Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER
RM1440E _54 Brake _056143 BRAKE SYSTEM (OTHER) _0274008 HYDRAULIC BRAKE BOOSTER A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL BRAKE BOOSTER PISTON SUB-ASSEMBLY

a.
F051194

Apply a light coat of lithium soap base glycol grease to a new piston.


b.

Install the piston.

NOTICE:

When installing, be careful not to damage the seals, etc.



c.

Install the piston.


d.

Using 2 screwdrivers, install a new C-ring while pressing in the piston.

HINT:

Tape the screwdriver tip before use.



Hide 47265 2.INSTALL MASTER CYLINDER BOOT

Hide 47264 3.INSTALL MASTER CYLINDER PUSH ROD CLEVIS

a.

Install the brake master cylinder side lock nut and rod operating adapter to the brake master cylinder.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


b.

Install the lock nut and master cylinder push rod clevis to the rod operating adapter.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 47217 4.INSTALL MASTER CYLINDER SOLENOID

a.

Install a new gasket.

NOTICE:

Keep all surfaces of the master cylinder solenoid, master cylinder and gasket, especially contact surfaces, away from water and dust.



b.

Install the master cylinder solenoid with 6 new bolts.

Torque:
32 N*m (325 kgf*cm, 24 ft.*lbf)


Hide 47955A 5.INSTALL BRAKE BOOSTER ACCUMULATOR PIPE

a.

Install the brake booster accumulator pipe and compression spring.

NOTICE:

Make sure that no foreign matter enters the pump.



b.

Install a new O-ring to the brake booster accumulator assembly.


c.

Install the brake booster accumulator assembly.

Torque:
57 N*m (585 kgf*cm, 42 ft.*lbf)


Hide 6.INSTALL NO. 3 BRAKE ACTUATOR BRACKET

a.

Install the No. 3 brake actuator bracket.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 47967A 7.INSTALL NO. 1 BRAKE BOOSTER PUMP BRACKET

a.

Install the brake booster pump bush to the No. 1 brake booster pump bracket.


b.

Using a 5 mm hexagon wrench, install the No. 1 brake booster pump bracket with the 2 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 47070B 8.INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

a.

Using a 4 mm hexagon wrench, install the 2 pins to the brake master cylinder.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Install 2 new brake booster pump collars and 2 brake booster pump bushes to the brake booster with accumulator pump assembly.


c.

Install the brake booster with accumulator pump assembly to the brake master cylinder.


d.
U149527

Install a new clip.


e.
U116677E06
1.521,1.521 1.385,1.646 1.385,1.646 1.094,1.646 false 1.656,1.479 2.052,1.24 2.052,1.24 2.292,1.24 false 2.354,1.167 2.521,1.323 0.167,0.156 10 false *1 0.896,1.552 1.083,1.708 0.188,0.156 10 false *2

Connect the wire harnesses with the 2 screws.

Torque:
2.9 N*m (30 kgf*cm, 26 in.*lbf)

Text in Illustration
*1 Red Cable
*2 Black Cable


f.

Install 2 new plugs.


Hide 44551C 9.INSTALL NO. 1 BRAKE ACTUATOR TUBE

a.

Using a union nut wrench, install the No. 1 brake actuator tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 44571A 10.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.

Using needle nose pliers, install the brake actuator hose with the 2 clips.


Hide 47255 11.INSTALL MASTER CYLINDER RESERVOIR GROMMET

a.
F051416

Apply a light coat of lithium soap base glycol grease to 3 new reservoir grommets.


b.

Install the 3 reservoir grommets to the brake master cylinder.

NOTICE:

Be careful of the size of each grommet.



Hide 47202 12.INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.

Install the brake master cylinder reservoir sub-assembly with the screw.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


b.

Install the master cylinder reservoir filler cap.


c.

Using a pin punch and hammer, install a new pin to the brake master cylinder reservoir.


Hide 44591A 13.INSTALL NO. 1 BRAKE ACTUATOR BRACKET

a.

Install the brake fluid level warning switch connector to the No. 1 brake actuator bracket.


b.

Using a 5 mm hexagon wrench, install the No. 1 brake actuator bracket with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)