FAIL-SAFE FUNCTION
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
| Function | 1.
Control Master 2.
System Related |
Fail-safe Function System Behavior | User Notification | Diagnosis Code |
|---|---|---|---|---|
| Electrical Load Control
(Performs idle up according to the electrical load.) |
1.
ECM 2.
Air conditioning amplifier assembly, Main body ECU (multiplex network body ECU) |
Idle up according to the electrical load is not performed. | The idle speed changes. | - |
| Air Conditioner-linked Control
(Performs idle up according to the compressor load.) |
1.
ECM 2.
Air conditioning amplifier assembly |
Air conditioning-linked control does not operate. | Air conditioning does not operate. | - |
| Eco Driving indicator light
(Displays information to driver to encourage "ecodriving".) |
1.
ECM 2.
Combination meter assembly |
·
The indicator light does not turn on. ·
The display of all information stops. |
The eco driving indicator light does not turn on. | - |
| Integrated Control (VSC)
(Estimates the driver requested torque based on accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.) |
1.
ECM 2.
Skid control ECU (master cylinder solenoid), Yaw rate sensor assembly, Steering angle sensor (spiral cable sub-assembly) |
Integrated control is not performed. | Nothing. | - |
| Coast Downshift
(Changes the coast downshift point based on the air conditioning load and performs upshift delay according to air conditioning or heater requests.) |
1.
ECM 2.
Air conditioning amplifier assembly |
Coast downshift does not operate. | Coast downshift shock becomes stronger. | - |
| Cruise Control
(Adjusts the engine throttle valve opening amount automatically to maintain the vehicle speed.) |
1.
ECM 2.
Skid control ECU (master cylinder solenoid), Combination meter assembly |
Cruise control does not operate. | The CRUISE main indicator light and CRUISE SET indicator light blink. | - |
| ABS Control
(Controls the ABS according to the yaw rate sensor signal.) |
1.
Skid control ECU (master cylinder solenoid) 2.
Yaw rate sensor assembly |
ABS does not operate. | The ABS indicator light turns on. | U0073
U0123 U0124 |
| TRC Control
(Controls the brakes and engine torque during acceleration slip.) |
1.
Skid control ECU (master cylinder solenoid) 2.
ECM |
TRC does not operate. | The TRC indicator light turns on. | U0073
U0100 |
| VSC Control
(Controls VSC according to the yaw rate sensor and steering angle sensor signals.) |
1.
Skid control ECU (master cylinder solenoid) 2.
ECM, Yaw rate sensor assembly, Steering angle sensor (spiral cable sub-assembly) |
VSC does not operate. | The VSC indicator light turns on. | U0073
U0100 U0123 U0124 U0126 |
| Steering Sensor
(Detects the steering wheel angle.) |
1.
Skid control ECU (master cylinder solenoid) 2.
Steering angle sensor (spiral cable sub-assembly) |
- | The VSC indicator light turns on. | - |
| Vehicle Speed Information Input
(Controls solenoid current [PPS solenoid] according to the vehicle speed, steering angle, steering speed and engine speed.) |
1.
Power steering ECU assembly 2.
Skid control ECU (master cylinder solenoid) |
Changes to the 40 km/h (25 mph) assist map to perform control. | The PPS indicator light turns on. | U0129 |
| Steering Wheel Angle Information Input
(Controls solenoid current [PPS solenoid] according to the vehicle speed, steering angle, steering speed and engine speed.) |
1.
Power steering ECU assembly 2.
Steering angle sensor (spiral cable sub-assembly) |
Steering angle is fixed at 0 degrees and the steering angle speed is fixed at 360 degrees per second. | Nothing. | U0126 |
| Engine Speed Information Input
(Controls solenoid current [PPS solenoid] according to the vehicle speed, steering angle, steering speed and engine speed.) |
1.
Power steering ECU assembly 2.
ECM |
Control is performed using a fixed value of 0 rpm. | Nothing. | U0100 |
| TC DTC Output Service
(Outputs a DTC in response to a DTC output request from the combination meter assembly.) |
1.
Combination meter assembly 2.
ECM, Airbag sensor assembly |
The TC service function stops. | Nothing. | - |
| Event Data Recorder (EDR)
(Records conditions such as the vehicle speed, the amount the accelerator pedal is depressed and the shift lever position when the event data recorder recording conditions are met.) |
1.
Airbag sensor assembly 2.
ECM |
Data is not recorded. | Nothing. | - |
| SRS Warning Light Control
(Turns the warning light on/off.) |
1.
Combination meter assembly 2.
Airbag sensor assembly |
- | The SRS warning light turns on. | - |
| Collision Detection Signal (for Fuel-cut)
(Notifies the system of a collision in order to perform fuel-cut when a vehicle collision occurs.) |
1.
ECM 2.
Airbag sensor assembly |
- | Nothing. | - |
| Driver Side Seat Belt Warning Light
(Turns seat belt warning light on/off.) |
1.
Combination meter assembly, Main body ECU (multiplex network body ECU) 2.
Airbag sensor assembly |
- | Nothing. | - |
| Air Conditioning System Control
(Controls the air conditioning according to the engine coolant temperature information.) |
1.
Air conditioning amplifier assembly 2.
ECM, Combination meter assembly, Main body ECU (multiplex network body ECU) |
Maintains the current conditions. | Nothing. | U0100
U0142 U0155 |
| Speedometer
(Controls the speedometer according to the vehicle speed signals.) |
1.
Combination meter assembly 2.
Skid control ECU (master cylinder solenoid) |
0 km/h (0 mph) is indicated. | Behavior during a communication failure alerts the user. | U0129 |
| Tachometer
(Controls the tachometer according to the engine speed signals.) |
1.
Combination meter assembly 2.
ECM |
0 rpm is indicated. | Behavior during a communication failure alerts the user. | U0100 |
| Engine Coolant Temperature Gauge
(Controls the temperature gauge according to the temperature signals.) |
1.
Combination meter assembly 2.
ECM |
The temperature gauge needle is at the middle of the "C" mark or below. | Nothing. | U0100 |
| Fuel Receiver Gauge
(Controls the fuel gauge according to the vehicle condition determined by the ST signal, vehicle speed signal, and fuel amount.) |
1.
Combination meter assembly 2.
ECM, Skid control ECU (master cylinder solenoid) |
·
Operates the same as when the vehicle is stopped. ·
Operates with ST set to off. |
Nothing. | U0100
U0129 |
| ODO/TRIP Meter
(Calculates and indicates the driven distance according to the pulse count of the vehicle speed pulse signal.) |
1.
Combination meter assembly 2.
Skid control ECU (master cylinder solenoid) |
The calculation stops and the last displayed value remains. | Nothing. | U0129 |
| Shift Display
(Displays the shift information according to the shift position signal.) |
1.
Combination meter assembly 2.
ECM |
The shift display turns off. | Nothing. | U0100 |
| Telltale
(Controls indicator illumination and blinking according to the CAN signals and direct line input signals.) |
1.
Combination meter assembly 2.
ECM, Skid control ECU (master cylinder solenoid), Power steering ECU assembly, Airbag sensor assembly, Main body ECU (multiplex network body ECU) |
- | The indicator or warning lights turn on. | U0100
U0129 U0131 U0151 |
| Buzzer
(Controls the sounding of buzzers according to the CAN signals and direct line input signals.) |
1.
Combination meter assembly 2.
ECM, Skid control ECU (master cylinder solenoid), Airbag sensor assembly, Main body ECU (multiplex network body ECU) |
- | Buzzer sounds. | U0100
U0129 U0151 |
| Drive Monitor
(Performs calculations and displays drive monitor information according to the fuel injection volume and pulse count of the vehicle pulse signal.) |
1.
Combination meter assembly 2.
ECM, Skid control ECU (master cylinder solenoid), Main body ECU (multiplex network body ECU) |
The drive monitor calculations stop and the display is blank. | Nothing. | U0100
U0129 |
| Multi-information Display
(Displays the outside temperature and road surface freezing information.) |
1.
Combination meter assembly 2.
Air conditioning amplifier assembly |
The multi-information display is blank. | Nothing. | - |
| Dimming Control
(Dims the lighting level of the display or escutcheon key by turning ON and OFF the Dimmer switch.) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU) |
Control continues. | Nothing. | U0140 |
| Destination Auto-detect Function
(Detects the destination of the vehicle based on the package information.) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU) |
Control continues. | Nothing. | U0140 |
| Steering Wheel Position Detection Function
(Judges the sequence of speaker check in the diagnosis based on information on the steering wheel position.) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU) |
Control continues. | Nothing. | U0140 |
| Trip Counter
(Maintains trip counter information according to the number of times the ignition switch was set to ACC.) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU) |
Control continues. | Nothing. | U0140 |
| Time Counter
(Maintains time count information according to the time elapsed since the ignition switch was set to ACC.) |
1.
Radio and display receiver assembly 2.
Main body ECU (multiplex network body ECU) |
Control continues. | Nothing. | U0140 |
| Door Lock (Key-linked Function, Key Lock-in Prevention Function, etc.)
(Performs lock/unlock control.) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM |
Shift lever-linked auto lock or unlock operation is prohibited. | Nothing. | U0100
U0101 |
1.
Main body ECU (multiplex network body ECU) 2.
Airbag sensor assembly |
- | Nothing. | U0151 | |
1.
Main body ECU (multiplex network body ECU) 2.
Combination meter assembly |
Vehicle speed-linked auto unlock is prohibited. | Nothing. | U0155 | |
| Alarm
(Sounds warnings.) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM |
- | Nothing. | U0100
U0101 |
| Display Automatic Dimming
(Controls display dimming control.) |
1.
Combination meter assembly 2.
- |
Dims the interior display/indicators when not in the tail cancel state. | Nothing. | U0155 |
| Seat Control (Performs memory control [seat position adjustment].) | 1.
Main body ECU (multiplex network body ECU) 2.
Front power seat switch LH |
- | Nothing. | U0208 |
| ADD Switching Limitation
(Prohibits ADD actuator switching from free to lock when the difference between the vehicle wheel speeds is outside the acceptable range.) |
1.
Four wheel drive control ECU 2.
Skid control ECU (master cylinder solenoid) |
ADD switching is prohibited. | The 4WD indicator light blinks and the buzzer sounds. | - |
| Rear Differential Lock Switching Limitation
(Prohibits rear differential lock switching when the vehicle speed is outside the acceptable range .) |
1.
Four wheel drive control ECU 2.
Skid control ECU (master cylinder solenoid) |
Rear differential lock switching prohibited. | The 4WD indicator light blinks. | - |
| Specialized Control during Wheel Speed Failure
(When there is abnormal wheel speed, this control permits switching only when specified conditions are met [not all wheel speeds are abnormal, the brakes are applied, the engine speed is low and all normal wheel speeds are low].) |
1.
Four wheel drive control ECU 2.
ECM, Skid control ECU (master cylinder solenoid) |
When all 4 wheels are malfunctioning, switching is prohibited. | The 4WD indicator light blinks. | - |
| 4WD Indicator Light and Buzzer Signal Output
(Outputs a signal indicating the indicator and buzzer state, which are used to determine the actuator position and switching status.) |
1.
Four wheel drive control ECU 2.
Combination meter assembly |
State signal update not possible. | Nothing. | - |
| 4WD State Signal Output
(Outputs a signal when switching to the H4 position is finished.) |
1.
Four wheel drive control ECU 2.
Skid control ECU (master cylinder solenoid), Combination meter assembly |
State signal update not possible. | The 4WD indicator light status changes in accordance with changes in the 4WD state signal. | - |
| L4 State Signal Output
(Outputs a signal when switching to the L4 position is finished.) |
1.
Four wheel drive control ECU 2.
Skid control ECU (master cylinder solenoid), Combination meter assembly |
State signal update not possible. | The 4LO indicator light status changes in accordance with changes in the L4 state signal. | - |
| Rear Differential Lock State Signal Output
(Outputs the rear differential P/S state.) |
1.
Four wheel drive control ECU 2.
Combination meter assembly |
State signal update not possible. | The rear differential lock indicator light status changes in accordance with changes in the rear differential lock state signal. | - |
| Signal Output During Switching
(Outputs the actuator switching state.) |
1.
Four wheel drive control ECU 2.
Combination meter assembly |
State signal update not possible. | The indicator lights blink during signal output during switching. | - |
| High-Low Switching Limitation
(Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.) |
1.
Four wheel drive control ECU 2.
ECM, Skid control ECU (master cylinder solenoid) |
High-Low switching prohibited. | The 4WD indicator light blinks and the buzzer sounds. | - |
| Center Differential Lock Switching Limitation
(Prohibits center differential lock switching when the difference in wheel speeds is large.) |
1.
Four wheel drive control ECU 2.
Skid control ECU (master cylinder solenoid) |
Prohibits center differential lock switching. | The 4WD indicator light blinks and the buzzer sounds. | - |
| L4F Switching Limitation
(Prohibits switching to L4F when VSC is malfunctioning.) |
1.
Four wheel drive control ECU 2.
Skid control ECU (master cylinder solenoid) |
L4F switching is limited. | Nothing. | - |
| H-L Actuator Failure Signal Output
(Outputs a signal when the H-L actuator switch is malfunctioning.) |
1.
Four wheel drive control ECU 2.
ECM, Skid control ECU (master cylinder solenoid), Combination meter assembly |
State signal update not possible. | The indicator lights blink quickly. | - |
| Cruise Control Cancel Signal Output
(Outputs a cruise control cancel signal when center differential switching is not completed even though 5 seconds or more have elapsed from the start of switching.) |
1.
Four wheel drive control ECU 2.
ECM |
State signal update not possible. | Nothing. | - |
| Center Differential Lock State Signal Output
(Outputs the center differential lock P/S state.) |
1.
Four wheel drive control ECU 2.
Combination meter assembly |
State signal update not possible. | The status of the indicator lights changes in accordance with changes in the center differential lock state signal. | - |
| Seat Memory System (Controls the seat position according to the operating conditions.) | 1.
Front power seat switch LH 2.
Main body ECU (multiplex network body ECU) |
The seat memory system does not operate. | Nothing. | - |