Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056151 PARK ASSIST / MONITORING _0274042 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


E267064E03
3.385,0.083 3.771,0.333 0.385,0.25 3.49,0.125 3.802,0.323 0.313,0.198 10 false Y2

a.

Disconnect the Y2 rear television camera assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Y2-6 (CB+) - Y2-5 (CGND) R - BR Power source Within 60 seconds of turning the ignition switch to ACC 5.5 to 7.05 V
Y2-5 (CGND) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the Y2 rear television camera assembly connector.


d.

Check for pulses between each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Y2-2 (CV-) - Y2-3 (CV+) B - W Video signal Ignition switch ON
Camera lens not covered, displaying an image
Pulse generation
(See waveform 1)
Ignition switch ON
Camera lens covered, blacking out screen
Pulse generation
(See waveform 2)

HINT:
·

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

·

If the result is not as specified, the rear television camera assembly may be malfunctioning.




e.
E353046E02
0.938,2.24 1.052,2.24 1.052,2.24 1.146,1.698 true 1.531,2.229 1.385,2.229 1.385,2.229 1.281,1.594 true 0.938,4.417 1.073,4.417 1.073,4.417 1.177,3.792 true 1.583,4.406 1.438,4.406 1.438,4.406 1.333,3.729 true 0.146,0.125 0.354,0.313 0.208,0.188 10 false *a 0.188,2.323 0.396,2.51 0.208,0.188 10 false *b 0.292,1.073 0.635,1.25 0.344,0.177 10 false GND 0.292,3.344 0.635,3.521 0.344,0.177 10 false GND 0.76,2.167 0.969,2.354 0.208,0.188 10 false *c 1.615,2.146 1.823,2.333 0.208,0.188 10 false *d 0.74,4.354 0.948,4.542 0.208,0.188 10 false *c 1.625,4.333 1.833,4.521 0.208,0.188 10 false *d

Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Terminal No. (Symbol) Y2-2 (CV-) - Y2-3 (CV+)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Terminal No. (Symbol) Y2-2 (CV-) - Y2-3 (CV+)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Text in Illustration
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform