch connector to the stop light switch assembly.


f.

Check the protrusion of the rod.

Standard Rod Protrusion:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)



g.

Install the clevis pin and clip.


h.

After adjusting the pedal height, check the pedal free play.


Hide 3.CHECK PEDAL FREE PLAY

a.
C253412E01
2.935,3.419 3.121,3.580 0.186,0.161 10 *a

Push in the pedal until the resistance is felt. Measure the distance.

Standard Pedal Free Play:

1 to 6 mm (0.0394 to 0.236 in.)


Text in Illustration
*a Pedal Free Play

HINT:

Check the brake pedal free play at the same location as that used when checking the brake pedal height.



Hide 4.CHECK PEDAL RESERVE DISTANCE

a.
R000934E41
1.75,1.729 2,2.042 0.25,0.313 10 false *a

Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance.

Pedal reserve distance from floor panel at 490 N (50 kgf, 110.2 lbf):

More than 92 mm (3.62 in.)

Text in Illustration
*a Pedal Reserve Distance


If incorrect, troubleshoot the brake system.

HINT:

Insert a ruler into the slit to measure the pedal reserve distance.