Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"SRS Airbag" is not displayed on the "Bus Check" screen.


·

"Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside center airbag sensor assembly

·

Center airbag sensor assembly branch wire or connector

·

Center airbag sensor assembly



WIRING DIAGRAM

C201307E04
5.486,2.141 5.979,2.315 0.493,0.174 10 E1 5.486,1.684 5.980,1.896 0.494,0.211 10 IG2 4.895,3.352 6.949,3.544 2.054,0.192 10 Center Airbag Sensor Assembly 5.486,2.56 5.979,2.734 0.493,0.174 10 E2 4.535,1.561 4.838,1.735 0.303,0.174 10 IGN 2.749,1.686 3.719,1.872 0.969,0.186 10 from IG2 Relay 5.186,2.043 5.398,2.205 0.212,0.161 10 25 5.186,2.485 5.398,2.633 0.213,0.148 10 26 5.186,1.609 5.359,1.785 0.174,0.176 10 21 5.486,1.053 5.980,1.264 0.494,0.211 10 CANL 5.186,0.977 5.359,1.153 0.174,0.176 10 22 5.486,0.624 5.980,0.835 0.494,0.211 10 CANH 5.186,0.549 5.359,0.725 0.174,0.176 10 13 1.784,0.977 1.957,1.153 0.174,0.176 10 16 1.784,0.549 1.957,0.725 0.174,0.176 10 5 4.895,3.194 5.280,3.342 0.385,0.148 10 F33 0.429,1.521 2.031,1.713 1.601,0.192 10 No. 2 Junction Connector 0.429,1.363 0.805,1.511 0.375,0.148 10 F59

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)
a.
U180822E02
1.302,1.146 0.729,1.417 0.729,1.417 0.656,1.417 true 1.177,1.49 0.948,1.865 0.948,1.865 0.823,1.865 true 0.063,0.052 0.25,0.229 0.188,0.177 10 false *a 0.208,1.344 0.625,1.521 0.417,0.177 10 false CANH 0.281,1.021 0.594,1.198 0.313,0.177 10 false F33 0.396,1.802 0.792,1.969 0.396,0.167 10 false CANL

Disconnect the F33 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F33-13 (CANH) - F33-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CENTER AIRBAG SENSOR BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - BATTERY AND BODY GROUND)
a.
U180823E02
1.656,1.5 1.51,1.938 1.51,1.938 1.438,1.938 true 1.792,1.5 1.938,1.938 1.938,1.938 2.01,1.938 true 1,1.51 0.771,1.771 0.771,1.771 0.635,1.771 true 0.073,0.073 0.26,0.25 0.188,0.177 10 false *a 1.219,1.885 1.438,2.063 0.219,0.177 10 false E1 2.063,1.854 2.281,2.031 0.219,0.177 10 false E2 0.333,1.698 0.583,1.875 0.25,0.177 10 false IG2 0.271,1.01 0.583,1.188 0.313,0.177 10 false F33

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-25 (E1) - Body ground Always Below 1 Ω
F33-26 (E2) - Body ground



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F33-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR