Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E283443E05
1.104,0.771 2.094,1 0.99,0.229 10 false from Battery 0.635,1.75 2.01,1.979 1.375,0.229 10 false from IG No. 1 Relay 5.802,4.719 7.104,5.083 1.302,0.365 10 false Radio and Display Receiver Assembly 0.833,2.708 1.969,2.938 1.135,0.229 10 false from ACC Relay 3.771,2.917 4.198,3.146 0.427,0.229 10 false ACC 3.615,0.948 4.406,1.177 0.792,0.229 10 false RAD NO. 1 3.5,1.938 4.427,2.167 0.927,0.229 10 false ECU-IG NO.2 5.771,0.573 5.979,0.74 0.208,0.167 10 false 4 5.646,0.802 5.99,0.969 0.344,0.167 10 false G36 6.073,0.74 6.271,0.906 0.198,0.167 10 false B 5.75,1.552 5.958,1.719 0.208,0.167 10 false 1 5.656,1.771 6,1.938 0.344,0.167 10 false G29 6.073,1.76 6.271,1.927 0.198,0.167 10 false IG 5.75,2.521 5.958,2.688 0.208,0.167 10 false 3 5.656,2.729 6,2.896 0.344,0.167 10 false G36 6.073,2.729 6.438,2.896 0.365,0.167 10 false ACC 5.75,3.375 5.958,3.542 0.208,0.167 10 false 7 5.667,3.594 6.01,3.76 0.344,0.167 10 false G36 6.073,3.594 6.438,3.76 0.365,0.167 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY, BODY GROUND)
U181081E02
1.531,1.438 1.271,1.823 true 2.333,0.542 2.073,0.958 true 2.323,0.958 2.646,0.781 true 0.781,3.302 0.396,3.167 true 0.104,0.125 0.292,0.281 0.188,0.156 10 false *a 1.531,2.271 1.896,2.427 0.365,0.156 10 false G29 1.531,0.208 1.875,0.365 0.344,0.156 10 false G36 0.823,1.833 1.25,2.052 0.427,0.219 10 false GND 2.75,0.625 2.938,0.844 0.188,0.219 10 false B 2.354,0.302 2.75,0.5 0.396,0.198 10 false ACC 0.125,3.063 0.354,3.26 0.229,0.198 10 false IG

a.

Disconnect the G29 and G36 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below .

Standard Resistance:
Tester Connection Condition Specified Condition
G36-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G36-3 (ACC) - G36-7 (GND) Ignition switch ACC 11 to 14 V
G36-4 (B) - G36-7 (GND) Always 11 to 14 V
G29-1 (IG) - G36-7 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR