Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2013.08
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the front power seat switch LH.
·

Power source or inside front power seat switch LH

·

Front power seat switch LH branch wire or connector

·

Front power seat switch LH



HINT:

For vehicles with a seat position memory only.


WIRING DIAGRAM

C293159E02
4.788,3.911 6.563,4.078 1.774,0.167 10 Front Power Seat Switch LH 0.637,1.92 1.037,2.096 0.400,0.176 10 F82 0.637,2.08 2.292,2.256 1.655,0.176 10 No. 2 Junction Connector 5.269,1.038 5.735,1.214 0.466,0.176 10 CANP 1.945,0.927 2.054,1.081 0.109,0.154 10 3 5.07,0.847 5.252,1.000 0.181,0.154 10 8 5.014,2.512 5.196,2.666 0.181,0.154 10 12 5.07,1.28 5.252,1.433 0.181,0.154 10 7 5.07,2.055 5.262,2.209 0.192,0.154 10 7 5.07,3.051 5.273,3.204 0.203,0.154 10 2 2.446,2.699 3.249,2.870 0.802,0.172 10 from Battery 2.446,2.236 3.249,2.408 0.802,0.172 10 from Battery 1.945,1.381 2.139,1.534 0.194,0.153 10 14 5.269,1.475 5.735,1.652 0.466,0.176 10 CANN 5.269,2.689 5.735,2.865 0.466,0.176 10 SYSB 5.269,2.24 5.735,2.417 0.466,0.176 10 +B1 5.269,3.248 5.735,3.425 0.466,0.176 10 GND1 4.959,1.476 5.223,1.652 0.265,0.176 10 b19 4.959,2.7 5.223,2.876 0.265,0.176 10 b19 4.959,2.241 5.223,2.417 0.265,0.176 10 b18 4.959,3.231 5.223,3.407 0.265,0.176 10 b18 4.959,1.042 5.223,1.218 0.265,0.176 10 b19 3.968,2.37 4.717,2.524 0.749,0.154 10 P/SEAT FL 4.107,2.834 4.597,2.988 0.490,0.154 10 ECU-B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH LH BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH LH BRANCH WIRE)
a.
U150333E01
0.078,0.055 0.251,0.223 0.173,0.168 10 *a 2.593,1.626 3.028,1.794 0.435,0.168 10 CANN 2.478,1.852 2.913,2.020 0.435,0.168 10 CANP 2.58,1.714 2.485,1.714 2.485,1.714 2.336,1.579 false 2.466,1.94 2.376,1.94 2.376,1.94 2.241,1.593 false 1.315,1.301 1.589,1.469 0.274,0.168 10 b19

Disconnect the b19 front power seat switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
b19-8 (CANP) - b19-7 (CANN) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch LH)



OK

3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE FRONT POWER SEAT SWITCH LH CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - BATTERY AND BODY GROUND)
a.
U150334E03
1.573,1.677 1.469,1.677 1.469,1.677 1.396,1.427 true 1.885,1.979 1.979,1.979 1.979,1.979 2.083,1.604 true 1.542,0.875 1.448,0.875 1.448,0.875 1.385,1.198 true 0.281,0.104 0.458,0.271 0.177,0.167 10 false *a 1.615,1.604 1.906,1.771 0.292,0.167 10 false +B1 1.479,1.896 1.875,2.063 0.396,0.167 10 false SYSB 0.24,1.146 0.51,1.313 0.271,0.167 10 false b18 2.865,1.156 3.135,1.323 0.271,0.167 10 false b19 1.583,0.781 1.99,0.948 0.406,0.167 10 false GND1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the b18 front power seat switch LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-2 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b18-7 (+B1) - Body ground Always 11 to 14 V
b19-12 (SYSB) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch LH)


OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR