Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP
RM1440E _55 Steering _056147 POWER ASSIST SYSTEMS _0274020 VANE PUMP G

POWER ASSIST SYSTEMS  VANE PUMP  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVE BELT

a.

Visually check the belt for excessive wear, frayed cords, etc.

If any defect is found, replace the drive belt.

HINT:

Cracks on the rib side of a belt are considered acceptable. Replace the belt if there are any missing ribs.



Hide 2.BLEED AIR FROM POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.

i.

Run the engine at idle for a few minutes.



f.

Turn the steering wheel.

i.

With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1


ii.

Repeat *1 several times.



g.

Stop the engine.


h.
C124274E03
0.574,0.312 1.303,0.462 0.730,0.150 10 *a 1.919,0.312 2.841,0.462 0.922,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a CORRECT
*b INCORRECT

If the system has to be bled twice specifically because of foaming or emulsification, check for fluid leaks in the power steering system.


i.

Check the fluid level.


Hide 3.CHECK POWER STEERING FLUID LEVEL

a.
C215334

Keep the vehicle horizontal.


b.

With the engine stopped, check the fluid level in the reservoir.

If necessary, add fluid.

Fluid:

ATF "DEXRON" II or III, or equivalent


HINT:

If the fluid is hot (over 40°C (104°F)), make sure that the fluid level is within the HOT range on the reservoir. If the fluid is cold, make sure that it is within the COLD range.



c.

Start the engine and run it at idle.


d.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



e.
C124274E03
0.574,0.312 1.303,0.462 0.730,0.150 10 *a 1.919,0.312 2.841,0.462 0.922,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a CORRECT
*b INCORRECT

If foaming or emulsification is identified, bleed air from the power steering system.


f.
C106308E10
0.156,0.052 0.354,0.229 0.198,0.177 10 false *a 2.104,0.063 2.302,0.26 0.198,0.198 10 false *b 1.677,1.302 1.896,1.5 0.219,0.198 10 false *c

With the engine idling, measure the fluid level in the reservoir.

Text in Illustration
*a Engine Idling
*b Engine Stopped
*c 5 mm or less


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the reservoir.

Maximum fluid level rise:

5.0 mm (0.197 in.)


If the fluid level rise is more than the maximum, bleed air from the power steering system.


i.

Check the fluid level.


Hide 4.CHECK STEERING FLUID PRESSURE

a.

Disconnect the pressure feed tube from the vane pump.


b.
U148496E05
2.604,0.667 2.479,0.24 2.479,0.24 2.313,0.24 false 2.396,1.469 2.625,1.656 0.229,0.188 10 false *a 3.188,1.469 3.396,1.656 0.208,0.188 10 false *b 2.01,0.146 2.354,0.354 0.344,0.208 10 false SST 0.417,2.875 0.646,3.063 0.229,0.188 10 false *2 0.365,0.146 0.594,0.333 0.229,0.188 10 false *1 0.771,2.594 1,2.781 0.229,0.188 10 false *1

Connect SST as shown in the illustration below.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

Text in Illustration
*a In
*b Out
*1 Attachment
*2 Pressure Feed Tube

NOTICE:

Check that the valve of SST is in the open position.



c.

Bleed air from the power steering system.


d.

Start the engine and run it at idle.


e.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



f.
C162692E04
1.844,2.729 1.698,2.729 1.698,2.729 1.583,3.094 false 2.167,0.396 3.167,0.781 1,0.385 10 false *2 2.177,3.146 3.167,3.677 0.99,0.531 10 false *3 0.104,1.771 1.104,2.146 1,0.375 10 false *1 0.802,3.979 1.635,4.135 0.833,0.156 10 false *a 1.896,2.646 2.219,2.813 0.323,0.167 10 false SST

With the engine idling, close the valve of SST and observe the reading on SST.

Standard fluid pressure:

8300 to 8800 kPa (84.7 to 89.7 kgf/cm2, 1204 to 1276 psi)


Text in Illustration
*1 Power Steering Gear
*2 Power Steering Fluid Reservoir
*3 Power Steering Vane Pump
*a Valve Closed

NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is not within the specified range, check for fluid leaks and replace parts as necessary.


g.
C162693E05
1.823,2.719 1.688,2.719 1.688,2.719 1.542,3.104 false 2.167,0.417 3.146,0.76 0.979,0.344 10 false *2 2.177,3.146 3.156,3.667 0.979,0.521 10 false *3 0.115,1.656 1.115,2.01 1,0.354 10 false *1 0.708,3.99 1.479,4.146 0.771,0.156 10 false *a 1.875,2.625 2.198,2.792 0.323,0.167 10 false SST

With the engine idling, open the valve fully.

Text in Illustration
*1 Power Steering Gear
*2 Power Steering Fluid Reservoir
*3 Power Steering Vane Pump
*a Valve Open


h.

Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

Fluid pressure difference :

490 kPa (5.0 kgf/cm2, 71 psi) or less


NOTICE:

Do not turn the steering wheel.


If the pressure difference is above the specified range, check for fluid leaks and replace parts as necessary.


i.
C162694E02
2.152,0.385 3.141,0.744 0.989,0.358 10 *2 2.173,3.135 3.142,3.645 0.969,0.511 10 *3 0.111,1.664 1.140,2.173 1.029,0.509 10 *1 0.702,4.007 1.538,4.162 0.836,0.156 10 *a 1.871,2.638 2.193,2.808 0.323,0.170 10 SST 1.819,2.73 1.681,2.73 1.681,2.73 1.515,3.089 false

With the engine idling and the valve fully open, turn the steering wheel left or right to the full lock position. Observe the reading on SST.

Standard fluid pressure:

8300 to 8800 kPa (84.7 to 89.7 kgf/cm2, 1204 to 1276 psi)


Text in Illustration
*1 Power Steering Gear (Lock Position)
*2 Power Steering Fluid Reservoir
*3 Power Steering Vane Pump
*a Valve Open

NOTICE:
·

Do not keep the steering wheel in the full lock position for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is not within the specified range, check for fluid leaks and replace parts as necessary.


j.

Disconnect SST.


k.

Connect the pressure feed tube to the vane pump.


l.

Bleed air from the power steering system.