Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2009.08–2012.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio receiver assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

WIRING DIAGRAM

E202608E03
0.729,0.927 1.094,1.073 0.365,0.146 10 false ALO 0.708,1.375 1.125,1.583 0.417,0.208 10 false ARO 0.625,1.885 1.083,2.031 0.458,0.146 10 false ASGN 0.625,2.365 1.073,2.531 0.448,0.167 10 false AGND 0.625,2.823 1.052,3.01 0.427,0.188 10 false AUXO 1.156,0.802 1.385,1.01 0.229,0.208 10 false 1 1.167,1.26 1.333,1.448 0.167,0.188 10 false 2 1.177,1.781 1.385,1.948 0.208,0.167 10 false 3 1.167,2.229 1.385,2.417 0.219,0.188 10 false 5 1.167,2.729 1.333,2.938 0.167,0.208 10 false 4 0.156,3.229 0.448,3.417 0.292,0.188 10 false F31 0.146,3.375 3.073,3.604 2.927,0.229 10 false No. 1 Stereo Jack Adapter Assembly 4.302,2.458 5.094,2.667 0.792,0.208 10 false Shielded 2.323,2.458 3.115,2.667 0.792,0.208 10 false Shielded 6.156,1.375 6.469,1.531 0.313,0.156 10 false ARI 6.177,0.896 6.49,1.052 0.313,0.156 10 false ALI 6.146,1.854 6.677,2.01 0.531,0.156 10 false ASGN 6.146,2.333 6.625,2.5 0.479,0.167 10 false AGND 6.177,2.792 6.698,2.958 0.521,0.167 10 false AUXI 5.865,0.823 6.094,1.01 0.229,0.188 10 false 17 5.854,1.771 6.115,1.979 0.26,0.208 10 false 16 5.854,2.24 6.042,2.521 0.188,0.281 10 false 18 5.865,1.292 6.052,1.5 0.188,0.208 10 false 15 5.865,2.698 6.146,2.948 0.281,0.25 10 false 19 5.521,3.198 5.771,3.385 0.25,0.188 10 false G9 5.521,3.323 7.156,3.49 1.635,0.167 10 false Radio Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO JACK ADAPTER)
a.

Disconnect the G9 radio receiver assembly connector.


b.

Disconnect the F31 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-17 (ALI) - F31-1 (ALO) Always Below 1 Ω
G9-15 (ARI) - F31-2 (ARO) Always Below 1 Ω
G9-16 (ASGN) - F31-3 (ASGN) Always Below 1 Ω
G9-18 (AGND) - F31-5 (AGND) Always Below 1 Ω
G9-19 (AUXI) - F31-4 (AUXO) Always Below 1 Ω
G9-17 (ALI) - Body ground Always 10 kΩ or higher
G9-15 (ARI) - Body ground Always 10 kΩ or higher
G9-16 (ASGN) - Body ground Always 10 kΩ or higher
G9-18 (AGND) - Body ground Always 10 kΩ or higher
G9-19 (AUXI) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR