CHECK INITIAL CHECK FUNCTION
Check the initial check function for the buzzer.
When the back sonar or clearance sonar switch assembly is turned on, check that the following occurs: 1) after 0.2 seconds, the buzzer sounds for approximately 0.7 to 1.3 seconds, and 2) the system starts the obstacle detection operation.
Check the initial check function for the sensor.
Approximately 0.2 seconds after the ignition switch is turned to ON and the back sonar or clearance sonar switch assembly is turned on, all the sensors are checked by the system.
When the shift lever is operated, the system starts the obstacle detection operation.
MALFUNCTION DISPLAY (MULTI-INFORMATION DISPLAY)
Open circuit indication
If there is an open circuit between the No. 1 ultrasonic sensor and the clearance warning ECU assembly or a sensor is malfunctioning, the malfunction is displayed as shown in the illustration.
The example shows an open circuit in the No. 1 ultrasonic sensor (front left sensor).
Frozen indication
If a sensor is covered with foreign matter, such as mud or snow, the affected sensor is displayed as shown in the illustration.
The example shows that the No. 1 ultrasonic sensor (front left sensor) is covered with foreign matter.
If "CLEAN SONAR" is displayed, refer to "Frozen indication is displayed in self-check function" on Problem Symptoms Table to inspect it (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>PROBLEM SYMPTOMS TABLE).
DETECTION RANGE MEASUREMENT AND DISPLAY INSPECTION
Detection range measurement:
Make sure that the vehicle does not move by applying the parking brake firmly.
Turn the ignition switch to ON.
Move the shift lever to R to check the No. 1 ultrasonic sensors.
Turn the back sonar or clearance sonar switch assembly on.
Move a 60 mm (2.36 in.) diameter pole near each sensor to measure its detection range.
These detection ranges are applicable when positioning the 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The detection range varies depending on the measuring method and type of obstacle (such as walls).
Have an assistant move the pole.
Clearance Sonar
| *a | Approx. 950 mm (37.4 in.) | *b | Approx. 600 mm (23.6 in.) |
| *c | Approx. 500 mm (19.7 in.) | *d | Approx. 200 mm (7.9 in.) |
|
Hatched Area | - | - |
The No. 1 ultrasonic sensor side view detection range hatched area (labeled *1) represents the cross section of the top view of the lines of detection range A. The hatched area *1 does not represent the entire side view detection range.
Back Sonar
| *a | Approx. 1800 mm (70.9 in.) | *b | Approx. 1350 mm (53.1 in.) |
| *c | Approx. 1500 mm (59.1 in.) | *d | Approx. 200 mm (7.9 in.) |
| *e | Wall | *f | Approx. 600 mm (23.6 in.) |
|
Hatched Area | - | - |
When the No. 1 ultrasonic sensors (front corner sonar) have detected an obstacle, check the displays and check that the buzzer sounds.
| Ignition Switch | Clearance Sonar Main Switch | Shift Lever Position | Vehicle Speed |
|---|---|---|---|
| ON | On | In any position other than P | ·
Less than approximately 15 km/h (9.3 mph) if speed is increasing ·
Less than approximately 10 km/h (6.2 mph) if speed is decreasing |
| Detection Range | During Judgment | Obstacle |
|---|---|---|
| *1
Close-range detection Within approx. 300 +/- 30 mm (11.8 +/- 1.2 in.) |
Buzzer: Sounds continuously | 60 mm (2.36 in.) diameter pole |
| *2
Medium-range detection From approx. 300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.2 to 15.7 +/- 1.6 in.) |
Buzzer: Sounds intermittently (ON: 0.075 sec. / OFF: 0.075 sec.) | 60 mm (2.36 in.) diameter pole |
| *3
Long-range detection From approx. 450+/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.) |
Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.15 sec.) | 60 mm (2.36 in.) diameter pole |
Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.
When the No. 1 ultrasonic sensors (rear corner sonar) have detected an obstacle, check the displays and check that the buzzer sounds.
| Ignition Switch | Clearance Sonar Main Switch | Shift Lever Position | Vehicle Speed |
|---|---|---|---|
| ON | On | R | - |
| Detection Range | During Judgment | Obstacle |
|---|---|---|
| *1
Close-range detection Within approx. 300 +/- 30 mm (11.8 +/- 1.2 in.) |
Buzzer: Sounds continuously | 60 mm (2.36 in.) diameter pole |
| *2
Medium-range detection From approx. 300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.2 to 17.7 +/- 2.0 in.) |
Buzzer: Sounds intermittently (ON: 0.075 sec. / OFF: 0.075 sec.) | 60 mm (2.36 in.) diameter pole |
| *3
Long-range detection From approx. 450+/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.) |
Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.15 sec.) | 60 mm (2.36 in.) diameter pole |
Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.
When the No. 1 ultrasonic sensors (back sonar) have detected an obstacle, check the displays and check that the buzzer sounds.
| Ignition Switch | Clearance Sonar Main Switch | Shift Lever Position | Vehicle Speed |
|---|---|---|---|
| ON | On | R | - |
| Detection Range | During Detection | Obstacle |
|---|---|---|
| *1
Close-range detection Within approx. 350 +/- 40 mm (13.8 +/- 1.6 in.) |
Buzzer: Sounds continuously | 60 mm (2.36 in.) diameter pole |
| *2
Medium-range detection From approx. 350 +/- 40 to 450 +/- 50 mm (13.8 +/- 1.6 to 17.7 +/- 2.0 in.) |
Buzzer: Sounds intermittently (ON: 0.075 sec. / OFF: 0.075 sec.) | 60 mm (2.36 in.) diameter pole |
| *3
Long-range detection From approx. 450 +/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.) |
Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.15 sec.) | 60 mm (2.36 in.) diameter pole |
| *4
Longest-range detection From approx. 600 +/- 60 to 1500 +/- 150 mm (23.6 +/- 2.4 to 59.1 +/- 5.9 in.) |
Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.65 sec.) | Wall |
Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.