Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM1440E _55 Steering _056149 STEERING GEAR / LINKAGE _0274025 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REASSEMBLY  


PROCEDURE

Hide 45503 1.INSTALL STEERING RACK END SUB-ASSEMBLY

a.

Temporarily install the 2 steering rack ends to the steering rack.


b.

Fill up the ball joints of the steering rack ends with MP grease.


c.
C215762E01
1.094,1.021 1.292,0.49 1.292,0.49 1.552,0.49 false 1.375,1 1.448,0.49 false 1.615,3.135 1.74,2.802 1.74,2.802 1.865,2.802 false 0.229,0.156 0.604,0.385 0.375,0.229 12 false *A 0.208,2.813 0.583,3.042 0.375,0.229 12 false *B 0.458,1.708 0.833,1.938 0.375,0.229 10 false *a 3.031,1.021 3.25,1.25 0.219,0.229 10 false *b 0.708,4.292 1.083,4.521 0.375,0.229 10 false *b 1.594,0.417 2.25,0.719 0.656,0.302 10 false SST 1.917,2.729 2.573,3.031 0.656,0.302 10 false SST

Using SST, install the steering rack end (RH side) to the steering rack.

SST
09922-10010  

Torque:
without SST : 105 N*m (1071 kgf*cm, 77 ft.*lbf)
with SST : 77 N*m (784 kgf*cm, 57 ft.*lbf)

Text in Illustration
*A LH Side
*B RH Side
*a Hold
*b Turn

HINT:
·

Rotate SST in the direction shown in the illustration.

·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.).




d.

Using SST and a wrench, install the steering rack end (LH side) to the steering rack.

SST
09922-10010  

Torque:
without SST : 105 N*m (1071 kgf*cm, 77 ft.*lbf)
with SST : 77 N*m (784 kgf*cm, 57 ft.*lbf)

HINT:
·

Rotate SST in the direction shown in the illustration.

·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.).




Hide 45536 2.INSTALL NO. 2 STEERING RACK BOOT

a.

Apply silicon grease to the inside of the small opening of the boot.


b.

Install the 2 boots to the groove on the rack housing.


Hide 45535 3.INSTALL NO. 1 STEERING RACK BOOT

HINT:

Use the same procedures described for the No. 2 boot.


Hide 4.INSTALL STEERING RACK BOOT CLAMP RH

a.
C124255E03
0.106,1.754 0.408,1.904 0.301,0.15 10 SST 0.691,1.601 0.549,1.837 0.549,1.837 0.469,1.837 false

Using SST, install a new boot clamp as shown in the illustration.

SST
09521-24010  

Standard clearance:

3.0 mm (0.118 in.) or less


NOTICE:

Be careful not to damage the boot.



Hide 5.INSTALL STEERING RACK BOOT CLAMP LH

HINT:

Use the same procedures described for the RH side.


Hide 6.INSTALL STEERING RACK BOOT CLIP RH

a.
C361757E01
2.042,0.344 2.354,0.542 0.313,0.198 10 false *a 1.083,1.854 1.396,2.052 0.313,0.198 10 false *b

Using pliers, install the boot clip.

Text in Illustration
*a Upward
*b 180°
V100135

Front of Vehicle

NOTICE:

Make sure that the claws of the clip are positioned within the area shown in the illustration.



Hide 7.INSTALL STEERING RACK BOOT CLIP LH

HINT:

Use the same procedures described for the RH side.


Hide 44416 8.INSTALL STEERING GEAR OUTLET RETURN TUBE

a.

Using a union nut wrench, install the return tube to the steering gear.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 9.INSTALL TURN PRESSURE TUBE

a.

Apply steering fluid to 2 new O-rings. Using a union nut wrench, install the 2 O-rings and turn pressure tube LH.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

HINT:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



b.

Apply steering fluid to 2 new O-rings. Using a union nut wrench, install the 2 O-rings and turn pressure tube RH.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

HINT:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 45047 10.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.

Align the matchmarks of the tie rod and rack end, and temporarily install the tie rod with the lock nut.

HINT:

After adjusting toe-in, tighten the lock nut.


Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


Hide 45046 11.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.