Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "Bus Check" screen.

·

"4WD Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside four wheel driver control ECU

·

Four wheel driver control ECU branch wire or connector

·

Four wheel driver control ECU



For vehicles with four wheel drive.


WIRING DIAGRAM

C361682E01
1.938,0.458 2.073,0.635 0.135,0.177 10 false 3 1.927,0.885 2.125,1.073 0.198,0.188 10 false 14 0.49,1.458 0.792,1.635 0.302,0.177 10 false F60 0.479,1.635 2.052,1.844 1.573,0.208 10 false No. 3 Junction Connector 5.49,0.354 5.688,0.531 0.198,0.177 10 false 19 5.448,0.583 5.708,0.75 0.26,0.167 10 false F47 5.438,1.021 5.698,1.188 0.26,0.167 10 false F47 5.448,1.885 5.708,2.052 0.26,0.167 10 false F46 5.448,2.323 5.708,2.49 0.26,0.167 10 false F46 5.49,0.813 5.677,0.99 0.188,0.177 10 false 20 5.51,1.677 5.656,1.844 0.146,0.167 10 false 3 5.51,2.156 5.635,2.313 0.125,0.156 10 false 4 4.688,1.771 5.031,1.938 0.344,0.167 10 false 4WD 2.354,1.896 3.667,2.094 1.313,0.198 10 false from IG1 NO. 3 Relay 5.792,0.594 6.188,0.771 0.396,0.177 10 false CANH 5.792,1.031 6.177,1.208 0.385,0.177 10 false CANL 5.781,1.885 5.948,2.073 0.167,0.188 10 false IG 5.802,2.323 6.156,2.5 0.354,0.177 10 false GND 5.167,2.792 7.073,3.01 1.906,0.219 10 false Four Wheel Drive Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
U180841E02
0.479,1.01 0.563,1.01 0.563,1.01 0.677,1.344 true 0.594,0.708 0.688,0.708 0.688,0.708 0.76,1.354 true 0.063,0.021 0.229,0.208 0.167,0.188 10 false *a 0.146,0.646 0.552,0.802 0.406,0.156 10 false CANH 0.083,0.948 0.458,1.115 0.375,0.167 10 false CANL 2.438,1.24 2.74,1.396 0.302,0.156 10 false F47

Disconnect the F47 four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F47-19 (CANH) - F47-20 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)
a.
U180840E02
1.76,1.198 1.844,1.198 1.844,1.198 2.042,1.438 true 1.969,0.958 2.063,0.958 2.063,0.958 2.167,1.427 true 0.063,0.063 0.26,0.271 0.198,0.208 10 false *a 1.479,1.479 1.75,1.646 0.271,0.167 10 false F46 1.76,0.896 1.948,1.063 0.188,0.167 10 false IG 1.385,1.135 1.708,1.302 0.323,0.167 10 false GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the F46 four wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F46-4 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F46-3 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)


OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR