Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.08–2013.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  CB-13  USB Over Current Detection  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
CB-13 An "iPod" or USB device overcurrent malfunction.
·

"iPod" or USB device

·

Harness or connector

·

No. 1 stereo jack adapter assembly

·

Multi-media interface ECU



WIRING DIAGRAM

E261583E02
0.501,2.02 0.787,2.162 0.286,0.142 10 G26 0.501,2.174 2.750,2.316 2.248,0.142 10 No.1 Stereo Jack Adapter Assembly 2.131,0.587 2.239,0.736 0.107,0.149 10 1 2.131,1.442 2.239,1.591 0.107,0.149 10 4 4.839,1.442 4.946,1.591 0.107,0.149 10 4 4.839,0.587 4.946,0.736 0.107,0.149 10 1 4.634,2.02 4.920,2.162 0.286,0.142 10 G27 4.634,2.174 6.286,2.316 1.651,0.142 10 Muiti-media Interface ECU

PROCEDURE

1.REPLACE USB Device OR "iPod"
a.

Disconnect the USB device or "iPod" from the stereo jack adapter.


b.

Turn the ignition switch off.

HINT:

When this DTC has been stored, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



c.

Turn the ignition switch to ACC.


d.

Connect a known good USB device or "iPod" to the stereo jack adapter.



NEXT

2.CLEAR DTC
2.CLEAR DTC

NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs and check if the same DTC occurs again.

HINT:

If DTCs are output frequently, replace the multi-media interface ECU.


OK:

Malfunction disappears.




OK

USB DEVICE OR "iPod" WAS DEFECTIVE

NG

4.CHECK MULTI-MEDIA INTERFACE ECU
4.CHECK MULTI-MEDIA INTERFACE ECU
a.
U181030E03
0.042,0 0.292,0.188 0.25,0.188 10 false *a 1.594,0.417 1.927,0.604 0.333,0.188 10 false G26

Disconnect the G26 No. 1 stereo jack adapter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-1 - G26-4 Always 5 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

REPLACE NO. 1 STEREO JACK ADAPTER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - STEREO JACK ADAPTER)
5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - STEREO JACK ADAPTER)
a.

Disconnect the G27 multi-media interface ECU connector.


b.

Disconnect the G26 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G27-1 - G26-1 Always Below 1 Ω
G27-4 - G26-4 Always Below 1 Ω
G27-1 - Body ground Always 10 kΩ or higher
G27-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR